1、 REVISIONS LT DESCRIPTION DATE APPROVED A Add additional part numbers per request of users. 30 March 99 Howard H. Jenkins B Add three percent lead requirement to lead finish paragraph. 23 June 04 Kendall Cottongim C Add -29 part per request of user 22 December 04 Kendall Cottongim D Add new manufact
2、urer and part numbers. 27 April 05 Kendall Cottongim E Add new manufacturer and part numbers. 18 April 07 Michael Radecki F Add new manufacturer and part numbers 6 June 08 Michael Radecki Prepared in accordance with ASME Y14.100-2000 Selected item drawing REV STATUS OF PAGES REV F F F F F F F F F PA
3、GES 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY Edward H. Back DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing 9 August 1995 CHECKED BY Edward H. Back TITLE CAPACITOR, FIXED, TANTALUM CHIP, LOW ESR APPROVED BY David E. Moore SIZE A CODE IDENT. NO. 037Z3 DWG NO. 95158 REV F PAGE 1 OF
4、 9 AMSC N/A 5910-E415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 95158 REV F PAGE
5、 2 1. SCOPE 1.1 Scope. This drawing describes the complete requirements for low ESR tantalum chip capacitors. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 95158- 01 K H Drawing number Dash number Capacitance tolerance Termination finish (see table I) K = 10 percent B =
6、 Gold plated (10 microinch minimum) M = 20 percent H = solder plated (100 microinch minimum) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications standards and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified her
7、ein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-55365 - Capacitor, Fixed, Electrolytic (Tantalum), Chip, Established Reliability and Nonestablished Reliability, General Specification for. STAN
8、DARDS DEPARTMENT OF DEFENSE MIL-STD-202 - Test Methods for Electronic and Electrical Component Parts. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil/ from the Standardiz
9、ation Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes a
10、pplicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified herein (see figure 1). 3.1.1 Terminations. Chip capacitors shall have gold plated or solder plated terminat
11、ions (see 1.2 and figure 1). The solder plated terminations shall be solderable when tested in accordance with MIL-STD-202, method 208. Tin plating is prohibited as a final finish or as an undercoat. Tin-lead (Sn-Pb) finishes are acceptable provided that the minimum lead content is three percent. 3.
12、1.2 Operating temperature range. The capacitors are rated for their given voltages from -55C to +85C. They are derated two thirds of their given voltages at +125C. See table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, CO
13、LUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 95158 REV F PAGE 3 Dimensions Case code L 0.3 ( .012) W 0.3 ( .012) H 0.3 ( .012) C 6.0 (.236) 3.2 (.126) 2.5 (.098) D 7.3 (.287) 4.3 (.169) 2.8 (.110) X 7.3 (.287) 4.3 (.169) 4.0 (.157) Dimensions (reference only) (see note 7) Case code K 0.
14、20 ( .008) F 0.1 ( .004) S 0.3 ( .012) B 0.15 ( .006) X 0.10 ( .004) C 1.4 (.055) 2.2 (.087) 1.3 (.051) 0.5 (.020) 0.10 (.004) D 1.5 (.059) 2.4 (.094) 1.3 (.051) 0.5 (.020) 0.10 (.004) X 2.3 (.091) 2.4 (.094) 1.3 (.051) 0.5 (.020) 0.10 (.004) Dimensions (reference only) (see note 7) Case code P R T
15、A G E C 0.9 (.035) 1.0 (.039) 0.13 (.005) 3.1 (.122) 2.8 (.110) 2.4 (.094) D 0.9 (.035) 1.0 (.039) 0.13 (.005) 3.8 (.150) 3.5 (.138) 3.5 (.138) X 1.7 (.067) 1.0 (.039) 0.13 (.005) 3.8 (.150) 3.5 (.138) See note 6 3.5 (.138) See note 6 Provided by IHSNot for ResaleNo reproduction or networking permit
16、ted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 95158 REV F PAGE 4 NOTES: 1. Dimensions are in millimeters. 2. Inch equivalents are in parentheses and are given for information only. 3. The anode (+) terminal shall be indicated by t
17、he bevel on the anode end. 4. Solderable surfaces are only those surfaces designated as such. Termination edges are not considered solderable. 5. Notch at option of the manufacturer. 6. At the option of the manufacturer, this area may be a round glue pad, 2.9 0.1 (.114 .004) in diameter. 7. Referenc
18、e dimensions may vary by manufacturer. Contact manufacturer for exact dimensions. FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG N
19、O. 95158 REV F PAGE 5 TABLE I. Electrical characteristics. DC leakage (max) uA Dissipation factor (max) % DSCC drawing 95158- 1/ Cap. (nom) uF +25C +85C +125C +25C +85C +125C -55C Max ESR 100 kHz +25C Ohms Case code 6 V dc at 85C 4 V dc at 125C 8 V dc surge at 85C 01- 02- 03- 25- 68 150 220 220 3.3
20、7.2 13.2 13.2 19.8 43.2 132 132 33 72 165 165 4 6 8 8 6 8 12 12 6 8 12 12 0.175 0.125 0.100 0.100 D X X D 10 V dc at 85C 7 V dc at 125C 13 V dc surge at 85C 04- 05- 06- 07- 08- 26- 28- 47 68 100 100 150 150 220 3.8 5.4 10 8 15 15 15 22.8 32.4 100 48 150 150 150 38 54 125 80 187.5 187.5 187.5 4 4 8 6
21、 8 8 8 6 6 12 8 12 12 12 6 6 12 8 12 12 12 0.200 0.150 0.100 0.100 0.100 0.100 0.100 D X D X X D X 16 V dc at 85C 10 V dc at 125C 20 V dc surge at 85C 09- 10- 11- 33 47 100 4.2 7.5 16 25.2 75 160 42 94 200 4 6 8 6 9 12 6 9 12 0.250 0.200 0.125 D D X 20 V dc at 85C 13 V dc at 125C 26 V dc surge at 85
22、C 12- 13- 14- 15- 15 22 47 68 2.4 3.5 7.5 13.6 14.4 21 45 136 24 35 75 170 4 4 4 6 6 6 6 9 6 6 6 9 0.275 0.275 0.150 0.150 D D X X 25 V dc at 85C 17 V dc at 125C 32 V dc surge at 85C 16- 17- 18- 19- 15 15 22 33 3.8 3 4.4 6.6 38 18 26.4 39.6 46.9 30 44 66 6 4 4 4 9 6 6 6 9 6 6 6 0.275 0.200 0.225 0.1
23、75 D X X X 35 V dc at 85C 23 V dc at 125C 46 V dc surge at 85C 29- 20- 27- 21- 22- 23- 4.7 6.8 10 10 15 22 1.7 1.9 3.5 2.8 5.3 7.7 10.2 11.4 35 16.8 53 77 17 19 42 28 65.6 96.3 6 4 4 4 6 6 9 6 6 6 9 9 9 6 6 6 9 9 0.600 0.300 0.300 0.250 0.225 0.300 C X D X X X 50 V dc at 85C 33 V dc at 125C 65 V dc
24、surge at 85C 24- 4.7 1.9 11.4 19 4 6 6 0.300 X Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 95158 REV F PAGE 6 3.2 Electrical characteristics. 3.2.1 Capacitance. Se
25、e table I. Measured in accordance with method 305 of MIL-STD-202. Maximum dc bias shall be 2.2 volts for all ac measurements. The frequency of the ac voltage shall be 120 5 Hz and the magnitude shall be limited to 1.0 volt rms. 3.2.2 Capacitance tolerance. K = 10 percent, M = 20 percent. 3.2.3 Rated
26、 voltage. The rated voltage shall be in accordance with table I. Above +85C, voltage derating is required (see MIL-PRF-55365). 3.3 Surge current. Surge current shall be performed on a 100 percent basis before or after the group A (exponential distribution) voltage aging test of MIL-PRF-55365. Capaci
27、tors shall be subjected to four consecutive cycles under the following conditions: a. Temperature: +25C 5C. b. Applied voltage: Rated dc voltage 2 percent from a power source having an energy storage bank of 50,000 uF (minimum) across the output terminals. c. Charge cycle: 4 seconds maximum. d. Disc
28、harge cycle: 4 seconds maximum to a voltage below 1 percent of rated voltage. e. The total dc resistance (excluding the capacitor) including the wiring, fixturing, and output impedance of the regulated power supply to each test position during the charging cycle shall be 0.6 ohm maximum. f. On compl
29、etion of the test, the capacitors shall meet the following requirements: DCL: See table I. Cap.: Shall meet the initial measured value. DF: See table I. 3.4 Additional tests. The following additional tests shall be performed at the option of the user (see 6.2b) and shall be negotiable with the manuf
30、acturer. 3.4.1 Vibration, high frequency. The capacitors shall meet the requirements of MIL-PRF-55365 when tested in accordance with test condition D, method 204 of MIL-STD-202. 3.4.2 Thermal shock. Thermal shock shall be in accordance with MIL-PRF-55365 when tested for five cycles. 3.4.3 Solderabil
31、ity. Solderability shall be in accordance with MIL-PRF-55365. 3.4.4 Surge voltage. Surge voltage shall be in accordance with MIL-PRF-55365. 3.4.5 Moisture resistance. Moisture resistance shall be in accordance with MIL-PRF-55365. 3.4.6 Stability at low and high temperatures. Stability at low and hig
32、h temperatures shall be in accordance with MIL-PRF-55365. 3.4.7 Resistance to soldering heat. Resistance to soldering heat shall be in accordance with MIL-PRF-55365. 3.4.8 Life. A minimum of dc rated voltage at 85C or a minimum of derated voltage per MIL-PRF-55365 at 125C for 2000 hours. 3.5 Recycle
33、d, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycl
34、e costs. 3.6 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a approved source of supply. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE
35、 A CODE IDENT NO. 037Z3 DWG NO. 95158 REV F PAGE 7 3.7 Marking. Marking shall be in accordance with MIL-PRF-55365, except the “JAN“ or “J“ brand and the failure rate level symbol do not apply and shall not be marked on the capacitor or any packaging. 3.8 Workmanship. Capacitors shall be uniform in q
36、uality and free from defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Sampling and inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the surg
37、e current test and the group A inspection (exponential distribution), subgroups 1 and 3, of MIL-PRF-55365, except that the voltage aging shall be for a minimum of 10 hours. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order
38、 (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within
39、 the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES 6.1 Inte
40、nded use. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. This drawing is intended exclusively to prevent the proliferation of unnecessar
41、y duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order should s
42、pecify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.3 User
43、s of record. Coordination of this document for future revisions are coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: Defense Supply Center, Columbus, ATTN: DSCC/VAT, Post Of
44、fice Box 3990, Columbus, OH 43218-3990 or e-mailed to capacitorfilterdla.mil also by telephone (614) 692-0563 or DSN 850-0563. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3
45、DWG NO. 95158 REV F PAGE 8 6.4 Similar vendor types. See table II. TABLE II. Similar vendor types. DSCC drawing 95158- Similar vendor PIN A 1/ Similar vendor PIN B 1/ Similar vendor PIN C 1/ 01- T495D686-006A- 593D686X-6R3D- TBJD686-006C-DZ0-23 02- T495X157-006A- 593D157X-6R3E- TBJE157-006C-DZ0-23 0
46、3- T495X227-006A- 593D227X-6R3E- TBJE227-006L-DZ0-23 04- T495D476-010A- 593D476X-010D- TBJD476-010C-DZ0-23 05- T495X686-010A- 593D686X-010E- TBJE686-010C-DZ0-23 06- T495D107-010A- 593D107X-010D- TBJD107-010C-DZ0-23 07- T495X107-010A- 593D107X-010E- TBJE107-010C-DZ0-23 08- T495X157-010A- 593D157X-010
47、E- TBJE157-010C-DZ0-23 09- T495D336-016A- 593D336X-016D- TBJD336-016C-DZ0-23 10- T495D476-016A- 593D476X-016D- TBJD476-016C-DZ0-23 11- T495X107-016A- 593D107X-016E- TBJE107-016C-DZ0-23 12- T495D156-020A- 593D156X-020D- TBJD156-020C-DZ0-23 13- T495D226-020A- 593D226X-020D- TBJD226-020C-DZ0-23 14- T49
48、5X476-020A- 593D476X-020E- TBJE476-020C-DZ0-23 15- T495X686-020A- 593D686X-020E- TBJE686-020L-DZ0-23 16- T495D156-025A- 593D156X-025D- TBJD156-025C-DZ0-23 17- T495X156-025A- 593D156X-025E- N/A 18- T495X226-025A- 593D226X-025E- TBJE226-025L-DZ0-23 19- T495X336-025A- 593D336X-025E- TBJE336-025C-DZ0-23 20- T495X685-035A- 593D685X-035E- N/A 21- T495X106-035A- 593D106X-035E- TBJE106-035C-DZ0-23 22- T495X156-035A- 593D156X-035E- TBJE156-035C-DZ0-23 23- T495X226-035A- 593D226X-035E- TBJE226-035C-DZ0-23 24- T495X475-050A- 593D475
