1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Change top side marking for device type 01, case outline 2 in section 6.3. -phn 08-07-09 Thomas M. Hess B Change thermal resistance for case Y and Z on table I. - phn 08-11-19 Thomas M. Hess Prepared in accordance with ASME Y14.24 Vendor item drawing REV PA
2、GE REV PAGE REV B B A REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Phu H. Nguyen DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO Original date of drawing YY MM DD CHECKED BY Phu H. Nguyen APPROVED BY Thomas M. Hess TITLE MICROCIRCUIT, LINEAR, 1.8 V, MICROPOWER CMOS OPERATIONAL A
3、MPLIFIERS ZERO-DRIFT SERIES, MONOLITHIC SILICON SIZE A CODE IDENT. NO. 16236 DWG NO. V62/07633 07-05-02 REV B PAGE 1 OF 10 AMSC N/A 5962-V006-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A COD
4、E IDENT NO. 16236 DWG NO. V62/07633 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance 1.8 V, micropower CMOS operational amplifiers zero-drift series microcircuit, with an operating temperature range of -55C to +125C. 1.2 Vendor Item Drawing Adminis
5、trative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/07633 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2)
6、(See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 OPA333A-EP 1.8 V, micropower CMOS operational amplifiers zero-drift series 02 OPA2333A-EP Dual, 1.8 V, micropower CMOS operational amplifiers zero-drift series 1.2.2 Case outline(s). The case outlines are as specified herein.
7、Outline letter Number of pins JEDEC PUB 95 Package style X 5 MO-178 Plastic small outline Y 5 MO-203 Plastic small outline Z 8 MO-012 Plastic small outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture: Finish designator Ma
8、terial A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07633 REV PAGE 3 1
9、.3 Absolute maximum ratings. 1/ Maximum supply voltage 7.0 V Signal input terminals, voltage . -0.3 V to (V+) + 0.3 V 2/ Output short circuit . Continuous 3/ Operating temperature range . -55C to 125C Storage temperature range -65C to 150C 4/ Maximum junction temperature 150C ESD rating: Human body
10、model . 4000 V Charged device model 1000 V 2. APPLICABLE DOCUMENTS JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industry Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or at http:/www.jedec.org) 3. R
11、EQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with
12、 the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension.
13、 The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. 3.5.3 Logic diagram. The logic diagram shall be
14、as shown in figure 3. 1/ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is n
15、ot implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ Input terminals are diode clamped to the power-supply rails. Input signals that can swing more than 0.3 V beyond the supply rails should be current limited to 10 mA or less. 3/ Short circ
16、uit to ground, one amplifier per package. 4/ Long-term high temperature storage and/or extended use at maximum recommended operating conditions may result in a reduction of overall device life. See manufacturer data for additional information on enhanced plastic packaging. Provided by IHSNot for Res
17、aleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07633 REV PAGE 4 TABLE I. Electrical performance characteristics. 1/ Limits Test Symbol Conditions 2/ unless otherwise specified Min Max Unit
18、 Offset Voltage Input offset voltage VOSVS= 5 10 V over temperature -55C TA 125C 22 V vs temperature dVOS/dT-55C TA 125C , VS = 1.8 V to 5.5 V 0.02 Typ V/C vs Power supply PSRR -55C TA 125C 6 V/V Long term stability 3/ 3/ Channel separation, dc 0.1 Typ V/V Input bias current Input bias current IB200
19、 pA over temperature -55C TA 125C 150 Typ pA Input offset current IOS400 pA Noise Input voltage noise f = 0.01 Hz to 1 Hz 0.3 Typ VPPInput voltage noise f = 0.1 Hz to 10 Hz 1.1 Typ VPPInput current noise inf = 10 Hz 100 Typ fA/ Hz Input voltage range Common mode voltage range VCM(V-)-0.1 (V+)+0.1 V
20、Common mode rejection ratio CMRR -55C TA 125C , (V-)-0.1 V VCM (V+)+0.1 V 102 dB Input capacitance Differential 2 Typ Common mode 4 Typ pF Open loop gain Open loop voltage gain AOL(V-)+100 mV VO (V+)-100 mV, RL= 10 k, -55C TA 125C 104 dB Frequency response Gain bandwidth product GBW CL= 100 pF 350 T
21、yp kHz Slew rate SR G =1 0.16 Typ V/s Output Voltage output swing from rail RL= 10 k 50 mV over temperature RL= 10 k, -55C TA 125C 85 mV Short circuit current ISC 5 Typ mA Capacitive load drive CL 4/ Open loop output impedance f = 350 kHz, IO= 0 2 Typ k See footnotes at end of table. Provided by IHS
22、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07633 REV B PAGE 5 TABLE I. Electrical performance characteristics Continued. Limits Test Symbol Conditions 2/ unless otherwise sp
23、ecified Min Max Unit Power supply Specified voltage range VS1.8 5.5 V Quiescent Current per Amplifier IQIO= 0 25 A over temperature 30 A Turn on time VS= 5 V 100 Typ s Temperature range Specified range -55 125 C Operating range -55 125 C Storage range -65 150 C Thermal resistance, case X 200 Typ The
24、rmal resistance, case Y 250 Typ Thermal resistance, case Z JA150 TyC/W 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range a
25、nd all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ -55C TA 125C. At TA= 25C, RL= 10 k connected to VS/2, VCM= VS/2, and VOUT= VS/2 unless otherwise noted. 3/ 300-hour life test at 150C d
26、emonstrated randomly distributed variation of approximately 1 V. 4/ See typical characteristic from manufacturer data. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO.
27、V62/07633 REV PAGE 6 Case X Dimension Millimeters Millimeters Symbol Min Max Symbol Min Max A 1.45 E 1.45 1.75 A1 0.00 0.15 E1 2.60 3.00 b 0.30 0.50 e 0.95 NOM c 0.08 0.22 L 0.30 0.55 D 2.75 3.05 NOTES: 1. All linear dimensions are in millimeters. 2. This drawing is subject to change without notice.
28、 3. Body dimensions do not include mold flash or protrusion. Mold flash and protrusion shall not to exceed 0.15 mm per side. 4. Falls within JEDEC MO-178 variation AA. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SU
29、PPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07633 REV PAGE 7 Case Y Dimension Millimeters Millimeters Symbol Min Max Symbol Min Max A 0.80 1.10 E 1.10 1.40 A1 0.00 0.10 E1 1.80 2.40 b 0.15 0.30 e 0.65 NOM c 0.08 0.22 L 0.26 0.46 D 1.85 2.15 NOTES: 1. All linear dimen
30、sions are in millimeters. 2. This drawing is subject to change without notice. 5. Body dimensions do not include mold flash or protrusion. Mold flash and protrusion shall not to exceed 0.15 mm per side. 6. Falls within JEDEC MO-203 variation AA. FIGURE 1. Case outline - Continued. Provided by IHSNot
31、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07633 REV PAGE 8 Case Z Dimension Millimeters Inches Millimeters Inches Symbol Min Max Min Max Symbol Min Max Min Max A 1.75 .069 E 3
32、.80 4.00 .150 .157 A1 0.10 0.25 .004 .010 E1 5.80 6.20 .228 .244 b 0.31 0.51 .012 .020 e 1.27 NOM .050 NOM c 0.17 0.25 .007 .010 L 0.40 1.27 .016 .050 D 4.80 5.00 .189 .197 NOTES: 1. All linear dimensions are in inch (millimeters). 2. This drawing is subject to change without notice. 3. Body length
33、does not include mold flash, protrusion, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed .006 inches (0.15 mm ) per end. 4. Body width does not include interlead flash. Interlead flash shall not exceed .017 inch (0.43 mm) per side. 5. Reference JEDEC MS-012 variation AA. FIGUR
34、E 1. Case outline - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07633 REV PAGE 9 Case X Case Y Case Z Terminal number Terminal symbol Terminal numbe
35、r Terminal symbol Terminal number Terminal symbol 1 OUT 1 +IN 1 OUT A 2 V- 2 V- 2 -IN A 3 +IN 3 -IN 3 +IN A 4 -IN 4 OUT 4 V- 5 v+ 5 V+ 5 +IN B 6 -IN B 7 OUT B 8 V+FIGURE 2. Terminal connections. FIGURE 3. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without lic
36、ense from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/07633 REV A PAGE 10 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal document
37、ation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the ma
38、nufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the de
39、vice manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of prese
40、nt or continued availability as a source of supply for the item. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Vendor part number Top side marking V62/07633-01XE 01295 OPA333AMDBVREP OBYM V62/07633-01YE 01295 OPA333AMDCKREP CHQ V62/07633-02ZE 01295 OPA2333AMDREP
41、2333EP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group 8505 Forest lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
