1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Added three sources for all dash numbers 05 Sep 85 Ivan R. Jones B Modified figure 1 and added footnotes. Added tables II and III. Deleted references to MIL-D-23859; substituted references to MIL-D-83532. Updated vendor table. 01 Jul 87 Randy Larson C Chang
2、ed standoff requirements in note 4 of figure 1. 19 Oct 87 Randy Larson D Corrected ICCLmax limit on table III. Added note 6 to figure 1. Changed pin length and added tolerances to pin dimensions. Added three vendors. Editorial changes throughout. 17 Aug 88 Randy Larson E Changed 3.3. Moved output ri
3、se time data from table III to 3.6. Changed several dimensions on figure 1 and added notes 7 and 8. Deleted vendors 92912 and 56289. 21 Dec 92 Tony Westphal F Change in accordance with NOR 5999-R004-00. 04 Aug 00 Kendall A. Cottongim G Editorial changes made throughout. 04 Feb 08 Michael A. Radecki
4、H Editorial changes made throughout. 21 Nov 13 Michael A. Radecki Prepared in accordance with ASME Y14.100 REV STATUS OF PAGES REV H H H H H H H H H PAGES 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY Randy Larson DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 Original date of draw
5、ing 25 February 1985 CHECKED BY Randy Larson TITLE DELAY LINES, ACTIVE, 5 TAPS, 14-PIN DIP, TTL INTERFACED APPROVED BY Ivan R. Jones SIZE A CODE IDENT. NO. 14933 DWG NO. 85008 REV H PAGE 1 OF 9 AMSC N/A 5999-2013-E01CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY Land and Maritime C
6、OLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85008 REV H SHEET 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a family o
7、f active 14-pin, 5 tap, TTL-interfaced delay lines. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 85008 -01 | | | | Drawing number Dash number 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specificati
8、on. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of
9、 documents in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specifi
10、ed, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-DTL-19491 - Semiconductor Devices, Packaging of. MIL-PRF-38535 - Integrated Circuits (Microcircuits) Manufacturing, General Specification for. MIL-PRF-83532 - Delay Lines, Acti
11、ve, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Microcircuits. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/quicksearch.dla.mil or https:/assist.dla.mil or from the Standardization Document Order Desk
12、, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. AMERICAN S
13、OCIETY FOR TESTING AND MATERIALS INTERNATIONAL (ASTM) ASTM-B545 - Standard Specification for Electrodeposited Coatings of Tin. (Copies of this document are available on www.astm.org or from American Society for Testing and Materials International (ASTM), 100 Barr Harbor Drive, P. O. Box C700, West C
14、onshohocken, PA, 19428-2959.) 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption h
15、as been obtained. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85008 REV H SHEET 3 3. REQUIREMENTS 3.1 Case material. The case material shall be molded diallyl phth
16、alate or encapsulated epoxy and be in accordance with MIL-PRF-83532. 3.2 Interface and physical dimensions. The interface and physical dimensions shall be in accordance with figure 1 and table I. 3.3 Terminal material. The terminal material shall be in accordance with MIL-PRF-38535. 3.4 Integrated c
17、ircuits (ICs). ICs shall meet the requirements of MIL-STD-883, level B, as a minimum. 3.5 Delay times. The delay times from input to all taps shall be as specified in table I (+25C) and table II (-55C and +125C). 3.6 Output rise time. 4 ns maximum under the following conditions: VCC= 5.0 V; TRI 3 ns
18、; CL= 50 pF; RL= 500 ohms. Applied to leading edge only. 3.7 DC characteristics. DC characteristics shall be as specified in table III. 3.8 Delay line fan-out. The delay line fan-out shall be 20 maximum (20 TTL loads per delay line). 3.9 Tap fan-out. The tap fan-out shall be 10/tap maximum (one tap
19、is capable of driving 10 TTL load maximum). 3.10 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requi
20、rements, and promotes economically advantageous life cycle costs. 3.11 Manufacturer eligibility. To be eligible for listing as a approved source of supply, a manufacturer shall be listed on the MIL-PRF-83532 Qualified Product List for at least one part, or perform the Group A and Group C inspections
21、 specified herein on a sample of parts agreed upon by the manufacturer and DLA Land and Maritime-VA. 3.12 Certificate of compliance. A certificate of compliance is required from each manufacturer requesting to be listed as an approved source of supply (see 6.3). The certificate shall state that the
22、manufacturers product meets all the requirements of this drawing. 3.13 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum
23、 of 3 percent lead, by mass (see 6.3). 3.14 Marking. Each delay line shall be marked on the top in accordance with method I of MIL-STD-1285 with the following information: a. Complete PIN (see 1.2). b. Index mark identification (over pin 1, input). c. Manufacturers Commercial and Government Entity (
24、CAGE) code or logo. d. Date code. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85008 REV H SHEET 4 3.15 Workmanship. Parts shall be processed in such a manner as to
25、 be representative of controlled industrial techniques. Surfaces shall be free from burrs, die marks, chatter marks, scratches, dirt, grease, scale, splinters, and other defects that will affect life, serviceability, performance, or appearance. Visible parting line is acceptable. FIGURE 1. Interface
26、 and physical dimensions. Inches mm Inches mm .002 0.05 .105 2.67 .003 0.08 .125 3.18 .010 0.25 .150 3.81 .012 0.30 .195 4.95 .015 0.38 .200 5.08 .018 0.46 .300 7.62 .030 0.76 .510 12.95 .100 2.54 .810 20.57 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH
27、S-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85008 REV H SHEET 5 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .005 (0.13 mm). 4. Location and shape of standoff
28、s are optional. 5. Pins 2, 3, 5, 9, 11, and 13 may be omitted at the manufacturers option. 6. Tolerances on dimensions separating leads are non-accumulative. 7. Leads shall be free of case meniscus and other foreign material and shall be solderable for a minimum of .010 inch above the seating plane
29、of the delay line. 8. Leads may be round at the discretion of the manufacturer. Round lead diameter shall be .020 .002. FIGURE 1. Interface and physical dimensions. - Continued Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPL
30、Y CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85008 REV H SHEET 6 TABLE I. Delay times at +25C, VCC= 5.00 .01 volts.PIN 85008- Delay times in nanoseconds Pin 12 tap 1 Pin 4 tap 2 Pin 10 tap 3 Pin 6 tap 4 Pin 8 output 01 02 03 04 05 5 2 ns 6 2 ns 7 2 ns 8 2 ns 9 2 ns 10 2 ns 12 2 ns 14 2
31、ns 16 2 ns 18 2 ns 15 2 ns 18 2 ns 21 2 ns 24 2 ns 27 2 ns 20 2 ns 24 2 ns 28 2 ns 32 2 ns 36 2 ns 25 2 ns 30 2 ns 35 2 ns 40 2 ns 45 5% 06 07 08 09 10 10 2 ns 15 2 ns 20 2 ns 25 2 ns 30 2 ns 20 2 ns 30 2 ns 40 2 ns 50 5% 60 5% 30 2 ns 45 5% 60 5% 75 5% 90 5% 40 2 ns 60 5% 80 5% 100 5% 120 5% 50 5%
32、75 5% 100 5% 125 5% 150 5% 11 12 13 14 15 35 2 ns 40 2 ns 45 5% 50 5% 60 5% 70 5% 80 5% 90 5% 100 5% 120 5% 105 5% 120 5% 135 5% 150 5% 180 5% 140 5% 160 5% 180 5% 200 5% 240 5% 175 5% 200 5% 225 5% 250 5% 300 5% 16 17 18 19 70 5% 80 5% 90 5% 100 5% 140 5% 160 5% 180 5% 200 5% 210 5% 240 5% 270 5% 3
33、00 5% 280 5% 320 5% 360 5% 400 5% 350 5% 400 5% 450 5% 500 5% TABLE II. Delay times at -55C and +125C, VCC= 5.00 .01 volts.PIN 85008- Delay times in nanoseconds Pin 12 tap 1 Pin 4 tap 2 Pin 10 tap 3 Pin 6 tap 4 Pin 8 output 01 02 03 04 05 5 3 ns 6 3 ns 7 3 ns 8 3 ns 9 3 ns 10 3 ns 12 3 ns 14 3 ns 16
34、 3 ns 18 3 ns 15 3 ns 18 3 ns 21 3 ns 24 3 ns 27 3 ns 20 3 ns 24 3 ns 28 3 ns 32 3 ns 36 3 ns 25 3 ns 30 3 ns 35 3 ns 40 3 ns 45 8% 06 07 08 09 10 10 3 ns 15 3 ns 20 3 ns 25 3 ns 30 3 ns 20 3 ns 30 3 ns 40 3 ns 50 8% 60 8% 30 3 ns 45 8% 60 8% 75 8% 90 8% 40 3 ns 60 8% 80 8% 100 8% 120 8% 50 8% 75 8%
35、 100 8% 125 8% 150 8% 11 12 13 14 15 35 3 ns 40 3 ns 45 8% 50 8% 60 8% 70 8% 80 8% 90 8% 100 8% 120 8% 105 8% 120 8% 135 8% 150 8% 180 8% 140 8% 160 8% 180 8% 200 8% 240 8% 175 8% 200 8% 225 8% 250 8% 300 8% 16 17 18 19 70 8% 80 8% 90 10% 100 10% 140 8% 160 8% 180 8% 200 8% 210 8% 240 8% 270 8% 300
36、8% 280 8% 320 8% 360 8% 400 8% 350 8% 400 8% 450 8% 500 8% Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85008 REV H SHEET 7 TABLE III. DC characteristics. Test Symb
37、ol Conditions -55C TC +125C Limits Unit Min Max High level output voltage VOHVCC= 4.5 V VIH= 2.0 V IOH= -1 mA 2.5 - V Low level output voltage VOLVCC= 4.5 V VIL= 0.8 V IOL= 20 mA - .5 V Input clamp voltage VICVCC= 4.5 V II = -18 mA TC= +25C - -1.2 V High level input current IIH1VCC= 5.5 V, VIH= 2.7
38、V - 50 A IIH2VCC= 5.5 V, VIH= 5.5 V - 1000 A Low level input current IILVCC= 5.5 V, VIL= .5 V - -2.00 mA Short circuit output current IOSVCC= 5.5 V, VOS= 0.0 V Not more than one output shorted at a time -40 -150 mA Low level supply current ICCLVCC= 5.5 V VI= 0.0 V - 75 mA Provided by IHSNot for Resa
39、leNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85008 REV H SHEET 8 4. VERIFICATION 4.1 Conformance inspection. 4.1.1 Inspection of product for delivery. Inspection of product for delivery shall
40、 consist of compliance with group A inspection for level A of MIL-PRF-83532. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personne
41、l, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packag
42、ing data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not m
43、andatory.) 6.1 Intended use. Devices conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. 6.2 Ordering data. The contract or purchase order should specif
44、y the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.3 Tin whisk
45、er growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Con
46、formal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited
47、Coatings of Tin) 6.4 Users of record. Coordination of this document for future revisions is coordinated only with the approved source(s) of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at mailto:relaydla.mil or if in
48、writing to: DLA Land and Maritime, ATTN: DLA Land and Maritime/VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4481 or DSN 850-4481. 6.5 Approved source(s) of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained online at mailto:relaydla.mil, or by contacting
