1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update drawing to current requirements. Editorial changes throughout. - gap 09-03-26 Robert M. Heber CURRENT CAGE CODE IS 67268. The original first sheet of this drawing has been replaced. REV SHET REV SHET REV STATUS REV A A A A A A A A A A OF S
2、HEETS SHEET 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY David W. Queenan CHECKED BY D. A. DiCenzo DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil APPROVED BY N. A. Hauck STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF T
3、HE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 86-10-03 MICROCIRCUIT, DIGITAL, ADVANCED SCHOTTKY TTL, MAGNITUDE COMPARATOR, MONOLITHIC SILICON AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 14933 5962-86069 SHEET 1 OF 10 DSCC FORM 2233 APR 97 5962-E053-09 Provided by IHSNot for ResaleNo reproduction or
4、networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86069 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN
5、class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-86069 01 E X Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). The devi
6、ce type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54F85 4-bit magnitude comparator 1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or C
7、DIP2-T16 16 Dual-in-line package F GDFP2-F16 or CDFP3-F16 16 Flat package 2 CQCC1-N20 20 Square chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage range . -0.5 V dc to +7.0 V dc Input voltage range -0.5 V dc at -
8、18 mA to +7.0 V dc Storage temperature range . -65C to +150C Maximum power dissipation, (PD) per device 1/ . 297 m W Lead temperature (soldering, 10 seconds) . +300C Thermal resistance, junction-to-case (JC) See MIL-STD-1835 Junction temperature (TJ) +175C 1.4 Recommended operating conditions. Suppl
9、y voltage (VCC) 4.5 V dc minimum to 5.5 V dc maximum Minimum high-level input voltage (VIH) 2.0 V dc Maximum low-level input voltage (VIL) . 0.8 V dc Case operating temperature range (TC) -55C to +125C _ 1/ Must withstand the added PDdue to short circuit test (e.g., IOS) Provided by IHSNot for Resal
10、eNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86069 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks
11、. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manu
12、facturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard
13、 Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of th
14、is drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in acco
15、rdance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-
16、38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications s
17、hall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The
18、design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The
19、 truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the ful
20、l case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license f
21、rom IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86069 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein.
22、In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be
23、marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of complia
24、nce shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of
25、MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall
26、 be required for any change that affects this drawing. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
27、reviewer. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspect
28、ion. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon re
29、quest. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except int
30、erim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86069 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3
31、990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits Test Symbol Conditions -55C TC +125C unless otherwise specified Group A subgroups Min Max Unit High level output voltage VOHVCC= 4.5 V, IOH = -1 mA, VIN= 0.8 V or 2.0 V 1, 2, 3 2.5 V Low level
32、output voltage VOLVCC= 4.5 V, IOL = 20 mA, VIN= 0.8 V or 2.0 V 1, 2, 3 0.5 V Input clamp voltage VICVCC= 4.5 V, IIN=-18 mA, TC= +25C 1 -1.2 V IIH1 VCC=5.5 V, VIN= 7.0 V 1, 2, 3 100 High level input current IIH2 VCC=5.5 V, VIN= 2.7 V 1, 2, 3 20 A Low level input current IILVCC=5.5 V, VIN= 0.5 V 1, 2,
33、 3 -20 A Short circuit output current IOSVCC=5.5 V, VOUT= GND 1/ 1, 2, 3 -60 -150 mA ICCH 1, 2, 3 50 Supply current ICCL VCC=5.5 V 1, 2, 3 54 mA Functional test See 4.3.1c 7 9 16 tPLH110, 11 21 9 16 Propagation delay time, A or B to A B tPHL110, 11 21 ns 9 16 tPLH210, 11 21 9 14 Propagation delay ti
34、me A or B to A = B tPHL210, 11 17 ns 9 9 tPLH310, 11 12 9 8 Propagation delay time, 1A B tPHL3VCC= 5.0 V, RL= 500 5 %, CL= 50 pF 10 % 10, 11 10 ns See footnotes on next page. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWI
35、NG SIZE A 5962-86069 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions -55C TC +125C unless otherwise specified Group A subgroups Min Max Unit 9 8 tPLH410,
36、 11 14 9 10 Propagation delay time, 1A = B to A = B tPHL410, 11 12 ns 9 9 tPLH510, 11 14 9 9 Propagation delay time, 1A B or 1A = B to A B|A B A B3X X X X X X H L L A3B2X X X X X H L L A3= B3A2B1X X X X H L L A3= B3A2= B2A1B0X X X H L L A3= B3A2= B2A1= B1A0 B0X X X L H L A3= B3A2= B2A1= B1A0= B0H L
37、L H L L A3= B3A2= B2A1= B1A0= B0L H L L H L A3= B3A2= B2A1= B1A0= B0L L H L L H A3= B3A2= B2A1= B1A0= B0X X H L L H A3= B3A2= B2A1= B1A0= B0H H L L L L A3= B3A2= B2A1= B1A0= B0L L L H H L H = HIGH voltage level L = LOW voltage level X = Dont care FIGURE 2. Truth table. Provided by IHSNot for ResaleN
38、o reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86069 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 9 DSCC FORM 2234 APR 97 FIGURE 3. Logic diagram. Provided by IHSNot for ResaleNo reproduction or network
39、ing permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86069 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 10 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-
40、STD-883, method 5005, table I) Interim electrical parameters (method 5004) - - - Final electrical test parameters (method 5004) 1*, 2, 3, 9 Group A test requirements (method 5005) 1, 2, 3, 7, 9, 10, 11* Groups C and D end-point electrical parameters (method 5005) 1, 2, 3 * PDA applies to subgroup 1.
41、 * Subgroup 10 and 11, if not tested, shall be guaranteed to the specified limits in table I. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intende
42、d for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared specification or drawing. 6.3 Configuration control of
43、 SMDs. All proposed changes to existing SMDs will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columb
44、us (DSCC) when a system application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962) should contact DSCC-
45、VA, telephone (614) 692-0544. 6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43218-3990, or telephone (614) 692-0547. 6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MIL-HDBK-103 have agreed to this dr
46、awing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DSCC-VA. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 09-03-26 Approved sources of supply for SMD 5962-86069
47、are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of
48、compliance has been submitted to and accepted by DSCC-VA. This information bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DSCC maintains an online database of all current sources of supply at http:/www.dscc.dla.mil/Programs/Smcr/. Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-8606901EA 3/ 54F85/BEA 5962-8606901FA 3/ 54F85/BFA 5962-86069012A 3/ 54F85/B2C 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the m
