1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Update boilerplate to current MIL-PRF-38535 requirements. - PHN 13-12-11 Thomas M. Hess CURRENT DESIGN ACTIVITY CAGE CODE 16236 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.24 Vendor item drawing
2、 REV PAGE REV PAGE REV STATUS OF PAGES REV A A A A A A A A A A A PAGE 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Charles F. Saffle DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing CHECKED BY Charles F. Saffle TITLE MICROCIRCUIT, DIGITAL, ADVANCED BIPOLAR CMOS, 16-B
3、IT BUS TRANSCEIVER WITH THREE-STATE OUTPUTS, MONOLITHIC SILICON YY-MM-DD 06-01-17 APPROVED BY Thomas M. Hess SIZE A CODE IDENT. NO. 16236 DWG NO. V62/06609 REV A PAGE 1 OF 11 AMSC N/A 5962-V020-14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFEN
4、SE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06609 REV A PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance 16-bit bus transceiver with three-state outputs microcircuit, with an operating temperature range of -55C to
5、+125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/06609 - 01 X E Drawing Device type Case outline Lead
6、finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 SN74ABT16245A-EP 16-bit bus transceiver with three-state outputs 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package styl
7、e X 48 JEDEC MO-118 Plastic small-outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other 1.3 Absolute max
8、imum ratings. 1/ Supply voltage range (VCC) . -0.5 V to +7 V Input voltage range (except I/O ports) (VI) -0.5 V to +7 V 2/ Voltage applied to any output in the high or power-off state (VO) -0.5 V to +5.5 V Maximum current into any output in the low state (IO) . 96 mA Maximum input clamp current (VI
9、0) (IIK) -18 mA Maximum output clamp current (VO 0) (IOK) -50 mA Package thermal impedance (JA) . 94C/W 3/ Storage temperature range (TSTG) . -65C to 150C 4/ _ 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and
10、 functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ The input and output negative-voltage ratings may
11、be exceeded if the input and output clamp-current ratings are observed. 3/ The package thermal impedance is calculated in accordance with JESD 51. 4/ Long-term high-temperature storage and/or extended use at maximum recommended operating conditions may result in a reduction of overall device life. S
12、ee figure 1 for additional information on thermal derating. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06609 REV A PAGE 3 1.4 Recommended operating conditions
13、. 1/ Supply voltage range (VCC) . 4.5 V to 5.5 V Minimum high-level input voltage (VIH) 2 V Maximum low-level input voltage (VIL) . 0.8 V Input voltage range (VI) . 0 V to VCCMaximum high-level output current (IOH) . -24 mA Maximum low-level output current (IOL) . 48 mA Maximum input transition rise
14、 or fall rate (Outputs enabled) (t/v) 10 ns/V Minimum power-up ramp rate (t/VCC) 200 s/V Operating free-air temperature range (TA) -55C to +125C FIGURE 1. Estimated device life at elevated temperatures. 1/ All unused inputs of the device must be held at VCCor GND to ensure proper device operation. P
15、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06609 REV A PAGE 4 2. APPLICABLE DOCUMENTS JEDEC SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC) JEP95 Registered and Sta
16、ndard Outlines for Semiconductor Devices (Copies of these documents are available online at http:/www.jedec.org or from JEDEC Solid State Technology Association, 3103 North 10th Street, Suite 240S, Arlington, VA 22201-2107). 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked
17、with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) a
18、bove. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified her
19、ein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 2. 3.5.2 Function table. The function table shall be as shown in figure 3. 3.5.3 Logic diagram. The logic diagram shall be as shown in figure 4. 3.5.4 Terminal connections. The terminal connections shall be
20、 as shown in figure 5. 3.5.5 Timing waveforms and test circuit. The timing waveforms and test circuit shall be as shown in figure 6. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO.
21、16236 DWG NO. V62/06609 REV A PAGE 5 TABLE I. Electrical performance characteristics. 1/ Test Symbol Conditions VCCTemperature, TALimits Unit Min Max Input clamp voltage VIKII= -18 mA 4.5 V 25C -1.2 V -55C to +125C -1.2 High level output voltage VOHIOH= -3 mA 4.5 V 25C, -55C to +125C 2.5 V IOH= -3 m
22、A 5 V 25C, -55C to +125C 3 IOH= -24 mA 4.5 V 25C, -55C to +125C 2 IOH= -32 mA 25C 2 Low level output voltage VOLIOL= 48 mA 4.5 V 25C, -55C to +125C 0.55 V IOL= 64 mA 25C 0.55 Hysteresis voltage Vhys5 V 25C 100 TYP mV Input current IIControl inputs, VI= VCCor GND 0 V to 5.5 V 25C, -55C to +125C 1 A A
23、 or B port, VI= VCCor GND 2.1 V to 5.5 V 25C 20 -55C to +125C 100 Three-state output current, power-up IOZPUVO= 0.5 V to 2.7 V, OE= X 0 V to 2.1 V 25C 50 A Three-state output current, power-down IOZPDVO= 0.5 V to 2.7 V, OE= X 2.1 V to 0 V 25C 50 A Three-state output current, high IOZH2/ VO= 2.7 V, O
24、E 2 V 2.7 V to 5.5 V 25C 10 3/ A -55C to +125C 10 Three-state output current, low IOZL2/ VO= 0.5 V, OE 2 V 2.7 V to 5.5 V 25C -10 3/ A -55C to +125C -10 Input/output power-off leakage current IoffVIor VO 5.5 V 0 V 25C 100 A Output high leakage current ICEXVO= 5.5 V, Outputs high 5.5 V 25C, -55C to +
25、125C 50 A Output current IO4/ VO= 2.5 V 5.5 V 25C, -55C to +125C -50 -180 mA Supply current ICCA or B port, VI= VCCor GND, IO= 0, Outputs high 5.5 V 25C, -55C to +125C 2 A or B port, VI= VCCor GND, IO= 0, Outputs low 32 A or B port, VI= VCCor GND, IO= 0, Outputs disabled 2 See footnotes at end of ta
26、ble. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06609 REV A PAGE 6 TABLE I. Electrical performance characteristics - Continued. 1/ Test Symbol Conditions VCCT
27、emperature, TALimits Unit Min Max Supply current delta ICC5/ Data inputs, Outputs enabled, One input at 3.4 V, other inputs at VCCor GND 5.5 V 25C 2 mA -55C to +125C 1.5 Data inputs, Outputs disabled, One input at 3.4 V, other inputs at VCCor GND 25C 0.05 -55C to +125C 1 Control inputs, One input at
28、 3.4 V, other inputs at VCCor GND 25C, -55C to +125C 1.5 Input capacitance CIControl inputs, VI= 2.5 V or 0.5 V 5 V 25C 3 TYP pF Output capacitance COA or B port, VO= 2.5 V or 0.5 V 5 V 25C 6 TYP pF Propagation delay time, from A or B to B or A tPLHCL = 50 pF, See figure 5. 5 V 25C 0.5 3.4 ns 4.5 V
29、to 5.5 V -55C to +125C 0.5 4 Propagation delay time, from A or B to B or A tPHL5 V 25C 0.5 3.8 ns 4.5 V to 5.5 V -55C to +125C 0.5 4.6 Propagation enable time, OE to B or A tPZHCL = 50 pF, See figure 5. 5 V 25C 0.8 5.2 ns 4.5 V to 5.5 V -55C to +125C 0.8 5.5 Propagation enable time, OE to B or A tPZ
30、L5 V 25C 0.9 6.1 4.5 V to 5.5 V -55C to +125C 0.1 7.3 Propagation disable time, OE to B or A tPHZ5 V 25C 1.3 5.8 4.5 V to 5.5 V -55C to +125C 1.3 6.3 Propagation disable time, OE to B or A tPLZ5 V 25C 1.4 4.7 4.5 V to 5.5 V -55C to +125C 1.4 5.5 1/ Testing and other quality control techniques are us
31、ed to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assure
32、d by characterization and/or design. 2/ The parameters IOZHand IOZLinclude the input leakage current. 3/ This limit may vary. 4/ Not more than one output should be tested at a time, and the duration of the test should not exceed one second. 5/ This is the increase in supply current for each input th
33、at is at the specified TTL voltage level, rather than VCCor GND. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06609 REV A PAGE 7 Case X Dimensions Symbol Inches
34、 Millimeters Symbol Inches Millimeters Min Max Min Max Min Max Min Max A - 0.110 - 2.79 E1 0.291 0.299 7.39 7.59 A1 0.008 - 0.20 - e 0.025 BSC 0.635 BSC b 0.008 0.0135 0.203 0.343 L 0.020 0.040 0.51 1.02 D 0.620 0.630 15.75 16.00 L1 0.010 TYP 0.25 TYP E 0.395 0.420 10.03 10.67 L2 0.005 0.010 0.13 0.
35、25 NOTES: 1. All linear dimensions are shown in inches (millimeters). Millimeters equivalents are given for general information only. 2. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0.15). 3. Falls within JEDEC MO-118. FIGURE 2. Case outline. Provided by IHSNot for Re
36、saleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06609 REV A PAGE 8 Inputs Operation OE DIR L L B data to A bus L H A data to B bus H X Isolation H = High voltage level L = Low voltage leve
37、l X = Dont care FIGURE 3. Function table. FIGURE 4. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06609 REV A PAGE 9 Device type: 01 Case outline:
38、 X Terminal number Terminal symbol Terminal number Terminal symbol 1 1DIR 25 2OE 2 1B1 26 2A8 3 1B2 27 2A7 4 GND 28 GND 5 1B3 29 2A6 6 1B4 30 2A5 7 VCC31 VCC8 1B5 32 2A4 9 1B6 33 2A3 10 GND 34 GND 11 1B7 35 2A2 12 1B8 36 2A1 13 2B1 37 1A8 14 2B2 38 1A7 15 GND 39 GND 16 2B3 40 1A6 17 2B4 41 1A5 18 VC
39、C42 VCC19 2B5 43 1A4 20 2B6 44 1A3 21 GND 45 GND 22 2B7 46 1A2 23 2B8 47 1A1 24 2DIR 48 1OE FIGURE 5. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG
40、 NO. V62/06609 REV A PAGE 10 NOTES: 1. CLincludes probe and jig capacitance. 2. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when
41、 disabled by the output control. 3. All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO= 50 , tr 2.5 ns, tf 2.5 ns. 4. The outputs are measured one at a time, with one transition per measurement. FIGURE 6. Timing waveforms and test circuit. Provided by IH
42、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06609 REV A PAGE 11 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspec
43、tion and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, p
44、ackaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data
45、contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(
46、s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all current sources of supply at http:/www.landandmaritime.dla.mil/Programs/Smcr/. Vendor item drawing administrati
47、ve control number 1/ Device manufacturer CAGE code Vendor part number Top side marking V62/06609-01XE 01295 CABT16245AMDLREP ABT16245AMEP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group 8505 Forest Lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without licens
