1、 MIL-DTL-83528/8E 19 November 2013 SUPERSEDING MIL-DTL-83528/8D 15 November 2001 DETAIL SPECIFICATION SHEET GASKETING MATERIAL, CONDUCTIVE, SHIELDING GASKET, ELECTRONIC, ELASTOMER, EMI/RFI, HOLLOW P-STRIP This specification is approved for use by all Departments and Agencies of the Department of Def
2、ense. The requirements for acquiring the relay described herein shall consist of this specification sheet and the latest issue of MIL-DTL-83528. NOTE: Length shall be as specified on the purchase order. FIGURE 1. EMI/RFI gasket, elastomer, and hollow P-strip. AMSC N/A FSC 5999 INCH-POUNDProvided by
3、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83528/8E 2 REQUIREMENTS: Design and interface: See figure 1 and table I. Material: Type A, B, C, D, E, F, H, J, K, L, or M. Part or Identifying Number (PIN): See table I. Supersession information: See table
4、 II. TABLE I. Dimensions. PIN 1/ M83528/008X Nominal dimensions 2/, 3/ Cross section area (cm2) 4/ A B C D 001 .200 (5.08) .080 (2.03) .650 (1.65) .062 (1.57) .430 002 .250 (6.35) .125 (3.18) .250 (6.35) .062 (1.57) .359 003 .250 (6.35) .125 (3.18) .375 (9.53) .062 (1.57) .409 004 .250 (6.35) .150 (
5、3.96) .375 (9.53) .062 (1.57) .374 005 .312 (7.92) .187 (4.75) .563 (14.30) .062 (1.57) .585 006 .360 (9.14) .255 (6.48) .420 (10.67) .070 (1.79) .562 007 .200 (5.08) .080 (2.03) .275 (6.99) .062 (1.57) .294 008 .250 (6.35) .125 (3.18) .625 (15.88) .062 (1.57) .509 1/ “X” in the PIN shall be replace
6、d by the applicable material type. Complete PIN example: M38528/008A001. 2/ Dimensions are in inches; metric equivalents are given in parenthesis and are for general information only. 3/ Tolerance shall be as follows: Dimensions Tolerance Under Over .101 (2.57) .101 to .200 (2.57 to 5.08) .201 to .3
7、00 (5.10 to 7.62) .301 to .500 (7.62 to 12.70) .500 (12.70) .005 (0.13) .008 (0.20) .010 (0.25) .015 (0.38) .020 (0.51) 4/ For calculation of volume resistivity (for reference only). Table II. Supersession information. PIN 1/ M83528/008X Superseded DESC Drawing PIN 85107X 1/ 001 001002 002003 003004
8、 004 005 005006 006007 N/A 0081/ “X in the PIN indicates the applicable material type. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government ass
9、umes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. This documen
10、t references MIL-DTL-83528. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83528/8E 3 Custodians: Preparing activity: Army CR DLA CC Navy EC Air Force 85 (Project 5999-2013-016) DLA CC Review activities: Air Force 19, 99 NSA NS NOTE: The act
11、ivities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
