1、REVISIONS LTR DESCRIPTION DATE APPROVED A Update format. Correcting references. Correcting address list of sources. 16 July 02 Robert Heber Prepared in accordance with ASME Y14.100 REV PAGE REV A A A A A REV STATUS OF PAGES PAGE 1 2 3 4 5 PMIC N/A PREPARED BY Jeffery Tunstall DEFENSE SUPPLY CENTER,
2、COLUMBUS COLUMBUS, OHIO 43216-5000 CHECKED BY Abdo Abdouni APPROVED BY Robert Heber TITLE CONNECTOR ACCESSORIES, ELECTRICAL, SHORTING CAP BACKSHELL, ENVIRONMENTAL, CATEGORY 4C OF MIL-C-85049, FOR USE WITH MIL-C-5015 CRIMP, MIL-C-26482 SERIES 2, SAE-AS81703, AND MIL-DTL-83723 SERIES III CONNECTOR SIZ
3、E CAGE CODE 037Z3 DWG. NO. 93031 Original date of drawing 12 October 1993 A REV A PAGE 1 OF 5 AMSC N/A 5935-E673 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CA
4、GE CODE DWG NO. 037Z3 93031 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 2 FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 93031 DEFENSE SUPPLY CENTER, COLUM
5、BUS COLUMBUS, OH 43216-5000 A REV A PAGE 3 Shell size. For connector shell size (ref) Dash number SAE-AS81703 series III MIL-C-26482 series II and MIL-DTL-83723 series III MIL-C-5015 crimp B dia max C dia max 3 3 - - - - - - 18.3 (0.72) 19.6 (0.77) 8 - - - 8 8S 16.5 (0.65) 16.5 (0.65) 10 - - - 10 10
6、S, 10SL 19.6 (0.77) 19.6 (0.77) 12 7 12 12s, 12 23.1 (0.91) 23.9 (0.94) 14 12 14 14s, 14 26.2 (1.03) 27.2 (1.07) 16 19 16 16s, 16 29.2 (1.15) 30.7 (1.21) 18 27 18 18 31.0 (1.22) 31.2 (1.23) 20 37 20 20 34.0 (1.34) 34.5 (1.36) 22 - - - 22 22 37.3 (1.47) 37.6 (1.48) 24 - - - 24 24 40.4 (1.59) 43.9 (1.
7、73) 28 - - - - - - 28 50.0 (1.97) 50.0 (1.97) 32 - - - - - - 32 57.9 (2.28) 56.4 (2.22) 36 - - - - - - 36 64.3 (2.53) 62.7 (2.47) 40 - - - - - - 40 70.6 (2.78) 69.1 (2.72) 44 - - - - - - 44 77.0 (3.03) 75.4 (2.97) 48 - - - - - - 48 81.8 (3.22) 81.8 (3.22) 61 - - - - - - - - - 42.2 (1.66) 42.4 (1.67)
8、 Fastener size. Fastener size E 0.13 (.005) A 3.6 (.140) B 4.2 (.167) C 4.6 (.182) D 4.9 (.191) E 3.2 (.125) N No fastener NOTES: 1. Dimensions are in millimeters. 2. Inch-pound equivalents are in parentheses. 3. Dimensions apply after plating. 4. The U.S. Government preferred a system of measuremen
9、ts is the metric SI system. However, since this item was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. FIGURE 1. Dimensions and configuration Continued. Provided by IHSNot for R
10、esaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 93031 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 4 REQUIREMENTS: Shall be in accordance with MIL-C-85049, category 4C, excluding cable pullout. Fastener tensile strength:
11、Both axial and longitudinal directions shall be 25 pounds. The load shall be applied to the end of the rope. Design and construction: See figure 1. Interface dimensions shall conform to MIL-C-85049, accessory intermateability data for MIL-C-5015 crimp, MIL-C-26482 series 2, SAE-AS81703 series 3, and
12、 MIL-DTL -83723 series III connectors. Material: Accessory components: Aluminum alloy shall be in accordance with Mil-C-85049. O-ring: Shall be in accordance with MIL-C-85049. Rope: Stainless steel, passivated, with insulating jacket. Fastener: Stainless steel, passivated. Body strap: Stainless stee
13、l, passivated. Finish: A, N, and W shall be in accordance with MIL-C-85049. Finish N is for space applications only. Part or Identifying Number (PIN): The PIN shall be in accordance with the following: Example: 93031- 1 W 11 C 2 5 Drawing number Type Finish Shell size (see figure1) Fastener size (se
14、e figure 1) N = No fastener Attachment Length 12.7 mm 6.4 mm (.50 inch .25) increments; e.g., 6 = 76.2 mm (3.00 inches) Accessory Length 12.7 mm 6.4 mm (.50 inch .25) increments; e.g., 5 = 63.5 mm (2.50 inches), 25.4 mm (1.00 inch) minimum length. N = No attachment Marking: Marking shall be in accor
15、dance with MIL-C-85049, except the PIN shall be as stated above. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 93031 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 5 QUALIFICATION: Qualification in
16、spection: Qualification inspection for the adapter specified herein shall not be required. Qualification conformance inspection: Shall be in accordance with MIL-C-85049. Inspection of packaging: Shall be in accordance with MIL-C-85049. Methods of inspection: Shall be in accordance with MIL-C-85049.
17、Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed herein have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. DSCC drawing PIN Vendor CAGE number 31461 06324 0
18、7418 93031-*-* 1/ A5416B* A5416S* 340AS001*-* 340AS002*-* S3994C*-*-* 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Vendor CAGE Vendor name number and address 31461 Electro Adapter, Incorporated 20640 Nordhoff Street Chatsworth, CA 91311 06324 Glenair, Incorporated 1211 Air Way Glendale, CA 91201-2497 07418 Sunbank Electronics, Incorporated 1740 Commerce Way Paso Robles, CA 93446 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
