1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device types 02 through 06. Add vendor CAGE 64155. Change CAGE code to 67268. 88-06-28 M. A. FRYE B Changes in accordance with N.O.R. 5962-R104-94. 94-02-24 M. A. FRYE C Add case outline Y. Make changes to 1.2.2, 1.3, 3.2.1, figure 1, and fig
2、ure 2. Redrawn. - ro 99-10-14 R. MONNIN D Drawing updated to reflect current requirements. - ro 02-07-24 R. MONNIN E Add device class V devices and add TABLE IIB. - ro 02-12-06 R. MONNIN F Drawing updated as part of 5 year review. -rrp 09-12-14 C. SAFFLE CURRENT CAGE CODE 67268 THE ORIGINAL FIRST PA
3、GE OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV F F F F F F F F F F F OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Charles E. Besore DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY D. A. DiCenzo COLUMBUS, OHIO 43218-3990 http:/www.dscc
4、.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Nelson Hauck MICROCIRCUIT, LINEAR, VOLTAGE REFERENCE, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 87-05-29 AMSC N/A REVISION LEVEL F SIZE A CAGE CODE 14933 5962-87594 SHEET 1 OF 11 DSCC F
5、ORM 2233 APR 97 5962-E418-07 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87594 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. T
6、his drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Ra
7、diation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following examples. For device classes M and Q: 5962 - 87594 01 X X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Case outline (see 1.2.4) Lead finish (see 1.2.5)
8、 / / Drawing number For device class V: 5962 - 87594 01 V Y X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA mar
9、ked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Devic
10、e type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 LM185-1.2 Voltage reference diode 02 LM185-2.5 Voltage reference diode 03 LM185BX1.2 Voltage reference diode 04 LM185BX2.5 Voltage reference diode 05 LM185BY1.2 Voltage reference di
11、ode 06 LM185BY2.5 Voltage reference diode 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as listed below. Since the device class designator has been added after the original issuance of this drawing, device classes M and Q design
12、ators will not be included in the PIN and will not be marked on the device. Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification
13、and qualification to MIL-PRF-38535 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87594 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outl
14、ine(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 2 TO-46 can Y GDFP1-G10 10 Flat pack with gullwing leads 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as spe
15、cified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 1.3 Absolute maximum ratings. 1/ Reverse current (IR) 30 mA Forward current (IF) . 10 mA Maximum power dissipation (PD) 113 mW Junction temperature (TJ) . +175C Lead temperature (soldering 10 seconds)
16、: Cases X and 2 . +300C Case Y . +260C Storage temperature range . -55C to +150C Thermal resistance, junction-to-case (JC): Case X . 80C/W Case Y . 23C/W Case 2 . See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Case X . 440C/W Case Y . 194C/W Case 2 . 100C/W 1.4 Recommended operating
17、conditions. Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issue
18、s of these documents are those cited in the solicitation or contract. 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or netwo
19、rking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87594 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specifi
20、cation for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (C
21、opies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the refere
22、nces cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in ac
23、cordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance wit
24、h MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and he
25、rein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless other
26、wise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in
27、 table IIA. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations,
28、 the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535,
29、appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. Provided by IHSNot for ResaleNo reproduction or net
30、working permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87594 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C unless otherwis
31、e specified Group A subgroups Device type Limits Unit Min Max Reverse breakdown voltage VREFIR= 10 A 1 01,03,05 1.223 1.247 V 10 A IR 20 A 2,3 1.205 1.26 IR= 20 A 1 02,04,06 2.462 2.538 V 20 A IR 30 A 2,3 2.425 2.575 IR= 1 mA 1 01,03,05 1.223 1.247 V 2,3 1.205 1.26 1 02,04,06 2.462 2.538 V 2,3 2.425
32、 2.575 IR= 20 mA 1 01,03,05 1.223 1.247 V 2,3 1.205 1.26 1 02,04,06 2.462 2.538 V 2,3 2.425 2.575 Reverse breakdown voltage change with current VREF/ 10 A IR 1 mA 1 01,03,05 -1 1 mV IR20 A IR 1 mA 2,3 -1.5 1.5 20 A IR 1 mA 1 02,04,06 -1 1 mV 30 A IR 1 mA 2,3 -1.5 1.5 1 mA IR 20 mA 1 All -10 10 mV 2,
33、3 -20 20 Forward bias voltage VFIF= 2 mA, TA= +25C 1 All -1 -0.4 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87594 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990
34、 REVISION LEVEL F SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Temperature coefficient 1/ TC1,2,3 03, 04 30 ppm/C 05, 06 50 1/ The average tem
35、perature coefficient is defined as the maximum deviation of reference voltage at all measured temperatures between the operating TMAXand TMINdivided by TMAX TMIN. The measured temperatures are -55C, -40C, 0C, +25C, +70C, +85C, and +125C. 3.6 Certificate of compliance. For device classes Q and V, a c
36、ertificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MI
37、L-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the r
38、equirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8
39、 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSC
40、Cs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices cover
41、ed by this drawing shall be in microcircuit group number 59 (see MIL-PRF-38535, appendix A). 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturers Quality Manage
42、ment (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. For device class M, sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. For device classes Q and V, screening shall be in accordance w
43、ith MIL-PRF-38535, and shall be conducted on all devices prior to qualification and technology conformance inspection. For device class M, screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. Provided by IHSN
44、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87594 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 7 DSCC FORM 2234 APR 97 Case X Symbol Inches Millimeters Min Max Min Max A .080 .105 2.03
45、2.67 b .016 .019 0.41 0.48 D .209 .219 5.31 5.56 D1 .178 .195 4.52 4.95 e - .100 - 2.54 e1 - .050 - 1.27 F - .030 - 0.76 k .036 .046 0.91 1.17 k1 .028 .048 0.71 1.22 L .500 - 12.70 - Q - .025 - 0.64 45 BSC 45 BSC NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general informa
46、tion only. 3. The U.S. government preferred system of measurement is the metric SI system. However, since this item was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. FIGURE 1. C
47、ase outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87594 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 8 DSCC FORM 2234 APR 97 Device types All Case outlines X Y 2
48、Terminal number Terminal symbol 1 VREFNC GND 2 GND NC NC 3 - NC NC 4 - NC NC 5 - V- NC 6 - NC NC 7 - NC NC 8 - NC NC 9 - NC NC 10 - V+ NC 11 - - VREF+12 - - NC 13 - - NC 14 - - NC 15 - - NC 16 - - NC 17 - - NC 18 - - NC 19 - - NC 20 - - NC NC = No connection FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro
