1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Changed manufacturers eligibility. 24 August 87 S. Searcy B Added vendor CAGE 31757 as an approved source. Editorial changes throughout. 7 May 92 D. Moore C Changes in accordance with NOR 5945-R003. 2 Mar 00 K. Cottongim D Validation and update. 17 Sep 03 K
2、. Cottongim E Technical change to paragraph 2.4.7 10 Dec 03 K. Cottongim F Incorporated boilerplate updates. Modified can height of Figure 1. Added approved source of supply. 17 July 08 Michael A. Radecki Prepared in accordance with ASME Y14.100 Source control drawing REV F F F F F F F F F F F REV S
3、TATUS OF PAGES PAGES 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY James R. Martin DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 CHECKED BY Richard A. Yannitti APPROVED BY Steven B. Searcy TITLE RELAYS, SOLID STATE, OPTICALLY ISOLATED, HERMETICALLY SEALED, ANALOG SIGNAL SWIT
4、CHING, SPST (N.O.), CMOS AND TTL CONTROL INPUTS, 1 AMPERE, 60 V DC MAXIMUM SIZE A CODE IDENT. NO. 14933 DWG NO. 86001 Original date of drawing 13 January 1986 REV F PAGE 1 OF 11 AMSC N/A 5945-E139 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBU
5、S, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 86001 REV F PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a sealed solid-st
6、ate relay supplied to “Y“ screening requirements of MIL-PRF-28750. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 86001 -001 | | | | Drawing Dash number number 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of
7、this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified
8、 requirements of documents in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless o
9、therwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-28750 - Relays, Solid State, Sealed, General Specification For FSC 5945. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Test Method Standard Electronic and E
10、lectrical Component Parts. MIL-STD-750 - Test Method Standard Test Methods for Semiconductor Devices. MIL-STD-883 - Test Method Standard, Microcircuits, FSC 5962 MIL-STD-1285 - Marking of Electrical and Electronic Parts, FSC: 59GP (Copies of these documents are available online at http:/assist.daps.
11、dla.mil/quicksearch/ or http:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this d
12、ocument takes precedence, unless otherwise noted. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-28750, and as spe
13、cified herein. 3.2 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-28750 and herein (see figure 1). 3.3 Input characteristics. 3.3.1 Five terminal/CMOS input control. See figure 1. 3.3.1.1 Bias voltage. 3.8 to 32 V dc (see table I). 3.3.1.2 B
14、ias current. 16 mA maximum. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 86001 REV F PAGE 3 TABLE I. Series control/bias resistor selection. 1/ VC range 3.8- 6 V 6.
15、0- 10 V 10- 14 V 14- 18 V 18- 22 V 22- 26 V 26- 32 V Rs Ohms 300 620 910 1,200 1,500 2,000 Power rating watts Not required 1/4 1/4 1/2 1/2 1/2 1 1/ Limiting resistor required over 6.0 volts when not used with a heat sink; with a heat sink, the values are to be determined. 3.3.1.3 Control current. 25
16、0 microamperes maximum at 5 V dc control voltage. 3.3.1.4 Control turn-off voltage. 2.8 V dc minimum at +25C to +100C. 3.3.1.4.1 Control turn-off voltage. 3.2 V dc minimum (-55C to +25C). 3.3.1.5 Control turn-on voltage. 0.5 V dc maximum at -55C to +25C. 3.3.1.5.1 Control turn-on voltage. 0.3 V dc m
17、aximum (+25C to +100C). 3.3.1.6 Schmitt hysteresis. 0.7 V dc minimum. 3.3.1.7 Control voltage range. 0 V dc to 18 V dc. 3.3.2 Four terminal/TTL input control. See figure 1. 3.3.2.1 Input current. 16 milliamperes. 3.3.2.2 Control voltage range. 3.8 V dc to 6 V dc TTL mode. 3.8 V dc to 32 V dc termina
18、l mode (see table I). 3.3.2.3 Control turn-off voltage. 1.5 V dc maximum. 3.3.2.4 Control turn-on voltage. 3.8 V dc minimum. 3.4 Output characteristics. 3.4.1 Output voltage. 60 V dc maximum. 3.4.2 On-state resistance. 0.35 ohm maximum (measured at 100 mA at 25C). Provided by IHSNot for ResaleNo rep
19、roduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 86001 REV F PAGE 4 NOTE: For on-state resistance at temperatures other than +25C, use the following equation: R = R25x e(0.006 x T) Where: R25= resistance
20、 at +25C from table I. R = resistance at new temperature. T = (T -25C). e = 2.7182818. 3.4.3 Load current. 1.0 ampere maximum at +25C (see figure 2). 3.4.4 Turn-on time (tON). 2.2 milliseconds maximum at -55C to +25C. 3.0 milliseconds maximum at +25C to +100C (see figure 3). 3.4.5 Turn-off time (tOF
21、F). 3.0 milliseconds maximum (see figure 3). 3.4.6 Output voltage drop. 0.6 volt maximum (at rated current). 3.4.7 Off-state leakage. 10 microamperes maximum at 60 V dc. 3.4.8 Transient voltage. 80 V dc maximum for 2 seconds maximum, single pulse. 3.4.9 Exponential rate of voltage rise (dv/dt). Not
22、applicable. 3.5 Electrical characteristics. 3.5.1 Insulation resistance. Input to output Input to case 1,000 megohms minimum. Output to case 3.5.2 Dielectric strength. Input to output Input to case 1,000 V rms minimum. Output to case 3.5.3 Reverse polarity. Applicable. Provided by IHSNot for ResaleN
23、o reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 86001 REV F PAGE 5 Inches Millimeters Ltr Min Max Min Max A - .335 - 8.51 B - .290 - 7.37 C .700 - 17.78 - D .190 .210 4.83 5.33 E .016 .019 0.41 0.4
24、8 F .029 .033 0.74 0.84 G .090 .110 2.29 2.79 H .075 .095 1.91 2.41 J .090 .110 2.29 2.79 K .070 .090 1.78 2.29 L - .370 - 9.40 M .022 .042 0.56 1.07 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .010 (0.
25、25 mm). 4. Terminal numbers shown above are for reference only. 5. Loads may be connected to either terminal 7, terminal 1, or both (split loads). 6. See table I for value of RSwhen VC 6 V. FIGURE 1. Outline drawing and dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted
26、 without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 86001 REV F PAGE 6 FIGURE 1. Outline drawing and dimensions - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRON
27、ICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 86001 REV F PAGE 7 FIGURE 2. Output current vs ambient temperature. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO
28、. 14933 DWG NO. 86001 REV F PAGE 8 NOTES: 1. tON+ TdON+ tr. 2. tOFF+ TdOFF+ tf. 3. Input transition should be 1.0 ms. FIGURE 3. Turn-on and turn-off time waveform. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYT
29、ON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 86001 REV F PAGE 9 3.6 ENVIRONMENTAL DATA 3.6.1 Operating temperature range. -55C to maximum per thermal operating curve (see figure 2). 3.6.2 Storage temperature range. -55C to +125C. 3.6.3 Shock. MIL-STD-202, method 213, test condition F, (1,500 gs for
30、0.5 ms, 1/2 sine wave). 3.6.4 Vibration. MIL-STD-202, method 204, test condition D, 100 gs, 10 to 3,000 Hz. 3.6.5 Seal. Hermetic, in accordance with MIL-PRF-28750. 3.6.6 Resistance to soldering heat. Applicable. 3.6.7 Salt spray (atmosphere). MIL-STD-750, method 1041. 3.6.8 Acceleration. MIL-STD-883
31、, method 2001, test condition A, 5,000 gs, Y1 axis. 3.6.9 Electromagnetic interference. Not applicable. 3.6.10 Moisture resistance. Not applicable. 3.6.11 Overload. Applicable. 3.7 Physical. Physical requirements shall be as specified herein. 3.7.1 Weight. 2 grams maximum (.07 ounce). 3.7.2 Dimensio
32、ns and configuration. See figure 1. 3.8 Conformance requirements. Relays furnished under this drawing shall have been subjected to, and passed all the requirements, tests, and inspections detailed herein. 3.8.1 Conformance inspection. Conformance inspection shall be in accordance with MIL-PRF-28750
33、and 4.2 herein. 3.9 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economic
34、ally advantageous life cycle costs. 3. 10 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-28750 Qualified Product List for at least one part, or perform the Group A inspection specified herein on a sample of parts ag
35、reed upon by the manufacturer and DSCC-VA. 3.11 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.12 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally
36、. Tin content of components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.5). 3.13 Marking. Marking shall be in accordance with MIL-STD-1285, except the relay shall be marked with the PIN as specified herein (see 1.2), the manu
37、facturers name of Commercial and Government Entity (CAGE) code, and date lot codes. 3.14 Workmanship. The relay shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Sampling and inspection. Unless otherwise specified, samplin
38、g and inspection procedures shall be performed in accordance with MIL-PRF-28750, except as modified herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 86001 REV F
39、 PAGE 10 4.2 Conformance inspection. Conformance inspection shall be in accordance with group A listing of MIL-PRF-28750. Group A testing shall be performed on each inspection lot and manufacturers shall keep lot records for 3 years (minimum), monitor for compliance to the prescribed procedures, and
40、 observe that satisfactory manufacturing conditions and records on lots are maintained for these relays. 4.2.1 Group A inspection. Group A inspection shall consist of all tests specified in MIL-PRF-28750 for the “Y“ screening level except internal components used internally to the relay shall not re
41、quire hermetic packaging. Temperature range shall be as specified in 3.6.1. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.3). When actual packaging of materiel is to be performed by DoD personnel, these personne
42、l need to contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the Military Departments System Command. Packaging
43、data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not manda
44、tory.) 6.1 Notes. Only definitions of the notes specified in MIL-PRF-28750 will apply to this drawing. 6.2 Intended use. Relays conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not ava
45、ilable for OEM application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing on QPL-28750; this
46、drawing will become inactive for new design. The QPL-28750 product shall be the preferred item for all applications. 6.3 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data
47、or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.4 Replaceability. Relays covered by this drawing will replace the same generic device covered by a contractor prepared specificatio
48、n or drawing. 6.5 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit
