1、AMSC N/A FSC 5895 MIL-DTL-28837/2D 5 July 2012 SUPERSEDING MIL-DTL-28837/2C 30 October 2001 DETAIL SPECIFICATION SHEET MIXER STAGES, RADIO FREQUENCY, DOUBLE BALANCED, SOLDER LEADS This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements fo
2、r acquiring the product described herein shall consist of this specification and MIL-DTL-28837. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Pins not marked are grounded. 4. Pins without internal connections (dummy) are permitted provided the p
3、ins are labeled with a “D“. FIGURE 1. Outline drawing for mixers PIN M28837/2-01, M28837/2-02, M28837/2-03, M28837/02-04, M28837/2-07, M28837/2-08, M28837/2-09 and M28837/2-10. INCH-POUND Dimension Ltr Inches mm Min Max Min Max A .365 .405 9.27 10.29 B .313 - 7.95 - C .49 .53 12.4 13.5 D - .150 - 3.
4、81 E .012 DIA .022 DIA 0.30 DIA 0.59 DIA F .340 .360 8.64 9.14 G .240 .260 6.10 6.60 H .090 .110 2.29 2.79 J .075 .085 1.91 2.16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28837/2D 2 NOTES: 1. Dimensions are in inches. 2. Metric equivale
5、nts are given for general information only. 3. Pins not marked are grounded. 4. Pins without internal connections (dummy) are permitted provided the pins are labeled with a “D“. FIGURE 2. Outline drawing for mixers PIN M28837/2-05. Dimension Ltr Inches mm Min Max Min Max A .365 .405 9.27 10.29 B .31
6、3 - 7.95 - C .49 .53 12.4 13.5 D - .150 - 3.81 E .012 DIA .022 DIA 0.30 DIA 0.59 DIA F .340 .360 8.64 9.14 G .240 .260 6.10 6.60 H .090 .110 2.29 2.79 J .075 .085 1.91 2.16 K .075 NOM 1.91 NOM Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-2
7、8837/2D 3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Pins not marked are grounded. 4. Pins without internal connections (dummy) are permitted provided the pins are labeled with a “D“. FIGURE 3. Outline drawing for mixers PIN M28837/2-06. Dime
8、nsion Ltr Inches mm Min Max Min Max A .868 .872 22.05 22.15 B .098 .102 2.49 2.59 C .568 .572 14.43 14.53 D .253 .257 6.43 6.53 E .998 1.002 25.35 25.45 F .298 .302 7.57 7.67 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28837/2D 4 NOTES: 1
9、. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Case is to be grounded. FIGURE 4. Outline drawing for mixers PIN M28837/2-14 through M28837/2-16. Dimension Ltr Inches mm Min Max Min Max A .790 .810 20.07 20.57 B .175 .215 4.45 5.46 C .580 .600 14.73 15.24
10、 D .250 .270 6.35 6.86 E .017 DIA .019 DIA 0.43 DIA 0.48 DIA F .285 .305 7.24 7.75 G .057 RAD .067 RAD 1.45 RAD 1.70 RAD H .390 .410 9.91 10.41 K .120 .140 3.05 3.56 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28837/2D 5 NOTES: 1. Dimensi
11、ons are in inches. 2. Metric equivalents are given for general information only. 3. Case is to be grounded. FIGURE 5. Outline drawing for mixers PIN M28837/2-11. Dimension Ltr Inches mm Min Max Min Max A 1.090 1.110 27.69 28.19 B .175 .215 4.45 5.46 C .730 .750 18.54 19.05 D .180 .200 4.57 5.08 E .0
12、17 DIA .019 DIA 0.43 DIA 0.48 DIA F .369 .371 9.37 9.42 G .057 RAD .067 RAD 1.45 RAD 1.70 RAD H .540 .560 13.72 14.22 K .085 .205 2.16 5.21 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28837/2D 6 NOTES: 1. Dimensions are in inches. 2. Metr
13、ic equivalents are given for general information only. 3. Case is to be grounded. FIGURE 6. Outline drawing for mixers PIN M28837/2-12. Dimension Ltr Inches mm Min Max Min Max A .790 .810 20.07 20.57 B .175 .215 4.45 5.46 C .580 .600 14.73 15.24 D .180 .200 4.57 5.08 E .017 DIA .019 DIA 0.43 DIA 0.4
14、8 DIA F .285 .305 7.24 7.75 G .057 RAD .067 RAD 1.45 RAD 1.70 RAD H .395 .405 10.03 10.29 K .085 .105 2.16 2.68 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28837/2D 7 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for
15、 general information only. 3. Case is to be grounded. FIGURE 7. Outline drawing for mixers PIN M28837/2-13. Dimension Ltr Inches mm Min Max Min Max A .550 .570 13.97 14.48 B .175 .215 4.45 5.46 C .510 .530 12.95 13.46 D .180 .200 4.57 5.08 E .017 DIA .019 DIA 0.43 DIA 0.48 DIA F .271 .291 6.88 7.39
16、G .200 .220 5.08 5.59 H .270 .290 6.86 7.37 J .057 RAD .067 RAD 1.45 RAD 1.70 RAD K .085 .105 2.16 2.67 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28837/2D 8 REQUIREMENTS: Design and construction: Dimensions and configuration: See figure
17、s 1 through 7. Electrical characteristics: Operating frequency range: See table I. LO drive power: See table I. Conversion loss (max): See table I. Noise figure (SSB): See table I. Isolation (minimum): See table I. Maximum input power: See table I. Conversion compression: See table I. Desensitizatio
18、n (max): See table I. DC relative polarity: See table I. VSWR: See table I. Third order, two tone intermodulation: See table I. Impedance: 50 ohms. Physical and environmental characteristics: Weight: See table II. Temperature: See table II. Mechanical shock: See table II. Hermetic seal: See table II
19、. Terminal strength: See table II. Life: See table II. Part or Identifying Number (PIN) Space flight mixers shall be marked with “T”, M28837/2- 01 T. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AMSC N/A FSC 5895 TABLE I. Electrical characteristic
20、s. 1/ Dash no. Operating frequency range LO input drive power in dBm 2/ Maximum conversion loss (SSB) dB Noise figure (SSB) dB Isolation Minimum Frequency LO-RF LO-IF RF-IF dB dB dB 01N 01S MHz RF 5-1,000 LO 5-1,000 IF DC-1,000 minimum +10 TV +10 maximum +17 8.0 at: fLand fR5-1,000 MHz fIDC-1,000 MH
21、z Within 1 dB of conversion loss 40 40 30 5-100 MHz 30 25 15 100-1,000 MHz 02N 02S MHz RF 10-1,500 LO 10-1,500 IF DC-1,000 minimum +4 TV +7 maximum +13 7.0 at: fR20-600 MHz fL10-800 MHz fIDC-200 MHz 7.0 at: fR20-600 MHz fL10-800 MHz fI0.4-200 MHz 30 30 N/A 10-600 MHz 8.0 at: fR10-1,200 MHz fL10-1,40
22、0 MHz fIDC-200 MHz 8.0 at: fR10-1,200 MHz fL10-1,400 MHz fI0.4-200 MHz 25 20 N/A 600-1,200 MHz fR10-1,500 MHz fL10-15,000 MHz 8.5 at: fIDC-200 MHz 9.5 at: fIDC-1,000 MHz fR10-1,500 MHz fL10-15,000 MHz 8.5 at: fI0.4-200 MHz 9.5 at: fI0.4-1,000 MHz 25 18 N/A 1,200-1,500 MHz 03N 03S GHz RF 0.6-2.0 LO 0
23、.6-2.0 IF DC-1.0 minimum +4 TV +7 maximum +13 9.0 at: fRand fL0.6-2.0 GHz fIDC-1.0 GHz Within 1 dB of conversion loss 25 23 25 0.6-1.0 GHz 7.5 at: fRand fL1.0-2.0 GHz fIDC-1.0 GHz 20 12 15 1.0-2.0 GHz See footnotes at end of table. MIL-DTL-28837/2D9Provided by IHSNot for ResaleNo reproduction or net
24、working permitted without license from IHS-,-,-TABLE I. Electrical characteristics - Continued. 1/ Dash no. RF and LO 6/ maximum power input (rms) Conversion compression (maximum) Desensitization (maximum) Relative dc polarity 7/ VSWR (maximum) Third order, two tone intermodulation LO IF RF dBm Freq
25、uencies 01N 01S 50 mW N/A N/A Positive - - - - 02N 02S 140 mW 1.0 dB at PR0 dBm 1.0 dB at PR-2 dBm Negative - - - +10 03N 03S 300 mW 1.0 dB at PR0 dBm 1.0 dB at PR0 dBm Positive 2.5:1 2.5:1 2.5:1 36 8/ fL0: 35 MHz fR1: 25 MHz at -10 dBm fR2: 25 MHz at -10 dBm See footnotes at end of table. 10MIL-DTL
26、-28837/2DProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Physical and environmental characteristics - Continued. 1/ Dash no. Operating frequency range LO input drive power in dBm 2/ Maximum conversion loss (SSB) dB Noise figure (SSB) dB Isol
27、ation Minimum Frequency LO-RF LO-IF RF-IF dB dB dB 04N 04S MHz RF 0.5-500 LO 0.5-500 IF DC-500 minimum +7 TV +7 maximum +17 7.0 at: fLand fR1-300 MHz fIDC-300 MHz Within 1 dB of conversion loss 40 30 23 0.5-300 MHz 8.0 at: fLand fR0.5-500 MHz fIDC-500 MHz 35 20 20 0.5-500 MHz 05N 05S MHz RF 0.5-500
28、LO 0.5-500 IF1and IF2DC-500 minimum +7 TV +7 maximum +13 3/ 7.0 at: RF port to IF1.5-500 MHz 4/ Within 1 dB of conversion loss 35 30 25 0.5-10 MHz 7.0 at: LO port to IF1.5-500 MHz 5/ 30 25 20 10-200 MHz 25 20 15 200-500 MHz 06N 06S MHz RF 0.5-400 LO 0.5-600 IF DC-600 minimum +7 TV +7 maximum +17 6.5
29、 at: fLand fR1-100 MHz fIDC-100 MHz 6.5 at: fLand fR1-100 MHz fIDC-100 MHz 45 30 20 1-100 MHz 8.0 at: fLand fR0.5-400 MHz fIDC-1.0 MHz 8.0 at: fLand fR0.5-400 MHz fIDC-400 MHz 35 25 10 .5-400 MHz See footnotes at end of table. 11MIL-DTL-28837/2DProvided by IHSNot for ResaleNo reproduction or network
30、ing permitted without license from IHS-,-,-TABLE I. Electrical characteristics - Continued. 1/ Dash no. RF and LO 6/ maximum power input (rms) Conversion compression (maximum) Desensitization (maximum) Relative dc polarity 7/ VSWR (maximum) Third order, two tone intermodulation LO IF RF dBm Frequenc
31、ies 04N 04S 210 mW 1.0 dB at PR0-3 dBm N/A Positive - - - - 05N 05S 280 mW 1.0 dB at PR+1 dBm 1.0 dB at PR2 -3 dBm Negative - - - - 06N 06S 140 mW 8.0 dB at PL+17 dBm N/A Negative - - - - See footnotes at end of table. 12MIL-DTL-28837/2DProvided by IHSNot for ResaleNo reproduction or networking perm
32、itted without license from IHS-,-,-TABLE I. Physical and environmental characteristics - Continued. 1/ Dash no. Operating frequency range LO input drive power in dBm 2/ Maximum conversion loss (SSB) dB Noise figure (SSB) dB Isolation Minimum Frequency LO-RF LO-IF RF-IF dB dB dB 07N 07S GHz RF 0.5-1.
33、0 LO 0.5-1.0 IF DC-1.0 minimum +4 TV +7 maximum +13 7/ 7.5 at: fL and fR5-500 MHz fIDC-500 MHz Within 1 dB of conversion loss 35 30 25 5-50 MHz 8.0 at: fL and fR500-1,000 MHz fIDC-1,000 MHz 30 25 20 50-500 MHz 25 20 15 500-1,000 MHz 08N 08S GHz RF 0.75-2.0 LO 0.5-2.0 IF DC-1.2 minimum -3 TV 0 maximu
34、m +5 7.0 at: fL and fR500-1,000 MHz fIDC-1,000 MHz Within 1 dB of conversion loss 35 27 21 500-1,000 MHz 10.0 at: fL and fR1,000-2,000 MHz fIDC-1,200 MHz 27 24 17 1,000-2,000 MHz 09N 09S MHz RF 1-3,500 LO 1-3,500 IF 5-2,500 minimum +7 TV +10 maximum +24 7.0 at: fLand fR5-1,000 MHz fIDC-1,000 MHz Wit
35、hin 1 dB of conversion loss 30 30 30 5-1,000 MHz 9.5 at: fLand fR1-3,500 MHz fIDC-2,500 MHz 20 20 18 1-3,500 MHz See footnotes at end of table. 13MIL-DTL-28837/2DProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Electrical characteristics - Co
36、ntinued. 1/ Dash no. RF and LO 6/ maximum power input (rms) Conversion compression (maximum) Desensitization (maximum) Relative dc polarity 7/ VSWR (maximum) Third order, two tone intermodulation LO IF RF dBm Frequencies 07N 07S 300 mW 1.0 dB at PR0 dBm 1.0 dB at PR2 -2 dBm Negative 3.0:1 2.5:1 3.0:
37、1 +48 fL0: 20 MHz fR1 and fR2: 250 MHz at -10 dBm +41 8/ fL0: 20 MHz at +7 dBm fR1 and fR2: 750 MHz at -10 dBm 08N 08S 200 mW 1.0 dB at PR-8 dBm 1.0 dB at PR-10 dBm Negative 3.5:1 - 2.5:1 +7 8/ fL0: 50 MHz fR1 and fR2: 1,000 MHz at -10 dBm 09N 09S 300 mW 1.0 dB at PR+7 dBm 1.0 dB at PR +5 dBm Negati
38、ve 2.0:1 1.5:1 2.5:1 +55 8/ fL0: 60 MHz fR1 and fR2: 10 MHz at -10 dBm +56 fL0: 60 MHz fR1 and fR2: 3,000 MHz at -10 dBm See footnotes at end of table. MIL-DTL-28837/2D14Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Physical and environmen
39、tal characteristics - Continued. 1/ Dash no. Operating frequency range LO input drive power in dBm 2/ Maximum conversion loss (SSB) dB Noise figure (SSB) dB Isolation Minimum Frequency LO-RF LO-IF RF-IF dB dB dB 10N 10S GHz RF 0.8-2.4 LO 0.8-3.5 IF DC-1.5 minimum +4 TV +7 maximum +13 8.0 at: fR1.0-2
40、.0 GHz fL0.8-3.5 GHz fI0.01-1.5 GHz 8.0 at: fR1.0-2.0 GHz fL0.8-3.5 GHz fI0.01-1.5 GHz 25 18 20 0.8-2.0 GHz 8.5 at: fR0.8-2.4 GHz fL0.8-3.5 GHz fI0.01-1.5 GHz 8.5 at: fR0.8-2.4 GHz fL0.8-3.5 GHz fI0.01-1.5 GHz 20 20 20 2.0-3.5 GHz 11N 11S GHz RF 2.5-5.5 LO 2.5-7.0 IF DC-1.5 minimum +7 TV +9 maximum
41、+13 6.5 at: fL3-5.5 GHz fR3-5.0 GHz fI0.03-0.5 GHz 6.5 at: fL3-5.5 GHz fR3-5.0 GHz fI0.03-0.5 GHz 30 17 20 2.5-7 GHz 2.5-3.5 GHz 3.5-7.0 GHz 7.0 at: fL2.5-7.0 GHz fR2.5-5.5 GHz fI0.03-1.5 GHz 7.0 at: fL2.5-7.0 GHz fR2.5-5.5 GHz fI0.03-1.5 GHz 12N 12S GHz RF 4.5-9.5 LO 2.5-11.5 IF DC-2.0 minimum +7 T
42、V +10 maximum +13 7.0 at: fR5-9 GHz fL4-10 GHz fI0.03-1 GHz 7.0 at: fR5-9 GHz fL4-10 GHz fI0.03-1 GHz 25 2.5-9 GHz 20 9-11.5 GHz 15 4-11.5 GHz 8.0 at: fR4.5-9.5 GHz fL2.5-11 GHz fI0.03-2 GHz 8.0 at: fR4.5-9.5 GHz fL2.5-11 GHz fI0.03-2 GHz 10 2.5-4 GHz 15 4.5-8.0 GHz 18 8-9.5 GHz See footnotes at end
43、 of table. 15MIL-DTL-28837/2DProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Electrical characteristics - Continued. 1/ Dash no. RF and LO 6/ maximum power input (rms) Conversion compression (maximum) Desensitization (maximum) Relative dc po
44、larity 7/ VSWR (maximum) Third order, two tone intermodulation LO IF RF dBm Frequencies 10N 10S 200 mW 1.0 dB at PR0 dBm 1.0 dB at PR2-2 dBm Negative 2.0:1 2.5:1 3.0:1 +12 8/ fL0: 3.5 GHz fR1: 2.5 GHz at -10 dBm fR2: 2.51 GHz at -10 dBm 11N 11S 200 mW 1.0 dB at PR+3 dBm 1.0 dB at PR2-2 dBm Positive
45、2.5:1 2.5:1 3.3:1 11 8/ fL0: 5.0 GHz fR1: 4.0 GHz at -10 dBm fR2: 4.01 GHz at -10 dBm 12N 12S 200 mW 1.0 dB at PR+3 dBm 1.0 dB at PR2-2 dBm Positive 2.1:1 3.5:1 2.2:1 +13 8/ fL0: 8 GHz fR1: 7 GHz at -6 dBm fR2: 7.01 GHz at -6 dBm See footnotes at end of table. 16MIL-DTL-28837/2DProvided by IHSNot fo
46、r ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Physical and environmental characteristics - Continued. 1/ Dash no. Operating frequency range LO input drive power in dBm 2/ Maximum conversion loss (SSB) dB Noise figure (SSB) dB Isolation Minimum Frequency LO-RF
47、LO-IF RF-IF dB dB dB 13N 13S GHz RF 7-18 LO 5-18 IF DC-3 minimum +7 TV +10 maximum +13 8.0 at: fR8-16 GHz fL5-18 GHz fI0.03-3 GHz fL fR8.0 at: fR8-16 GHz fL5-18 GHz fI0.03-3 GHz 22 5-14 GHz 15 14-18 GHz 8.5 at: fR8-16 GHz fL5-16 GHz fI0.03-3 GHz fL fR8.5 at: fR8-16 GHz fL5-16 GHz fI0.03-3 GHz 12 5-8 GHz 22 8-18 GHz 9.0 at: fR16-18 GHz fL13-18 GHz fI0.03-3 GHz 9.0 at:
