1、 MS27237F INCH-POUND14 May 2007 SUPERSEDING MS27237E 6 April 2001 DETAIL SPECIFICATION SHEET SHOULDER, SWIVEL FLANGE, ADAPTER, HOSE TO TUBE, HYDRAULIC FUEL AND OIL LINES, 1/2 THROUGH 3 IN. TUBING SIZES This specification is approved for use by all Departments and Agencies of the Department of Defens
2、e. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-5070. Inches mm .010 .015 .030 .031 .046 0.25 0.38 0.76 0.79 1.02 FIGURE 1. Shoulder dimensions and configuration. AMSC N/A FSC 4730Provided by IHSNot for ResaleNo reproduction or net
3、working permitted without license from IHS-,-,-MS27237F 2 Dash number A .015 (0.38 inches (mm) B inches (mm) C inches (mm) D Dia +.000 -.005 (0.13) inches(mm) E Dia .005 (0.13) inches(mm) F Diainches(mm)G Diainches(mm) H Diainches(mm) J inches(mm) K Rad .015 (0.38) inches (mm) L M inches (mm) -8 .87
4、5 (22.23).365 (9.27) .420 (10.67).504 (12.80).501 (12.73).625 (15.88).610 (15.49)-10 .271 (6.88) 1.000 (25.40).490 (12.45).545 (13.84).629 (15.98).626 (15.90).750 (19.05).735 (18.67).118 (3.00).113 (2.87).047 (1.19) .030 x 45 (0.76 x 45)break -12 1.250 (31.75).615 (15.62).670 .754 (19.15).751 (19.08
5、).938 (23.83).923 (23.44)- -16 1.500 (38.10).865 (21.97).920 1.004 (25.50)1.001 (25.43)1.188 (30.18)1.173 (29.79)- -20 .156 (3.96) .153 (3.89) .156 (3.96) .151 (3.84) 1.844 (46.84)1.115 (28.32)1.1701.254 (31.85)1.251 (31.78)1.500 (38.10)1.485 (37.72)45 - -24 2.125 (53.98)1.329 (33.76)1.4201.504 (38.
6、20)1.501 (38.13)1.750 (44.45)1.735 (44.07)- -32 2.750 (69.85)1.829 (46.46)1.9202.004 (50.90)2.001 (50.83)2.375 (60.33)2.360 (59.94)- -40 3.281 (83.34)2.180 (55.37)2.2952.379 (60.43)2.376 (60.35)2.875 (73.03)2.860 (72.64)- -48 .312 (7.92) .188 (4.78) .185 (4.70) .188 (4.78) .183 (4.65) 3.781 (96.04)2
7、805 (71.25)2.9203.004 (76.30)3.001 (76.23)3.375 (85.73)3.360 (85.34).065 (1.65).060 (1.52).062 (1.57) 34 - FIGURE 1. Shoulder dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27237F 3 NOTES: 1. Dimensions a
8、re in inches. 2. Metric equivalents are for information only, 3. Unless otherwise specified, tolerances are as follows: angles .5; decimals .005 inch (0.13 mm). 4. Break or radius all corners .010/.005 inch (max./min.) (0.25/0.13 mm (max./min.). 5. All diameters shall be concentric within .010 inch
9、0.25 mm) total indicator reading. 6. Unless otherwise specified, maximum surface roughness shall be 125 in Rain accordance with ASME B46.1. 7. Break all sharp edges and remove all burrs and slivers. FIGURE 1. Shoulder dimensions and configuration - Continued. REQUIREMENTS: Dimensions and configurat
10、ions: The design, construction, and physical dimensions shall be in accordance with MIL-DTL-5070 and figure 1 in case of conflict between this drawing and MIL-DTL-5070, this drawing shall govern. Intended use. This part is a component of MS27227 and MS27229. This item shall not be procured for stock
11、ing purposes. Material: Aluminum shall be in accordance with MIL-DTL-5070. Finish: Finish shall be in accordance with MIL-DTL-5070. Color identification: Color identification shall be in accordance with MIL-DTL-5070. Part or Identifying Number (PIN) example: MS 27237 -16 AAMaterial/finish code, see
12、table I Dash number on figure 1 Specification number MS prefix TABLE I. Code for material and finish. Code Dash size Material/finish AA -8 through -48 Aluminum anodic coating Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previou
13、s issue, due to the extent of the changes. Referenced documents. In addition to MIL-DTL-5070, this document references the following: MS27227 MS27229 ASME B46.1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27237F 4 CONCLUDING MATERIAL Custodians
14、 Preparing activity: Army - AT DLA - CC Navy - AS Air Force - 99 (Project 4730-2005-055) DLA - CC Review activities: Army - AV Navy - MC, SA Air Force - 11, 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
