1、REVISIONS LTR DESCRIPTION DATE APPROVED Requirements of DSCC drawing 84148 are applicable. Prepared in accordance with ASME Y14.100 REV PAGE REV REV STATUS OF PAGES PAGE 1 2 3 4 5 PREPARED BY PMIC G Ron Gary DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 CHECKED BY Lee Surowiec APPROVED B
2、Y Richard Taylor TITLE CONNECTOR, RECEPTACLE, ELECTRICAL, SERIES BMZ, PIN CONTACT, FOR SEMIRIGID CABLE SIZE CAGE CODE 037Z3 DWG. NO. 04014 Original date of drawing 9 July 2004 A REV PAGE 1 OF 5 AMSC N/A 5935-E741 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr
3、om IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 04014 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV PAGE 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Wrench flats are to accommodate standard wrench opening in accordance with FED-STD-H
4、28, appendix 10. 4. All undimensioned pictorial configurations are for reference purposes only. 5. Method of assembly to the cable shall be solder. 6. Unless otherwise specified, tolerances are .005 (0.13 mm). 7. Series BMZ interface in accordance with MIL-STD-348, pin contact. FIGURE 1. General con
5、figuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 04014 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV PAGE 3 ENGINEERING DATA: Nominal impedance: 50 ohms. Frequency range: 2 - 18 GHz. (Connector
6、performance only, frequency range is dependent on cable used.) Voltage rating: 335 V rms at sea level. 85 V rms at 70,000 feet. Temperature rating: -65C to +165C. REQUIREMENTS: Requirements of drawing 84148 is applicable. Dimensions and configuration: See figure 1 and MIL-STD-348. Force to engage an
7、d disengage: Longitudinal force: 12 ounces, max. Torque: Not applicable. Coupling proof torque: Not applicable. Hermetic seal: Not applicable. Leakage (pressurized connectors): Not applicable. Center contact retention: 4 pounds minimum, axial force Radial torque: Not applicable. Voltage standing wav
8、e ratio (VSWR): 1.07 + .010 F (GHz), maximum. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 04014 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV PAGE 4 Moisture resistance: Method 106, MIL-STD-202, no mea
9、surements at high humidity. Insulation resistance shall be at least 200 megohms within 5 minutes after removal from humidity. Insulation resistance: Method 302, test condition B, MIL-STD-202, 10,000 megohms, minimum. Contact resistance (in milliohms, maximum): Initial After environment Center contac
10、t: 4.0 4.0 Outer contact: 2.0 Not applicable Outer conductor to body: 0.5 Not applicable Dielectric withstanding voltage at sea level: 1000 V rms, minimum. 250 V rms at 70,000 feet. Vibration, high frequency: Method 204, test condition D, MIL-STD-202. Corona level: Altitude: 70,000 feet. 250 V rms,
11、minimum. Shock (specified pulse): Method 213, test condition I, MIL-STD-202. Thermal shock: Method 107, test condition B, MIL-STD-202, except test high temperature shall be +85C. Barometric pressure (reduced): Not applicable. RF high potential withstanding voltage: 670 V rms, minimum. Frequency: 5 M
12、Hz. Leakage current: Not applicable. Cable retention force: 30 pounds, minimum. Torque: 16 ounce-inches, minimum. Coupling mechanism retention force: Not applicable. RF leakage: -85 F (F in GHz) dB, minimum. Test at a frequency between 2 and 3 GHz. RF insertion loss: .04 F, GHz dB, maximum. Note: Th
13、ese parts are for use in general radio frequency applications. Part or Identifying Number (PIN): See table I. TABLE I. Connector to cable reference. PIN Cable accommodation 04014ZSPA M17/133-RG405 M17/133-0001 through -00005 Provided by IHSNot for ResaleNo reproduction or networking permitted withou
14、t license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 04014 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV PAGE 5 Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed on the requirements drawing have agreed to this d
15、rawing and a certificate of compliance has been submitted to DSCC-VAI. DSCC drawing PIN 1/ Vendor CAGE number Vendor reference PIN 04014ZSPA 95077 SF8914-6002 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Vendor CAGE Vendor name number and address 95077 S/V Microwave, Inc. 2400 Centrepark West Dr. WPB, FL 33409 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
