1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device types 05 and 06. Add case outline letter H. Make changes to 1.2.1, 1.2.2, 1.3, 1.4, table I, figure 1, and throughout. 92-11-16 M. A. FRYE B Changes in accordance with N.O.R. 5962-R189-95. 95-08-16 M. FRYE C Drawing being updated to re
2、flect current requirements. - ro 01-06-18 R. MONNIN D Modify drawing to current requirements. -rrp 11-01-13 C. SAFFLE THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY RICK
3、C. OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY CHARLES E. BESORE APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, DUAL, PRECISIO
4、N OPERATIONAL AMPLIFIER, MONOLITHIC SILICON DRAWING APPROVAL DATE 91-06-27 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-89494 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E112-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRC
5、UIT DRAWING SIZE A 5962-89494 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2
6、 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-89494 01 H A Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic n
7、umber Circuit function 01 TLC272 Precision dual operational amplifier 02 TLC277 Precision dual operational amplifier 03 TLC27L2 Precision dual operational amplifier, low power 04 TLC27L7 Precision dual operational amplifier, low power 05 TLC27M2 Precision dual operational amplifier, medium power 06
8、TLC27M7 Precision dual operational amplifier, medium power 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style H GDFP1-F10 or CDFP2-F10 10 Flat pack P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 2 CQCC1-N2
9、0 20 Square leadless chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage (VDD) 18 V dc Differential input voltage (VID) . VDDInput voltage range (VIN) -0.3 V dc to VDDInput voltage, peak to peak (VIPP) 5.5 V Input
10、 current (any input) (IIN) . 5 mA Output current (each output) (IO) 30 mA Total current into VDDterminal . 45 mA Total current out of ground terminal 45 mA Output short circuit duration Unlimited 1/ 1/ Short circuit may be to ground or either power supply. Rating applied to +25C ambient temperature.
11、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89494 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings continued. Power dissipation
12、(PD): Case H 675 mW at TA= +25C 2/ Case P . 1050 mW at TA= +25C 2/ Case 2 . 1375 mW at TA= +25C 2/ Storage temperature range . -65C to +150C Lead temperature (soldering, 60 seconds) +260C Junction temperature (TJ) . +150C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 1.4 Recommended o
13、perating conditions. Supply voltage range (VDD) 4 V dc to 16 V dc Common mode input voltage (VCM): VDD= 5 V +3.5 V dc maximum VDD= 10 V +8.5 V dc maximum Unity gain bandwidth (TA= +25C): VDD= 5 V (devices 01 and 02) 1.5 MHz VDD= 10 V (devices 01 and 02) 2.0 MHz VDD= 5 V (devices 03 and 04) 85 kHz VD
14、D= 10 V (devices 03 and 04) 110 kHz VDD= 5 V (devices 05 and 06) 525 kHz VDD= 10 V (devices 05 and 06) 635 kHz Source resistance (RS) . 50 Gain (AV) . 1 Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The follow
15、ing specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, G
16、eneral Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircui
17、t Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2/ For case outline H derate at 5.4 mW/C above TA= +25C, for case outline P derate at
18、 8.4 mW/C above TA= +25C, and for case outline 2 derate at 12 mW/C above TA= +25C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89494 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET
19、4 DSCC FORM 2234 APR 97 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been
20、obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qu
21、alified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Qua
22、lity Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to
23、identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Termin
24、al connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Ele
25、ctrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 h
26、erein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” sh
27、all be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of
28、compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturers product m
29、eets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification o
30、f change to DLA Land and Maritime -VA shall be required for any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime s agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation
31、. Offshore documentation shall be made available onshore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89494 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D S
32、HEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max Input offset voltage VIOVDD= 5 V, VO= 1.4 V, 1 01,03,05 10 mV VCM= 0 V, RS= 50 2,3 12 4 02,04,06 500 V
33、 2,3 3750 VDD= 10 V, VO= 1.4 V, 1 01,03,05 10 mV VCM= 0 V, RS= 50 2,3 12 4 02,04,06 800 V 2,3 4300 Input offset current (+IIN- -IIN) IIOVDD= 5 V, VO= 2.5 V, 1 All 0.100 nA VCM= 2.5 V 2 15 VDD= 10 V, VO= 5 V, 1 0.100 VCM= 5 V 2 15 Input bias current (+IIB+ -IIB) / 2 IIBVDD= 5 V, VO= 2.5 V, 1 All 0.15
34、0 nA VCM= 2.5 V 2 35 VDD= 10 V, VO= 5 V, 1 0.150 VCM= 5 V 2 35 Common mode input 3/ voltage input VCMRVDD= 5 V 1 All 0 to 4 V 2,3 0 to 3.5 VDD= 10 V 1 0 to 9 2,3 0 to 8.5 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
35、STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89494 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type L
36、imits 2/ Unit Min Max High level output voltage VOHVDD= 5 V, VID= 100 mV 1 All 3.2 V 2,3 3 VDD= 10 V, VID= 100 mV 1 8 2,3 7.8 Low level output voltage VOLVDD= 5 V, VID= -100 mV, IOL= 0 mA 1,2,3 All 50 mV VDD= 10 V, VID= -100 mV, IOL= 0 mA 50 Large signal differential voltage gain AVDVDD= 5 V, 4 01,0
37、2 5 V/mV VO= 0.25 V to 2 V 5,6 3.5 4 03,04 50 5,6 25 4 05,06 25 5,6 15 VDD= 10 V, 4 01,02 10 VO= 1 V to 6 V 5,6 7 4 03,04 50 5,6 25 4 05,06 25 5,6 15 Common mode rejection ratio CMRR VDD= 5 V, 1 All 65 dB VCM= VCMRminimum 2,3 60 VDD= 10 V, 1 65 VCM= VCMRminimum 2,3 60 See footnotes at end of table.
38、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89494 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued.
39、Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max Power supply rejection ratio PSRR VDD= 5 V to 10 V, 1 01,02 65 dB VO= 1.4 V 2,3 60 1 03,04,05,06 70 2,3 60 Supply current (two amplifiers) IDDVDD= 5 V, VO= 2.5 V, 1 01,02 3.2 mA VC
40、M= 2.5 V, no load 2 2.2 3 5 1 03,04 34 A 2 24 3 60 1 05,06 560 2 360 3 880 VDD= 10 V, VO= 5 V, 1 01,02 4 mA VCM= 5 V, no load 2 2.8 3 6 1 03,04 46 A 2 30 3 98 1 05,06 600 2 480 3 1000 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license
41、from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89494 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups
42、Device type Limits 2/ Unit Min Max Slew rate at unity gain SR VDD= 10 V, CL= 100 pF, 1 01,02 2.8 V/s VIPP= 5.5 V, AV= 1, 2 1.68 measured at 1.6 V and 3 3.8 4.3 V 1 03,04 0.02 2 0.01 3 0.03 1 05,06 0.25 2 0.15 3 0.35 1/ RL= 10 k for device types 01 and 02. RL= 1 M for device types 03 and 04. RL= 100
43、k for device types 05 and 06. 2/ The limiting terms “min” (minimum) and “max” (maximum) shall be considered to apply to magnitudes only. Negative current shall be defined as conventional current flow out of a device terminal. 3/ This range also applies to each input individually. 4. VERIFICATION 4.1
44、 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional
45、 criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall
46、 specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tes
47、ts prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89494 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 9 DSCC FORM
48、 2234 APR 97 Device types 01,02,03,04,05,06 Case outlines H P 2 Terminal number Terminal symbol 1 NC OUTPUT 1 NC 2 OUTPUT 1 -INPUT 1 OUTPUT 1 3 -INPUT 1 +INPUT 1 NC 4 +INPUT 1 GND NC 5 GND +INPUT 2 -INPUT 1 6 +INPUT 2 -INPUT 2 NC 7 -INPUT 2 OUTPUT 2 +INPUT 1 8 OUTPUT 2 VDDNC 9 VDD- NC 10 NC - GND 11 - - NC 12 - - +INPUT 2 13 - - NC 14 - - NC 15 - - -INPUT 2 16 - - NC 17 - - OUTPUT 2 18 - -
