1、I INCH POUND I 18 June 1992 SUPERSEDING 5 April 1988 MIL-J-83388E MIL-J-83388D MILITARY SPECIFICATION JACKET, FLYERS, COLD WEATHER This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification contains the requirements for
2、 the CWU-45/P cold weather flyers jacket and hood, detachable. 1.2 Classification. The jackets shall be furnished in one of the following types or sizes as specified (see 6.2): Schedule of sizes Small 34 - 36 Medium 38 - 40 Large 42 - 44 Extra large 46 - 48 Extra extra large .50 - 52 1.2.1 The hoods
3、 shall be furnished in one of the following sizes as specified (see 6.2): Small, Medium, Large, Extra large, Extra extra large. . Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Personne
4、l Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8415 DISTRIBUTION STATE
5、MENT A. Approved for public release; distribution is unlimited. . . Licensed by Information Handling ServicesMIL-J-83388E 84 9999906 0575278 9 = MIL-J-83388E 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 specif docume Specifications, standards, and handbooks. The following ications, standa
6、rds, and handbooks form a part of this mnt to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2).
7、SPECIFICATIONS FEDERAL A-A-5 20 85 A-A-5 2 O 9 4 V-B-871 V-F-106 KK-L-2004 NN-P-71 DDD-L-20 PPP-B-636 PPP-T-45 MILITARY MIL-(2-3735 MIL-W-5664 MIL-C-6590 MIL-P-15011 MIL-F-21840 MIL-C-4 37 74 MIL-C-43824 MIL-T-44100 MIL-B-81813 MIL-C-81814 Cloth, Drill Cotton Thread, Cotton Button, Sewing Hole, and
8、Button, Staple (Plastic) Fastener, Slide, Interlocking. Leather, Cattlehide, Deerskin, and Horsehide, Chrome Tanned Pallet, Material Handling, Wood, Stringer Construction 2 Way and 4 Way (Partial) Label; for Clothing, Equipage, and Tentage, (General Use) Boxes, Shipping Fiberboard Tape, Gummed, Pape
9、r, Reinforced and Plain, for Sealing and Securing Cuffs, Knit, Wrist and Ankle, and Cloth, Knitted Webbing, Textile, Elastic, Cotton Cloth, Pile (Synthetic Mouton, Knitted) Pallet, Material Handling, Wood, Post Construction, 4 Way Entry Fastener Tapes, Hook and Loop, Synthetic Cloth, Plain or Pajama
10、 Check Weave, Aramid Cloth, Synthetic Fur, Knitted Thread, Pararamid, Spun Intermediate Modulus Batting, Aramid or Novoloid Fiber, Quilted . Cloth, Twill, Aramid, High Temperature Resistant 2 Licensed by Information Handling Services. MIL-J-83388E 4 9999906 0575279 O MIL-J-83388E MIL-C-83242 Cord, A
11、romatic Polyamide, Nonmel ting STANDARDS FEDERAL FED-STD-191 FED-STD-751 MILITARY Textile Test Methods Stitches, Seams, and Stitchings MIL-STD-105 MIL-STD-129 MIL-STD-147 MIL-STD-2073-1 MIL-STD-2073-2 Sampling Procedures and Tables for Inspection by Attributes Marking for Shipment and Storage Pallet
12、ized Unit Loads DOD Materials Procedures for Development and Applications of Packaging Requirements Packaging Requirement Codes (Unless otherwise indicated, copies of federal and military specifications, standards and handbooks are available from the Standardization Documents Order Desk, Bldg. 4D, 7
13、00 Robbins Avenue, Philadelphia, Pa. 19111-5094). 2.1 Non-Government Publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted shall be those listed in the issue of the DODISS cit
14、ed in the solicitation (see 6.2). NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classification (Applications for copies should be addressed to the American Trucking association, ATTN: Traffic Department, 1616 P Street, N.W., Washington, DC 20036-1404). UNIFORM CLASSI
15、FICATION COMMITTEE, AGENT Uniform Freight Classification (Applications for copies should be addressed to the Uniform Classification Committee, Room 1106, 222 South Riverside Plaza, Chicago, Illinois 60606-5808). THE COLOR ASSOCIATION OF THE UNITED STATES Department of Defense Standard Shades For Sew
16、ing Threads Department of Defense Standard Shades For Buttons 3 Licensed by Information Handling ServicesMIL-J-83388E 84 = 9999906 0575280 7 WIL-J-83388E O (Applications forcopies should be addressed to the Color Association of the United States, 409 W 44th St., New York, NY 10016-0927). AMERICAN SO
17、CIETY FOR TESTING AND MATERIALS ASTM D 3951 Standard Practice for Commercial Packaging (Applications for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187). (Non-Government standards and other publications are normally availab
18、le from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services). 2.2 Order of Drecedence. In the event of a conflict between the text of this document and the references cited herein, the text of this
19、document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified, (see 6.2), a sample shall be subjected to first article inspection, in accordance with 4.3. 3.2 M
20、aterials. e 3.2.1 Basic material (Jacket). The material for the outer shell, the hanger, and the fastener thong, shall conform to MIL-C-81814 and shall be USAF color shade No. 1565 (see 6.3). 3.2.1.1 Basic material (Hood). The material for the outer shell, the hanger, and the fastener thong, shall c
21、onform to MIL-C-81814 and shall be USAF color shade No. 1565 (see 6.3). 3.2.2 Quilted lininq. The material for the quilted lining shall conform to MIL-B-81813, except that the color shall be sage green conforming to USAF color shade No. 1565 (see 6.3). The cover cloth shall be as specified in MIL-C-
22、43774, except that the yarns per inch filling shall be 69 (minimum) and the shrinkage shall not exceed 3.0 percent in either the warp or filling directions. One side of the quilted lining may be natural provided that the natural color side of the quilted lining shall face the outer shell material in
23、 the finished jacket. 3.2.3 Collar interlininq. The material for the collar interlining and stand shall conform to type I, class 2 of A-A-52085. 4 Licensed by Information Handling ServicesMIL-J-83388E 84 = 9977906 0575283 9 I 1 I I I I I I l I i a MIL-J-83388E 3.2.4 Thread. Thethread for all stitche
24、s, seams and stitchings shall conform to size T-35 of MIL-T-44100, unless otherwise specified herein. attaching and top stitching the knitted cloth. The cotton thread shall conform to type I, ticket No. 30, 3 ply of A-A-52094. The thread shall match the color of the basic material (see 3.2.1). 3.2.5
25、 Elastic webbinq. The elastic webbing for the biasback retention shall be type I or II, class 1, 1 inch wide, minimum of 0.035 inch thick, color optional, of MIL-W-5664. The cut length shall be as follows: As an option, cotton thread may be used for Cut Lenqth L/ Small Medium Large Extra Large Extra
26、 Extra Large 18-3/4 19-1/2 20-7/8 21-3/4 23 - i/ The measurement of the cut length is in inches 3.2.6 Slide fasteners. The slide fasteners shall conform to requirements of V-F-106 and of Table I of this specification. The chain and any other metal components except the automatic slide fastener shall
27、 be brass with a black chemical finish. The slide fastener tapes shall be a high temperature resistant, nonmelting polyamide and shall be dyed so that the color of the tapes shall approximately match the color of the basic fabric (see 3.2.1). The tapes shall not shrink more than 2 percent in the dir
28、ection of the warp. The slider on the slide fastener for the front opening shall have a long tab pull with a 1/2 inch-wide thong that is fabricated from the basic fabric. The sliders on the slide fasteners for the hood separation and for the utility and pencil pocket of the jacket shall have short t
29、ab pulls. The size of the hole of the pull tab used on the pencil pocket shall not exceed 3/16 inch. As an alternate, a pull tab without any hole may be used. 5 Licensed by Information Handling ServicesMIL-J-33E 84 9999906 0575282 O m MIL-J-83388E Size of Jacket TABLE I. Slide fasteners. Width (Inch
30、es) in Direction of Course of Material L/ Application Slide Fastener Size small jacket Front opening Hood separation Utility and pencil pocket Size medium jacket Front opening Hood separation Utility and pencil pocket Size large jacket Front opening Hood separation Utility and pencil pocket Size ext
31、ra large jacket Front opening Hood separation Utility and pencil pocket Size extra extra large jacket Front opening Hood separation Utility and pencil pocket Specification V-F-106 Stvle IV I I IV I I IV I I IV I I IV I I 8 3 3 8 3 3 8 3 3 8 3 3 8 3 3 Size MH M M MH M M MH M M MH M M MH M M Length (
32、Inches ) 21-1/2 16-1/2 4-3/4 22 17 4-3/4 22-1/2 17-1/2 4-3/4 23 18 4-3/4 23-1/2 18-1/2 4-3/4 3.2.7 Wristlets and waistband. The wristlets shall conform to type IV, class 2, size 2 of MIL-C-3735. The material for the waistband shall be the width specified in Table II and conform to type IV, class 3 o
33、f MIL-C-3735. The wristlets and the material for the waistband shall be USAF color shade No. 1525 (see 6.3). Sma 11 Medium Large Extra large Extra extra large 24 25 26 27 28 - i/ A tolerance of plus or minus 1/2 inch will be permitted. 6 Licensed by Information Handling ServicesMIL-J-8338E 4 9999906
34、 0575283 2 = MIL-J-83388E 3.2.8 Hood lininq. The lining for the hood shall be sage green and conform to type II of MIL-C-6590. 3.2.9 Drawstrinas. The drawstring cord for the hood of the jacket shall conform to type III of MIL-C-83242 and be dyed to match the color of the basic fabric (see 3.2.1). Ea
35、ch drawstring shall be 23 inches (2 1 inch) long. The ends of the drawstrings shall be tipped or impregnated with cellulose acetate or cellulose acetate butyrate. The length of the tipping or impregnate shall be 5/8 inch (2 1/8 inch). 3.2.10 Drawstrinq reinforcements. The leather for the drawstring
36、reinforcements of the jacket shall conform to type I, class 2; 1-1/2 to 3-1/4 ounces of KK-L-2004, color black. 3.2.11 Buttons. The buttons for attaching the hood to the jacket shall conform to type II, class D, styles 20 and 21, size 30 line of V-B-871 and shall be Shade Green AD, Cable 62012, in a
37、ccordance with the DOD Standard Shades for Buttons. 3.2.12 Hood trimminq. The trimming for the hood of the jacket shall conform to MIL-C-43824. The fur strips shall be 2 inches wide, and the length required shall be as specified in Table IV. 3.2.13 Fastener tape. The fastener tape shall be 1 inch wi
38、de, except the loop and hook fastener tape for the nameplate shall be 2 inches wide. The fastener tapes shall conform to Type II, class 1 of MIL-F-21840. The color of the fastener tape shall approximate the color of the basic fabric. 3.2.14 Cord beadinq. The material used for the cord beading in the
39、 edges of the slide fastener covers shall conform to type I of MIL-C-83242. 3.2.15 Fusible interlininq. The fusible interlining strips used on the back for stabilizing during the sewing operation shall be style No. SF 134 (manufactured by the Pellon Corporation, 1120 Avenue of the Americans, New Yor
40、k, NY 10036) or an equal. 3.3 Desiqn. The design of the jacket is as follows: The jacket shall be single breasted; shall have a bias cut back; and shall have a straight center front opening with a slide fastener closure. The jacket shall have a utility and pencil pocket on the left sleeve and two fr
41、ont (patch) pockets that have envelope storm flaps. Closure of the utility and pencil pocket shall be effected by slide fasteners. Closure of the flaps of the front pockets shall be effected with hook and loop fasteners tape. The jacket shall have an outer shell, a quilted lining, wristlets, and a w
42、aistband that are made of high temperature resistant, aromatic polyamide material. When specified, the jacket shall have a detachable hood (See 6.2). The design of the hood is as follows: The hood shall be detachable from the jacket. The hood shall have a synthetic fur ruff, a simulated furlike knit
43、ted 7 Licensed by Information Handling ServicesMIL-J-83388E 84 9999906 0575284 4 MIL-J-83388E mouton lining, and an, outershell of a high temperature resistant, aromatic polyamide material. accomplished by a slide fastener, and the hood shall have a drawstring adjustment. 3.4 Manufacturina operation
44、s reuuirements. The jacket and/or hood shall be manufactured in accordance with operation requirements specified in Table IV. The contractor is not required to follow the exact sequence of operations provided the finished jacket and/or hood is identical to that produced by following the sequence as
45、listed in Table IV. Minor modifications are permitted where necessary when using automatic equipment. These modifications shall not alter the dimensional, serviceability or appearance requirements cited in the specification. The operations numbered 28 to 38 are for the manufacturing of the hood only
46、. 3.4.1 Stitches, seams, and stitchinas. Stitches, seams and stitchings used in the construction of the jacket and/or hood shall conform to FED-STD-751. Whenever two or more methods, seams, or stitches are specified for the same operation, any one of them may be used. All seams shall start and finis
47、h evenly. Seam allowances shall be maintained so that raw edges run-Offs, twists, pleats, puckers, or open seams shall not result. Thread tensions shall be maintained so that there shall be no tight or loose tension. The looper thread (under thread) of stitch type 401 shall be on the inside of the j
48、ackets and hood. 3.4.1.2 Thread breaks and ends of seams. Thread breaks (all stitch types) shall be secured by stitching back of each end not less than 1/2 inch. Skipped stitches or thread breaks of stitch type 401 may be repaired using stitch type 301, if not caught in other seams or stitchings, sh
49、all be backtacked not less than 1/4 inch. The ends of a continuous line of stitching (except on labels) shall be overlapped not less than 1/2 inch. The ends of stitching on labels shall be overlapped not less than three stitches. The hood separation shall be 3.4.1.3 Sewinq tolerances. A tolerance of 2 1/16 inch shall be permitted for 1/4 inch gage and 5/16 inch gage stitching. tolerance of plus O (zero) or minus 1/8 inch shall be permitted for 3/8 inch gage stitching. A tolerance of plus O (zero) or minus 1/16 inch shall be permitted for raise seam 1/4 inch gage. A toler
