1、DESC-DWG-b74 57 W 7777775 OOL3b b I LTR REVISIONS DESCRIPTtON PMIC NIA STANARDiZED Mi LITARY DRAWING THIS DRAWING IS AVAILABLE OR USE BY ALL DEPARNENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE DEFENSE ELECTRONICS SUPPLY CENTER DAWN, OHIO 45444 NONINVERTING, BUS INTERFACE REGISTERS, TTL COMPATIBLE.
2、MONOLITHIC SILICON I WE CAGECODE I 15 SEPTEMBER 1988 I A I 67268 15962-88674 I REVISION LEVEL I I I AMSC NIA I I SHEET 1 OF 14 DESC FORM 193 tr US. OOVIRiiANT PRIHTIti OfiKf: 1987 - 74 distrlbutlon Is unilmlled. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro
3、m IHS-,-,-I STANDARDIZED MILITARY DRAWING DEFENSE ELECTRONW SUPPLY CENTER MYTON, OHIO 45444 1, SCOPE 1.1 SCO e, This drawing describes device requirements for class B microcircuits in accordance iith l.pecifications and Standards specified in the solicitation, form a part of this drawing to the mxte
4、nt specified herei n . SPECIFICATION MILITARY MIL-M-38510 - Microcircuits, General Specification for. STANDARD MILITARY MI L-STD-883 - Test Methods and Procedures for Microelectronics. (Copies of the specification and standard required by manufacturers in connection with specific icquisition functio
5、ns should be obtained from the contracting activity or as directed by the ontracting activity. 1 leferences cited herein, the text of this drawing shall take precedence, 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the SIZE A 5962-88674 STANDARDIZED MILITA
6、RY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER I REVFSION LEVU I SHEET I I I 3 DAYTON, OHIO 45444 U.8.GOVERNMEMPRIMINOOFFNE: 1988-549-ffl IESC FORM 193A SEP 87 F, . f Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I 3. REQUIREMENTS 3.1 Item requiremen
7、ts. The individual item requirements shall be in accordance with 1.2,l of IIL4TD- ind as zified herein. “Provisions for the use of MIL-STD-883 in conjunction with compliant non-JAN devices“ 3.2 Design construction, and physical dimensions. The design, construction, and physical Hmensions shhl be as
8、specified 1 n MIL-M-3slO and herei n. 3.2.1 Case o.utlines, The case outlines shall be In accordance with 1.2.2 herein. 3.2.2 Terminal connections, The terminal connections shall be as Specified on figure 1. 3.2.3 Logic diagram. The logic diagram shall be as specified on figure 2. 3.2.4 Truth table,
9、 The truth table shall be as specified on figure 3, 3.2.5 Switching waveforms and test circuits, The switching waveforms and test cirufts shall be s specified an figure 4, 3.3 Electrical perfomance characteristics. Unless otherwise specified, the electrical lerformance characteristics are as specifl
10、ed in table I and apply over the full recomnended case iperating temperature range. 3,4 Markin , Marking shall be in accordance with MIL-STD-883 (see 3.1 herein). The part shall e rnarkd the part number listed in 1.2 herein. In addition, the manufacturers part number ia,y also be marked as listed in
11、 6.4 herein. n order to be IlStt?d as an approved source of supply in 6.4, The certificate of compliance dmltted to DESC-ECS prior to listing as an approved source of supply shall state that the nufacturers product meets the requirements of MIL-STD-883 (see 3.1 herein) and the requirements ierel n,
12、erein) snail be provrded with each lot of microcircuits delivered to this drawing, 3.5 Certificate of compliance. A certificate of compliance shall be required from a manufacturer 3.6 Certificate of conformance. A certificate of conformance as required in MIL-STD-883 (sec 3.1 37 Notification of chan
13、ge, Notification of change to DESC-ECS shall be required in accordance iith Mm (see 3.1 herein). 3.8 Veriflcation and review. DESC, DESCs a ent, and the acquirfn activity retain the option to eview The manufactureris tacrlity and appllcabge required documentatyon. Offshore documentation hall be made
14、 available onshore at the option of the reviewer. SIZE A 596246674. . STANDARDIZED MILITARY DRAWING EfWSE ELECTRONES SUPPLY Cm W“, OHD 45444 - ESC FORM 193A SEP a7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DESC-DWG-88b74 57 m 7777775 0033870 8
15、W I STANDARDIZED MILITARY DRAWING SIZE A 5962-88674 I DEFENSE ELECTRONICS SUPPLY CENTER DAMON, OHIO 45444 I REVI- I !#IEET E m I . “ ic U. S. OVWMENT PRIHTINQ MCE IWII-MO-ffl ESC FORM 193A SEP a7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I SIZE
16、 A STANDARDIZED TABLE I. Electrical performance characteristics - Continued. I Ievicel Group A I Limits I Unit I Conditions -55C plfCS WPPLY CENTER mN,$liK)M 6.4 Approved source of supply, An approved source of supply is listed herein. Additional ;oumes will be added as they become available. The ve
17、ndor listed herein has agreed to this drawing ind a certificat8 of compliance (see 3.5 herein) has been submitted to DESC-ECS. 1 I I I I Rilltary drawing I Vendor I Vendor I i part humber I CAGE I similar part I 1 number 1 numberA/ I I I I I I I 5962-8867401KX I 61772 I IDT54FCT825AEB I I I 1 I I 59
18、62-8867401LX I 61772 I IDT54FCT825ADB I I I 1 I I I 5962-88674013X I 61772 I IDT54FCT825ALB I I , A 5962-88674 REVfSONLEEL SHEET 14 i I I I 1 I I I I I I I 1 5962-8867402KX 1 61772 I IDT54FCT825BEB 1 I I I 5962-8867402LX 1 61772 I IDT54FCT825BDB I I 596288674023X I 61772 I IDT54FCT825BLB 1 I I I I I
19、 - 1/ Caution. Do not use this number for item - acquisition, Items acquired o this number may not satisfy the performance requirements of this drawing. Vendor CAGE humber 61712 Vendor name and address Integrated Device Techno1 ogy, Incorporated 3236 Scott Boulevard Santa Clara, CA 95054 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
