1、MS27282B 7 January 2009 SUPERSEDING MS27282A 17 June 2003 DETAIL SPECIFICATION SHEET INSERT, ELECTRICAL CONNECTOR - RAMP POWER, 416/240 VOLTS, FEMALE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product descri
2、bed herein shall consist of this specification sheet and MIL-DTL-38159. Inches mm Inches mm Inches mm .005 .127 .365 9.271 1.302 33.071 .010 .254 .380 9.652 1.658 42.113 .015 .381 .406 10.319 2.606 66.192 .020 .508 .438 11.125 2.610 66.294 .031 .787 .562 14.287 3.000 76.200 .032 .813 .586 14.884 3.0
3、50 77.470 .046 1.168 .588 14.935 3.125 79.375 .062 1.587 .654 16.612 3.156 80.162 .070 1.778 .677 17.196 3.375 85.725 .125 3.175 .829 21.057 7.032 178.61 .250 6.350 1.000 25.400 8.218 208.74 .260 6.604 1.175 29.845 INCH-POUND NOTES: 1. The procurement specification for this part is MIL-DTL-38159. 2.
4、 Material: See procurement specification. 3. Remove all sharp edges. 4. Unless otherwise specified, tolerances are .010 inch. 5. For design feature purposes, this standard takes precedence over procurement documents referenced herein. 6. Reference documents shall be of the issue in effect on the dat
5、e of the Invitation for Bid. 7. Part or Identifying Number (PIN): MS27282-1. 8. Electrical contact: See figure 2. 9. Dimensions are in inches. Metric equivalents are given for information only. FIGURE 1. Configuration and dimensions for MS27282-1. AMSC N/A FSC 5935 Provided by IHSNot for ResaleNo re
6、production or networking permitted without license from IHS-,-,-MS27282B 2 FIGURE 1. Configuration and dimensions for MS27282-1 - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27282B 3 Inches mm Inches mm .002 .004 .005 .015 .030 .203
7、219 .051 .102 .127 .381 .762 5.159 5.568 .281 .312 .437 .500 1.062 6.858 7.137 7.937 11.112 12.700 26.987 174.19 NOTES: 1. The procurement specification for this part is MIL-DTL-38159. 2. Material: Brass, in accordance with ASTM-B36/B36M, ASTM-B121/B121M or ASTM-B124/B124M. See procurement specific
8、ation. 3. Finish: See procurement specification. 4. Unless otherwise specified, machined surfaces 125 or better in accordance with ASME-B46.1. 5. Remove all burrs and break all edges. 6. All dimensions shown are for finished part after plating. 7. Dimensions in inches. Unless otherwise specified, to
9、lerance is 0.005 inch. 8. All diameters must be concentric to each other within 0.004 TIR. 9. Contact, electrical plug connector, ramp power. 416/240 volts, small, female. For use with MS27282-1. FIGURE 2. Configuration and dimensions (contact). Provided by IHSNot for ResaleNo reproduction or networ
10、king permitted without license from IHS-,-,-MS27282B 4 Dimensions and configuration. See figure 1 and figure 2. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents.
11、 In addition to MIL-DTL-38159, this document references the following: ASME-B46.1 ASTM-B36/B36M ASTM-B121/B121M ASTM-B124/B124M CONCLUDING MATERIAL Custodians: Preparing activity: Air Force - 85 DLA - CC DLA - CC (Project 5935-2008-137) Review activity: Air Force - 99 NOTE: The activities listed abo
12、ve were interested in this document as of date of this document. Since organization and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
