1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add new device type 09. Update boilerplate to current requirements. Corrections throughout. - CFS 06-12-11 Thomas M. Hess E Update boilerplate paragraphs to current requirements. - phn 12-02-14 Thomas M. Hess CURRENT DESIGN ACTIVITY CAGE CODE 16236 HAS CHAN
2、GED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV B B B B B B B B B B B PAGE 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Phu H. Nguyen DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 432
3、18-3990 Original date of drawing YY-MM-DD CHECKED BY Phu H. Nguyen TITLE MICROCIRCUIT, LINEAR, ULTRALOW-NOISE, HIGH PSRR, FAST RF 200-mA LOW-DROPOUT LINEAR REGULATORS, MONOLITHIC SILICON 03-06-18 APPROVED BY Thomas M. Hess SIZE A CODE IDENT. NO. 16236 DWG NO. V62/03634 REV B PAGE 1 OF 11 AMSC N/A 59
4、62-V027-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03634 REV B PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of ultralow-noise
5、, high PSRR, fast RF 200 mA, low dropout linear regulators, with an operating junction temperature range of -40C to +125C for device types 01 through 08, and an operating junction temperature range of -55C to +125C for device type 09. 1.2 Vendor Item Drawing Administrative Control Number. The manufa
6、cturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/03634 01 Y E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). 1/
7、 Device Generic Output Circuit function Type voltage 01 TPS79301-EP +1.2 V to 5.5 V Ultra low noise, high PSRR, fast RF 200 mA low dropout linear regulator. 02 TPS79318-EP +1.8 V Ultra low noise, high PSRR, fast RF 200 mA low dropout linear regulator. 03 TPS79325-EP +2.5 V Ultra low noise, high PSRR
8、, fast RF 200 mA low dropout linear regulator. 04 TPS79328-EP +2.8 V Ultra low noise, high PSRR, fast RF 200 mA low dropout linear regulator. 05 TPS793285-EP +2.85 V Ultra low noise, high PSRR, fast RF 200 mA low dropout linear regulator. 06 TPS79330-EP +3.0 V Ultra low noise, high PSRR, fast RF 200
9、 mA low dropout linear regulator. 07 TPS79333-EP +3.3 V Ultra low noise, high PSRR, fast RF 200 mA low dropout linear regulator. 08 TPS793475-EP +4.75 V Ultra low noise, high PSRR, fast RF 200 mA low dropout linear regulator. 09 TPS79301-EP +1.2 V to 5.5 V Ultra low noise, high PSRR, fast RF 200 mA
10、low dropout linear regulator. 1.2.2 Case outline(s). The case outlines are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 6 JEDEC MO-178 Plastic small outline Y 5 JEDEC MO-178 Plastic small outline 1.2.3 Lead finishes. The lead finishes are as specified below or othe
11、r lead finishes as provided by the device manufacturer: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other _ 1/ Users are cautioned to review the manufacturers data manual for additional user information relating to these devices. Pro
12、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03634 REV B PAGE 3 1.3 Absolute maximum ratings. 1/ Input voltage range (VI) . -0.3 V to +6.0 V 2/ Voltage range at EN
13、 . -0.3 V to VI + 0.3 V Voltage on OUT . -0.3 V to +6.0 V Peak output current Internally limited ESD rating, HBM 2 kV ESD rating, CDM 500 V Continuous total power dissipation See dissipation rating table Operating virtual junction temperature range (TJ): Device types 01 through 08 . -40C to 125C Dev
14、ice type 09 . -55C to 125C Storage temperature range (TSTG) . -65C to 150C Dissipation Rating Table Ambient Temperatures Board Case outline RJCRJADerating factor Above TA= 25C TA 25C Power rating TA= 70C Power rating TA= 85C Power rating Low K 3/ X, Y 63.75C/W 256C/W 3.906 mW/C 391 mW 215 mW 156 mW
15、High K 4/ X, Y 63.75C/W 178.3C/W 5.609 mW/C 561 mW 308 mW 224 mW 2. APPLICABLE DOCUMENTS JEDEC SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC) JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Copies of these documents are available online at http:/www.jedec.org or from JEDEC Solid
16、 State Technology Association, 3103 North 10th Street, Suite 240S, Arlington, VA 22201.) 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions be
17、yond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ All voltage values are with respect to network terminal ground. 3/ The JEDEC low K (1s) board design used to derive this
18、data was a 3-inch x 3-inch, two layer board with 2 ounce copper traces on top of the board. 4/ The JEDEC high K (2s2p) board design used to derive this data was a 3-inch x 3-inch, multilayer board with 1 ounce internal power and ground planes and 2 ounce copper traces on top and bottom of the board.
19、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03634 REV B PAGE 4 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacture
20、rs part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical
21、 characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3
22、.5.1 Case outlines. The case outlines shall be as shown in 1.2.2 and on figure 1. 3.5.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.5.3 Block diagrams. The block diagrams shall be as specified on figure 3. Provided by IHSNot for ResaleNo reproduction or networ
23、king permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03634 REV B PAGE 5 TABLE I. Electrical performance characteristics. 1/ Test Test conditions Devices 01 08: TJ= -40C to 125C Device 09: TJ= -55C to 125C VI= VO(Typ)+ 1 V,
24、 IO= 1 mA, EN = VI, CO= 10 F, C(byp)= 0.01 F unless otherwise specified Device type Limits Unit Min Max Input voltage, VI2/ All 2.7 5.5 V Continuous output current, IO3/ All 0 200 mA Operating junction temperature, TJ01 - 08 -40 125 C 09 -55 125 Output voltage 0 A IO 200 mA, 1.22 V VO 5.2 V 4/ 01 0.
25、98 VO 1.02 VO V TJ= 25C 02 1.8 Typ 0 A IO 200 mA, 2.8 V VI 5.5 V 1.764 1.836 TJ= 25C 03 2.5 Typ 0 A IO 200 mA, 3.5 V VI 5.5 V 2.450 2.550 TJ= 25C 04 2.8 Typ 0 A IO 200 mA, 3.8 V VI 5.5 V 2.744 2.856 TJ= 25C 05 2.85 Typ 0 A IO 200 mA, 3.85 V VI 5.5 V 2.793 2.907 TJ= 25C 06 3.0 Typ 0 A IO 200 mA, 4.0
26、V VI 5.5 V 2.94 3.06 TJ= 25C 07 3.3 Typ 0 A IO 200 mA, 4.3 V VI 5.5 V 3.234 3.366 TJ= 25C 08 4.75 Typ 0 A IO 200 mA, 5.25 V VI 5.5 V 4.655 4.845 0 A IO 200 mA, 1.22 V VO 5.2 V 4/ 09 0.97 VO 1.025 VO Quiescent current (GND current) 0 A IO 200 mA, TJ= 25C All 170 Typ A 0 A IO 200 mA, All 220 Load regu
27、lation 0 A IO 200 mA, TJ= 25C All 5.0 Typ mV Output voltage line regulation (VO/VO) 5/ VO+ 1 V VI 5.5 V, TJ= 25C All 0.05 Typ %/V VO+ 1 V VI 5.5 V 0.12 Output noise voltage BW = 200 Hz to 100 kHz, IO= 200 mA, TJ= 25C C(byp)= 0.001 F 04 55 Typ VRMSC(byp)= 0.0047 F 36 Typ C(byp)= 0.01 F 33 Typ C(byp)=
28、 0.1 F 32 Typ Time, start up RL= 14 CO= 1 F, TJ= 25C C(byp)= 0.001 F 04 50 Typ s C(byp)= 0.0047 F 70 Typ C(byp)= 0.01 F 100 Typ Output current limit VO = 0 V 4/ All 285 600 mA Standby current EN = 0 V, 2.7 V VI 5.5 V All 1 A See notes at end of table. Provided by IHSNot for ResaleNo reproduction or
29、networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03634 REV B PAGE 6 TABLE I. Electrical performance characteristics - Continued. 1/ Test Test conditions Devices 01 08: TJ= -40C to 125C Device 09: TJ= -55C to 125C
30、 VI= VO(Typ)+ 1 V, IO= 1 mA, EN = VI, CO= 10 F, C(byp)= 0.01 F unless otherwise specified Device type Limits Unit Min Max High level enable input voltage 2.7 V VI 5.5 V All 2.0 V Low level enable input voltage 2.7 V VI 5.5 V 0.7 V Input current (EN) EN = 0 -1 1 A Input current (FB) FB = 1.8 V 01, 09
31、 1 A Power supply ripple rejection f = 100 Hz, TJ= 25C, IO= 10 mA 04 70 Typ dB f = 100 Hz, TJ= 25C, IO= 200 mA 68 Typ f = 10 kHz, TJ= 25C, IO= 200 mA 70 Typ f = 100 kHz, TJ= 25C, IO= 200 mA 43 Typ Dropout voltage 6/ IO= 200 mA, TJ= 25C 04 120 Typ mV IO= 200 mA 200 IO= 200 mA, TJ= 25C 05 120 Typ IO=
32、200 mA 200 IO= 200 mA, TJ= 25C 06 112 Typ IO= 200 mA 200 IO= 200 mA, TJ= 25C 07 102 Typ IO= 200 mA 180 IO= 200 mA, TJ= 25C 08 77 Typ IO= 200 mA 125 UVLO threshold VCCrising All 2.25 2.65 V UVLO hysteresis VCCrising, TJ= 25C All 100 Typ mV 1/ Testing and other quality control techniques are used to t
33、he extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by ch
34、aracterization and/or design. 2/ To calculate the minimum input voltage for your maximum output current, use the following formula: VI(min) = VO(max) + VDO(max load). 3/ Continuous output current and operating junction temperature are limited by internal protection circuitry, but it is not recommend
35、ed that the device operate under conditions beyond those specified in this table for extended periods of time. 4/ The minimum IN operating voltage is 2.7 V or VO(Typ)+ 1V, whichever is greater. The maximum IN voltage is 5.5 V. The maximum output current is 200 mA. 5/ If VO 2.5 V then Vimin= 2.7 V, V
36、Imax= 5.5 V: Line Reg. (mV) = (%/V) x 100)V7.2V(VaxImOx 1000 If VO 2.5 V then VImin= VO+ 1 V, Vimax= 5.5 V. 6/ IN voltage equals VO(Typ) 100 mV; Device type 03 dropout voltage is limited by the input voltage range limitations. Provided by IHSNot for ResaleNo reproduction or networking permitted with
37、out license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03634 REV B PAGE 7 Case X Notes: 1. All linear dimensions are in millimeters. 2. This drawing is subject to change without notice. 3. Body dimensions do not include mold flash or protrusio
38、ns. 4. Leads 1, 2, 3 may be wider than leads 4, 5, 6 for package orientation. 5. Falls within JEDEC MO-178 variation AB, except minimum lead width. FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMB
39、US COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03634 REV B PAGE 8 Case Y Notes: 1. All linear dimensions are in millimeters. 2. This drawing is subject to change without notice. 3. Body dimensions do not include mold flash or protrusions. 4. Leads 1, 2, 3 may be wider than leads 4, 5 for
40、package orientation. 5. Falls within JEDEC MO-178 variation AA. FIGURE 1. Case outlines - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03634 REV B PA
41、GE 9 Cases X, Y Millimeters Symbol Min Max A 0.95 1.45 A1 0.05 b 0.25 0.50 c 0.15 NOM D 2.80 3.00 E 1.50 1.70 E1 2.60 3.00 e 0.95 Typ L 0.35 0.55 FIGURE 1. Case outline - Continued. Terminal number Case X Case Y Terminal symbol Terminal symbol 1 IN IN 2 GND GND 3 EN EN 4 BYPASS BYPASS 5 FB OUT 6 OUT
42、 FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03634 REV B PAGE 10 FIGURE 3. Block diagrams Provided by IHSNot for ResaleNo repro
43、duction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03634 REV B PAGE 11 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requireme
44、nts as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and
45、 marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is bas
46、ed on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is
47、not to be construed as a guarantee of present or continued availability as a source of supply for the item. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Vendor part number 2/ Symbol V62/03634-01YE 01295 TPS79301DBVREP PGVE V62/03634-02XE 01295 TPS79318DBVREP PHH
48、E V62/03634-03XE 01295 TPS79325DBVREP PGWE V62/03634-04XE 3/ TPS79328DBVREP PGXE V62/03634-05XE 3/ TPS793285DBVREP PHIE V62/03634-06XE 3/ TPS79330DBVREP PGYE V62/03634-07XE 01295 TPS793333DBVREP PHUE V62/03634-08XE 01295 TPS793475DBVREP PHJE V62/03634-09XE 01295 TPS79301MDBVREP PMBM 1/ The vendor item drawing establish
