1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add vendor CAGE F8859. Add device Class V criteria. Add delta limits, table III. Add case outline X. Update boilerplate to MIL-PRF-38535 requirements. lgt 01-05-10 Raymond Monnin B Update boilerplate paragraphs to the current MIL-PRF-38535 requir
2、ements. - LTG 09-08-12 Thomas M. Hess REV SHET REV B B B B SHEET 15 16 17 18 REV STATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Monica L. Poelking DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MI
3、CROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Raymond Monnin APPROVED BY Michael A. Frye MICROCIRCUIT, DIGITAL, ADVANCED CMOS, SYNCHRONOUS PRESETTABLE BINARY COUNTER, MONOLITHIC SILICON DRAWING APPROVAL DATE 89-06-05 AMSC
4、 N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-89582 SHEET 1 OF 18 DSCC FORM 2233 APR 97 5962-E310-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89582 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 432
5、18-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are refle
6、cted in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following examples. For device classes M and Q: 5962 - 89582 01 E A Federal stock class designator RHA designator (see 1.2.
7、1) Device type (see 1.2.2)Case outline (see 1.2.4)Lead finish (see 1.2.5) / /Drawing number For device class V: 5962 - 89582 01 V X A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Leadfinish (see 1.2.5) / (see 1.2.3)
8、/Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriat
9、e RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54AC163 Synchronous presettable binary counter 1.2.3 Device class designator. The device class designator is a si
10、ngle letter identifying the product assurance level as listed below. Since the device class designator has been added after the original issuance of this drawing, device classes M and Q designators will not be included in the PIN and will not be marked on the device. Device class Device requirements
11、 documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 Provided by IHSNot for ResaleNo reproduction or networking permitted with
12、out license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89582 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive des
13、ignator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line F GDFP2-F16 or CDFP3-F16 16 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier X CDFP4-F16 16 Flat pack 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendi
14、x A for device class M. 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) -0.5 V dc to +7.0 V dc DC input voltage range (VIN) -0.5 V dc to VCC + 0.5 V dc DC output voltage range (VOUT) . -0.5 V dc to VCC+ 0.5 V dc Clamp diode current (IIK, IOK) . 20 mA DC output current 50 mA DC VCCo
15、r GND current (per pin) . 50 mA Storage temperature range (TSTG) . -65C to +150C Maximum power dissipation (PD) . 500 mW Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) . +175C 4/ 1.4 Recommended operating conditio
16、ns. 2/ 3/ 5/ Supply voltage range (VCC) +2.0 V dc to +6.0 V dc Input voltage range (VIN) +0.0 V dc to VCCOutput voltage range (VOUT) . +0.0 V dc to VCCCase operating temperature range (TC) . -55C to +125C Input rise or fall times (V/t): VCC= 3.6 V . 0 to10 ns VCC= 5.5 V . 0 to 8 ns _ 1/ Stresses abo
17、ve the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full
18、 specified VCCrange and case temperature range of -55C to +125C. 4/ Maximum junction temperature shall not be exceeded except for allowable short duration burn-in screening conditions in accordance with method 5004 of MIL-STD-883. 5/ Operation from 2.0 V dc to 3.0 V dc is provided for compatibility
19、with data retention and battery back-up systems. Data retention implies no input transition and no stored data loss with the following conditions: VIH 70% VCC, VIL 30% VCC, VOH 70% VCC -20A, VOL 30% VCC 20 A. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I
20、HS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89582 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
21、part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STA
22、NDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are availabl
23、e online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise
24、specified, the issues of these documents cited in the solicitation or contract. ELECTRONIC INDUSTRIES ALLIANCE (EIA) JEDEC Standard No. 20 - Standard for Description of 54/74ACXXXXX and 54/74ACTXXXXX Advanced High-Speed CMOS Devices. (Copies of these documents are available online at http:/www.jedec
25、.org or from Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834). 2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersede
26、s applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Man
27、agement (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, constru
28、ction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein.
29、3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. Provided by IHSNot for ResaleNo reproduction or networking permitted
30、 without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89582 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 3.2.5 Counting sequence. The counting sequence shall be as specified on figure 4. 3.2.6 Switching waveforms and test c
31、ircuit. The switching waveforms and test circuit shall be as specified on figure 5. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in
32、table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN l
33、isted in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designato
34、r shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as r
35、equired in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requiremen
36、ts of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved so
37、urce of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as
38、 required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.
39、2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required
40、documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 40 (see MIL-PRF-38535, appendix A). Provided by IHSNot for
41、ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89582 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test and MIL-STD-883 tes
42、t method 1/ Symbol Test conditions 2/ -55C TC +125C +3.0 V VCC +5.5 V Device type and VCCGroup A subgroups Limits 3/ Unitunless otherwise specified device class Min Max Positive input clamp voltage 3022 VIC+For input under test IIN= 1.0 mA All V 0.0 V 1 0.4 1.5 V Negative input clamp voltage 3022 VI
43、C-For input under test IIN= -1.0 mA All V Open 1 -0.4 -1.5 V High level output voltage 3006 VOH 4/ VIN= VIHminimum or VILmaximum IOH= -50 A All All 3.0 V 1, 2, 3 2.9 V All All 4.5 V 4.4 All All 5.5 V 5.4 VIN= VIHminimum or VILmaximum IOH= -12 mA All All 3.0 V 1 2.56 2, 3 2.4 VIN= VIHminimum or VILma
44、ximum IOH= -24 mA All 4.5 V 1 3.86 All 2, 3 3.7All 5.5 V 1 4.86 All 2, 3 4.7VIN= VIHminimum or VILmaximum IOH= -50 mA All All 5.5 V 1, 2, 3 3.85 Low level output voltage 3007 VOL 4/ VIN= VIHminimum or VILmaximum IOL= 50 A All All 3.0 V 1, 2, 3 0.1 V All All 4.5 V 0.1 All All 5.5 V 0.1 VIN= VIHminimu
45、m or VILmaximum IOL= 12 mA All All 3.0 V 1 0.36 2, 3 0.5 VIN= VIHminimum or VILmaximum IOL= 24 mA All All 4.5 V 1 0.36 2, 3 0.5 All All 5.5 V 1 0.36 2, 3 0.5 VIN= VIHminimum or VILmaximum IOL= 50 mA All All 5.5 V 1, 2, 3 1.65 High level input voltage VIH5/ All All 3.0 V 1, 2, 3 2.1 V All All 4.5 V 3
46、.15 All All 5.5 V 3.85 Low level input voltage VIL5/ All All 3.0 V 1, 2, 3 0.9 V All All 4.5 V 1.35 All All 5.5 V 1.65 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89582 DEFE
47、NSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +3.0 V VCC +5.5 V Device type and VCCGroup A subgroups Limits 3/
48、Unit unless otherwise specified device class Min Max Input leakage current low 3009 IILVIN= 0.0 V All All 5.5 V 1 -0.1 A 2, 3 -1.0 Input leakage current high 3010 IIHVIN= 5.5 V All All 5.5 V 1 0.1 A 2, 3 1.0 Quiescent supply current, output high 3005 ICCHVIN= VCCor GND IO= 0 A All All 5.5 V 1 4 A 2, 3 80 Quiescent supply current, output low 3005 ICCLVIN= VCCor GND IO= 0 A All All 5.5 V 1 4 A 2, 3 80 Input capacitance 3012 CINSee 4.4.1c TC= +25C All All 5.0 V 4 8.0 pF Power dissipation capacitance CPD6/ See 4.4.1c TC= +25C, f = 1
