1、REVISIONS LTR DESCRIPTION DATE APPROVED A Delete “part number” and substitute “Part or Identifying Number (PIN). Vendor CAGE 60563, PINs, delete and substitute new PINs. Editorial changes throughout. 01-01-22 Robert M. Heber B Add Vendor CAGE SW884, delete MIL-STD-1344 test methods, add EIA-364 test
2、 procedures 06-01-20 Richard L. Taylor Prepared in accordance with ASME-Y14.100 REV PAGE REV B A A B B REV STATUS OF PAGES PAGE 1 2 3 4 5 PREPARED BY PMIC G Ralph Antonelli DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 CHECKED BY TITLE Carl Dello-Stritto APPROVED BY Charles W. Koeller CO
3、NNECTOR, ELECTRICAL, INSERT ARRANGEMENT, MINIATURE, THIRTY TWO SIZE 20 SIGNAL CONTACTS, WITH FOUR SIZE 8 CONTACT CAVITIES SIZE CAGE CODE 037Z3 DWG. NO.89082 Original date of drawing 31 July 1990 A REV B PAGE 1 OF 5 AMSC N/A 5935-E777-000 Provided by IHSNot for ResaleNo reproduction or networking per
4、mitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Engaging face (pin) Inches mm Inches mm .055 .056 .109 .112 .163 .218 .272 .326 1.40 1.42 2.77 2.84 4.14 5.54 6.41 8.28 .381 .435 .489 .544 .598 .652 .761 .870 9.68 11.05 12.42 13.81 15.19 16.56 19.33 22.10 NOTES: 1. Dimensions are in inches
5、 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerance for three place decimals is .005 inch (0.13 mm). 4. All dimensions are true position (TP). 5. Contact holes in insert shall be located on TP within a .005 inch (0.13 mm) diameter circle. 6. Markings are
6、shown for the pin insert front. Socket inserts are the opposite. 7. Reference documents shall be of the issue in effect on date of invitations for bid. 037Z3 89082 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVA PAGE2 FIGURE 1. Insert arrangement, thirty-two size 20 signal contacts, w
7、ith four size 8 contact cavities. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. ENGINEERING DATA: Voltage rating: 500 volts rms at sea level. Operating temperature: -55C to +125C. REQUIREMENTS: Requirements of drawing 85039 a
8、nd MIL-DTL-24308 are applicable. Dimensions and configurations: See figure 1. Signal contact specifications: Style A: (crimp removable signal contacts) Socket: M39029/63-368. Pin: M39029/64-369. Style B: (solder fixed signal contacts) Socket: MIL-DTL-24308, Appendix B, figure B-1. Pin: MIL-DTL-24308
9、 Appendix B, figure B-2. Shell size: Five. Shell specifications: Style A: Socket: MIL-DTL-24308/2, figure 1. Pin: MIL-DTL-24308/4, figure 1. Style B: Socket: MIL-DTL-24308/1, figure 1. Pin: MIL-DTL-24308/3, figure 1. Tools: Connectors with crimp removable signal contacts shall be designated for con
10、tact insertion and removal with the applicable military tool as follows: Contact size Tool PIN20 M81969/39 - 01 with plastic tip M81969/1-02 with metal tip 037Z3 89082 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVA PAGE3 Provided by IHSNot for ResaleNo reproduction or networking perm
11、itted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Mating and unmating forces (with signal contacts only installed): See table I. TABLE I. Mating and unmating forces. Mating force (pounds) Unmating force (pounds) Contact type Minimum Maximum Minimum Maximum Signal 1.23 20.93 1.23 12.3 Contact
12、 resistance: See table II. TABLE II. Contact resistance (millivolts maximum). 1/ Contact classes G, D, M, N Contact Size AWG wire Size Test current (amperes) After salt spray All others 20 24 20 3.0 7.5 55 65 45 55 1/ Not applicable to crimp or shielded contacts. Dielectric withstanding voltage: See
13、 table III. TABLE III. Dielectric withstanding voltage. Altitude Humidity condition All other conditions Sea level 600 1,000 70,000 - 325 Vibration: Test procedure EIA364-28, test condition IV. Temperature cycling: Test procedure EIA364-32, condition 1, 5 cycles, except temperature shall be -55C to
14、125C. 037Z3 89082 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVB PAGE4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Approved sources of supply are listed herein. Additional sources will be added as they beco
15、me available. The vendors listed on the requirements drawing have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. Vendor similar PIN 1/ DSCC drawing PIN 2/ 3/ 4/ 5/ CAGE 71468 CAGE 60563 CAGE 28198 CAGE SW884 89082GBEPT 89082GBEST 89082GBEPR 89082GBESR DCMMY17W
16、5PA101 DCMMY17W5SA101 DCMM17W5PA101 DCMM17W5SA101 P175PSA2D P175RSA2D P175PSA2 P175RSA2 CBM17W5M02F00C-0 CBM17W5F02F00C-0 CBM17W5M02000C-0 CBM17W5F02000C-0 PDMMHW36W4P PCMMHW36W4S PCMMW36W4P PCMMW36W4P 1/ Caution. Do not use this number for item acquisition. Items acquired to this number may not sat
17、isfy the performance requirements of this drawing. 2/ Connectors supplied to this drawing shall include a full complement of signal contacts. 3/ Size 8 contacts should be ordered separately. 4/ Size 8 contacts are snap-in and removable. 5/ For size 8 contacts, see DSCC drawings 89046 through 89061.
18、Vender CAGE Vendor name number and address 28198 Positronics Industries, Incorporated 423 North Campbell Springfield, MO 65801-8247 60563 The Phoenix Company 555 Pond Drive Wood Dale, IL 60191-1192 71468 ITT Cannon P.O. Box 929 666 East Dyer Road Santa Ana, CA 92702-0929 SW884 The Phoenix Company of Chicago, Mexico Carretera Internacional K M 1969 Guadalajara Nogales KM 2 Empalme, Mexico 85340 037Z3 89082 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVB PAGE5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
