1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Charles F. Saffle DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing YY-MM-D
2、D CHECKED BY Phu H. Nguyen APPROVED BY Charles F. Saffle TITLE MICROCIRCUIT, DIGITAL, PROGRAMMABLE DIGITAL TEMPERATURE SENSOR, MONOLITHIC SILICON SIZE A CODE IDENT. NO. 16236 DWG NO. V62/09607 09-02-09 REV PAGE 1 OF 11 AMSC N/A 5962-V013-09Provided by IHSNot for ResaleNo reproduction or networking p
3、ermitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09607 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance programmable digital temperature sensor microcircuit, with an operat
4、ing temperature range of -55C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/09607 - 01 X E Drawi
5、ng Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 TMP122-EP Programmable digital temperature sensor 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins JEDEC P
6、UB 95 Package style X 6 MO-178-AB Plastic small outline package 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z
7、Other Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09607 REV PAGE 3 1.3 Absolute maximum ratings. 1/ Power supply voltage (V+) . 7.0 V Input voltage range (VIN)
8、 -0.3 V to 7.0 V Input current . 10 mA Operating temperature range (TA) -55C to +150C Storage temperature range (TSTG) -60C to 150C Maximum junction temperature (TJ) . 150C Leading temperature (soldering) 300C 1.4 Recommended operating conditions. 2/ Supply voltage range (V+) 2.7 V to 5.5 V Operatin
9、g free-air temperature range (TA) -55C to +125C _ 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended
10、 operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The manufacturer and/or distributor maintain no respon
11、sibility or liability for product used beyond the stated limits. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09607 REV PAGE 4 2. APPLICABLE DOCUMENTS JEDEC PUB
12、 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly mar
13、ked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicabl
14、e) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified
15、 herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. 3.5.3 Logic diagram. The logic diagram shall be as shown in figure 3. Provided by IHSNot for ResaleNo reproduction
16、or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09607 REV PAGE 5 TABLE I. Electrical performance characteristics. 1/ Limits Test Symbol Conditions V+ = 2.7 V to 5.5 V Temperature, TADevice type Min Max Unit T
17、emperature input section Range -55 +125 C Accuracy (temperature error) -25C to +85C 1.5 C -55C to +125C 2.0 -55C to +150C 1.5 typical Temperature input versus supply voltage 0.1 typical C/V Resolution 2/ Selectable -55C to +125C 01 0.0625 typical C Digital input/output section High input logic level
18、 VIH0.7(V+) V Low input logic level VIL0.3(V+) V Input current, SO/I, SCK, CS IIN0 V VIN V+ 1 A Output logic levels VOLSO/I ISINK= 3 mA 0.4 VOHSO/I ISOURCE= 2 mA (V+) - 0.4 VOLALERT ISINK= 4 mA 0.4 V Leakage current, ALERT 0 V VIN 6 V 1 A Input capacitance, SO/I, SCK, CS , ALERT CIN2.5 typical pF Re
19、solution 2/ Selectable 9 to 12 + sign typical bits 9 bit + sign 40 10 bit + sign 80 11 bit + sign 160 Conversion time 12 bit + sign -55C to +125C 01 320 ms See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY
20、CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09607 REV PAGE 6 TABLE I. Electrical performance characteristics Continued. 1/ Limits Test Symbol Conditions V+ = 2.7 V to 5.5 V Temperature, TADevice type Min Max Unit Power supply section Operating range V+ 2.7 5.5 V Quiescent
21、 current IQSerial bus inactive 75 A Shutdown current ISDSerial bus inactive -55C to +125C 01 1 A Temperature range section Specified range -55 +125 C Operating range -55 +150 C Storage range -60 +150 C Thermal resistance JACase X -55C to +125C 01 200 typical C/W 1/ Testing and other quality control
22、techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product perf
23、ormance is assured by characterization and/or design. 2/ Specified for 12-bit resolution. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09607 REV PAGE 7 Case X F
24、IGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09607 REV PAGE 8 Case X Dimensions Millimeters Symbol Min Max A - 1.45 A10.00 0.15 b 0.25 0.
25、50 c 0.08 0.22 D 2.75 3.05 E 1.45 1.75 E12.60 3.00 e 0.95 NOM L 0.30 0.55 L10.25 NOM NOTES: 1. All linear dimensions are in millimeters. 2. Body dimensions do not include mold flash or protrusion. Mold flash and protrusion shall not exceed 0.15 mm per side. 3. Leads 1, 2, 3 may be wider than leads 4
26、, 5, 6 for package orientation. 4. Falls within JEDEC MO-178 variation AB, except minimum lead width. FIGURE 1. Case outline Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT N
27、O. 16236 DWG NO. V62/09607 REV PAGE 9 Device type 01 Case outline X Terminal number Terminal symbol 1 ALERT 2 GND 3 V+ 4 SCK 5 CS 6 SO/I Terminal symbol I/O Description ALERT O Alert status pin GND - Ground V+ - Supply voltage SCK Serial clock CS Chip select SO/I Serial output/input data FIGURE 2. T
28、erminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09607 REV PAGE 10 FIGURE 3. Logic diagram. Provided by IHSNot for ResaleNo reproduction or net
29、working permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/09607 REV PAGE 11 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated
30、 in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall b
31、e in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salien
32、t characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be constr
33、ued as a guarantee of present or continued availability as a source of supply for the item. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Vendor part number Top-side marking V62/09607-01XE 01295 TMP122AMDBVTEP 122E 1/ The vendor item drawing establishes an admini
34、strative control number for identifying the item on the engineering documentation. CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group 8505 Forest Lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
