1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Added device types 02 and 03. Made changes to 1.3 and 1.4. Made technical changes to table I. Made changes to figures 1 and 2. Updated drawing to reflect MIL-H-38534 processing. 90-11-19 Monica Poelking B Added vendor CAGE 31757. Editorial change
2、s throughout. 91-09-17 Monica Poelking C Added vendor to 5962-87679032X and added footnote 2 to the 5962-87679012X vendor specified to incorrect military part number. Editorial changes throughout. 92-05-14 Gregory Lude D Changes in accordance with NOR 5962-R264-92. 92-07-27 Alan Barone E Add case ou
3、tlines T, U, X, and Y. Rewrite entire document. 93-08-02 K. A. Cottongim F Added device type 04 with cage 50434. Added case outline F to paragraph 1.2.3. Redrew entire document. 96-02-29 K. A. Cottongim G Changes in accordance with NOR 5962-R162-96. 96-06-24 Kendall A. Cottongim H Added class K devi
4、ces. Redrew entire document. -sld 98-04-09 K. A. Cottnogim J Paragraph 1.2.2, correct generic numbers for device types 01 and 05. Table I, Input to output insulation leakage current test (II/O), conditions column, change; relative humidity = 45 percent to relative humidity 65 percent. Editorial chan
5、ges throughout. 04-10-21 Raymond Monnin K Updated drawing paragraphs. -sld 12-01-17 Charles F. Saffle THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV K SHEET 15 REV STATUS REV K K K K K K K K K K K K K K OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY D
6、onald Osborne DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Steve L. Duncan THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Monica Poelking MICROCIRCUIT, HYBRID, LINEAR, DUAL AND QUAD CHANNEL, OPTICALLY CO
7、UPLED ISOLATOR AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 88-06-03 AMSC N/A REVISION LEVEL K SIZE A CAGE CODE 67268 5962-87679 SHEET 1 OF 15 DSCC FORM 2233 APR 97 5962-E057-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STAND
8、ARD MICROCIRCUIT DRAWING SIZE A 5962-87679 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL K SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead fini
9、shes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: For class H devices: 5962-87679 01 E X Drawing number Device type
10、 Case outline Lead finish (see 1.2.2) (see 1.2.4) (see 1.2.5) For class K devices: 5962 - 87679 05 K E X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Rad
11、iation hardness assurance (RHA) designator. Device classes H and K RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) shall identify the circuit
12、function as follows: Device type Generic number Circuit function 01 4N55, 66024-001A Dual channel, optocoupler with separate supply voltage and ground connections 02 HCPL-5531 Dual channel, optocoupler with common supply voltage and ground connections 03 HCPL-6531, 66125 Dual channel, optocoupler wi
13、th separate supply voltage connections 04 HCPL-6551 Quad channel, optocoupler with common supply voltage and ground connections 05 HCPL-257K, 66024-300A Dual channel, optocoupler with separate supply voltage and ground connections 06 HCPL-553K, 66124-300 Dual channel, optocoupler with common supply
14、voltage and ground connections 07 HCPL-653K Dual channel, optocoupler with separate supply voltage connections 08 HCPL-655K Quad channel, optocoupler with common supply voltage and ground connections 1.2.3 Device class designator. This device class designator shall be a single letter identifying the
15、 product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliab
16、ility class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. Provided by IHSNot for ResaleNo reproduction or networking permitted without lic
17、ense from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87679 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL K SHEET 3 DSCC FORM 2234 APR 97 G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a p
18、ossible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requ
19、irements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined
20、by the manufacturers internal, QML certified flow. This product may have a limited temperature range. 1.2.4 Case outline(s). The case outline(s) shall be as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E CDIP2-T16 16 Dual-in-lineP CDIP2-T8
21、8 Dual-in-line T See figure 1 16 Dual-in-line U See figure 1 16 Dual-in-line X See figure 1 8 Dual-in-line Y See figure 1 8 Dual-in-line 2 CQCC1-N20 20 Square leadless chip carrier F CDFP4-F16 16 Flat package1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maxi
22、mum ratings. 1/ Supply voltage range (each channel) -0.5 V dc to +20 V dc Output voltage range (each channel) . -0.5 V dc to +20 V dc Reverse input voltage (each channel) Device types 01and 05 5.0 V dc Device types 02, 03, 04, 06, 07, and 08. 3.0 V dc Output current (each channel) . 8 mA dc Input cu
23、rrent (each channel) 20 mA dc Peak input current (each channel 1 ms duration 500 pps) 40 mA dc Emitter base reverse voltage (each channel) 2/ 3.0 V dc Output power dissipation (each channel) 3/ . 50 mW Input power dissipation (each channel) 36 mW Storage temperature range -65C to +150C Lead temperat
24、ure (soldering, 10 seconds) 4/ +260C Junction temperature (TJ) +150C 1/ Unless otherwise specified, all voltages are referenced to ground. 2/ This parameter applies to the 01, 03, 05, and 07 device types only. 3/ Output power is collector power plus VCCsupply power for that channel. Derate linearly
25、1.4 mW/C above +100C. Derating applies to device types 01 and 05 only. 4/ 1.6 mm below seating plane. This applies to device types 01, 02, 05, and 06 only. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-8767
26、9 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL K SHEET 4 DSCC FORM 2234 APR 97 1.4 Recommended operating conditions. Supply voltage range (VCC) (each channel) . 2.0 V dc minimum to 18.0 V dc maximum Low level input current (each channel) 250 A dc maximum Case operating temperature
27、range (TC) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in th
28、e solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF D
29、EFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphi
30、a, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtai
31、ned. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturers Quality
32、Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in
33、the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) sh
34、all be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Switching test circuit and waveform(s). The switching test circuit and waveform(s) shall be as specified on figure 3. Provided by IHSNot for ResaleNo rep
35、roduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87679 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL K SHEET 5 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical
36、performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I.
37、 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-3853
38、4, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for tho
39、se which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manu
40、facturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance a
41、s required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. T
42、he modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test c
43、ircuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in acco
44、rdance with the intent specified in method 1015 of MIL-STD-883. (2) TAas specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are option
45、al at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87679 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL K SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electric
46、al performance characteristics. Test Symbol Conditions 1/ -55C TC+125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max INPUT Forward voltage (each channel) VFIF= 20 mA 1,2,3 01,05 1.80 V dc 02,03,04,06,07,08 1.90 Reverse breakdown voltage (each channel) BVRIR= 10 A 1,2,3
47、 01,05 5.0 V dc 02,03,04,06,07,08 3.0 COUPLED High level output current (each channel) IOHVO= VCC= 18 V 2/ 1,2,3 All 100 A dc Output leakage current (each channel) IOLEAKVO= VCC= 18 V 3/ 1,2,3 All 250 A dc Current transfer ratio (each channel) 4/ CTR VCC= 4.5 V, VO= 0.4 V, IF= 16 mA 1,2,3 All 9 % In
48、put to output insulation leakage current 5/ II/O TC= +25C, VI/O= 1500 V, Relative humidity 65 percent, t = 5 s 1 All 1.0 A dc Supply current (each channel) High level Low level ICCH2/ 1,2,3 01,03,05,07 10 A dc 7/ 1,2,3 04,08 40 02,06 20 ICCLIF1= IF2= 20 mA, IF3= IF4= 20 mA 6/ 1,2,3 01,03,05,07 200 A dc 04,08 800 02,06 400 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-
