1、AMSC N/A FSC 5935 INCH-POUND MIL-DTL-32385/3 14 July 2011 SUPERSEDING MS90335D 5 January 1996 DETAIL SPECIFICATION SHEET CONNECTOR, RECEPTACLE, CENTER CONTACT POSITIVE, ISOLATED GROUND TYPE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requi
2、rements for acquiring the product described herein shall consist of this specification sheet, MIL-DTL-32385, and QPL-32385. INTENDED USE: 1. The connectors covered by this specification sheet are intended for use on control and instrument panels for aircraft, ground, and shipboard applications. REQU
3、IREMENTS: 1. Material: Material shall be in accordance with MIL-DTL-32385. 2. Finish: Finish shall be in accordance with MIL-DTL-32385. 3. Design: Design shall be in accordance with MIL-DTL-32385. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D
4、TL-32385/3 2 NOTES: 1. The part or identifying number (PIN) consists of the letters MS, the specification number, the specification sheet number, and the dash number taken from table 1. MS 90335 - X X Type: A - Cup B - Pin Dash number (see table I) Specification number MS prefix (Retaining MS part n
5、umber) TABLE I. Dash number PIN cross-reference data. Dash number 1Type MS90335D PIN MIL-DTL-32385/3 PIN -5 A MS90335-5 MS90335-5A -5 B N/A 2MS90335-5B 1 See figures 1 and 2. 2 MS90335-5 had an alternative center connector option added that was not previously identified in MS90335D (see note 8). 2.
6、Interpret figure in accordance with ASME Y14.5. 3. When mated with MIL-DTL-32385/5, or /6 plug that has been inserted to a depth of 0.140 0.005 inch, the connector shall have a minimum withdrawal force of 3 pounds of force (lbf) and a maximum withdrawal force of 10 lbf. 4. The manufacturers identifi
7、cation mark shall be permanently stamped in the metal part of the connectors. 5. The current loading of the connectors is limited to the current-carrying capacity of the wire used in the associated interconnecting cabling. 6. In the event of a conflict between the text of this document and the refer
8、ences cited herein, the text of this document takes precedence. 7. Unless otherwise specified, issues of reference documents are those in effect at the time of solicitation. 8. Interchangeability relationship: MS90335-5 and MIL-DTL-32385/3-5A and -5B parts are universally, functionally and dimension
9、ally interchangeable. MS90335-5 had not identified an existing option for second center contact type with dash numbers. Users must determine whether the MS90335-5 employed a cup or a pin type center contact. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH
10、S-,-,-MIL-DTL-32385/3 3 NOTES: 1. All dimensions are in inches. 2. Tolerances: Dimensions 0.005 unless otherwise specified. 3. Female center contact fingers closed down uniformly to meet 4 ounce minimum withdrawal force with 0.079 diameter pin before and after 3 insertions of a 0.082 diameter pin. 4
11、. Angular dimension of 2.5 degrees. FIGURE 1. Connector, receptacle, center cup contact positive, isolated ground type, for -5A. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32385/3 4 NOTES: 1. All dimensions are in inches. 2. Tolerances:
12、Dimensions 0.005 unless otherwise specified. 3. Female center contact fingers closed down uniformly to meet 4 ounce minimum withdrawal force with 0.079 diameter pin before and after 3 insertions of a 0.082 diameter pin. 4. Angular dimension of 2.5 degrees. FIGURE 2. Connector, receptacle, center pin
13、 contact positive, isolated ground type, for -5B. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32385/3 5 Custodians: Preparing Activity: Army - AV Navy - AS Air Force - 85 DLA - GS DLA - GS2 (Project 5935-2011-033) Review Activities: Navy
14、- MC, SH NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
