1、AMSC N/A FSC 5340 MS35257C 10 November 2009 SUPERSEDING MS35257B 4 September 1992 DETAIL SPECIFICATION SHEET BRACE, CORNER, BOX, LARGE, 2 QUARTER-ELLIPSE FLANGES, 2 MOUNTING HOLES This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requireme
2、nts for acquiring the product described herein shall consist of this specification sheet. R 2.000R 1.750R 1.750R 2.000.059 .005C - COUNTERSINKB 2 - HOLESR .0944545AFIGURE 1. Brace. INCH-POUNDInactive for new design after 31 July 1997.Provided by IHSNot for ResaleNo reproduction or networking permitt
3、ed without license from IHS-,-,-MS35257C 2TABLE I. Part Numbers and Dimensions. PART NUMBER DIMENSIONS MATERIAL A LENGTH B C COUNTERSINK MS35257-1 1.375 .204 82 TO .375 +.016 MS35257-2 1.375 .204 NONE MS35257-3 1.375 .180 82 TO .328 +.016 MS35257-4 1.375 .180 NONE MS35257-5 1.250 .204 82 TO .375 +.0
4、16 MS35257-6 1.250 .204 NONE BRASS MS35257-7 1.250 .180 82 TO .328 +.016 MS35257-8 1.250 .180 NONE MS35257-9 1.125 .204 82 TO .375 +.016 MS35257-10 1.125 .204 NONE MS35257-11 1.125 .180 82 TO .328 +.016 MS35257-12 1.125 .180 NONE MS35257-13 1.375 .204 82 TO .375 +.016 MS35257-14 1.375 .204 NONE MS35
5、257-15 1.375 .180 82 TO .328 +.016 MS35257-16 1.375 .180 NONE MS35257-17 1.250 .204 82 TO .375 +.016 MS35257-18 1.250 .204 NONE STEEL MS35257-19 1.250 .180 82 TO .328 +.016 MS35257-20 1.250 .180 NONE MS35257-21 1.125 .204 82 TO .375 +.016 MS35257-22 1.125 .204 NONE MS35257-23 1.125 .180 82 TO .328 +
6、016 MS35257-24 1.125 .180 NONE Requirements: 1. Material: Brass, in accordance with ASTM B121/B121M, H02 (half-hard). Steel, in accordance with QQ-S-698, cold rolled, commercial quality, No. 2 temper, No. 1 finish. 2. Finish: Brass, plain. Steel, zinc plated in accordance with ASTM B633, Type IV, S
7、C3. 3. Tolerance: Tolerances on decimals .016, on angles 1, unless otherwise specified. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35257C 34. Part number: The part number consists of the basic specification sheet number plus the dash number. E
8、xample: MS35257 - 1 Dash number Basic specification sheet number Notes: 1. All dimensions are in inches, unless otherwise specified. 2. In the event of a conflict between the text of this standard and the references cited herein, the text of this standard shall take precedence. 3. Changes from previ
9、ous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Preparing Activity: Army -CR DLA -IS Navy - YD Air Force 99 (Project 5340-2009-026) NOTE: The activities listed above were interested in th
10、is document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
