1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Added CMRR test to table I. Updated document to current MIL-H-38534 requirements. Editorial changes throughout. 91-10-24 G. A. Lude B Changes in accordance with NOR 5962-R243-97. 97-03-13 Kendall A. Cottongim C Add CAGE code 1HBD3. Removed vendor
2、 CAGE 62839. Made corrections to table I. Editorial changes throughout. -sld 00-06-07 Raymond Monnin D Update drawing. 06-02-22 Raymond Monnin REV SHEET REV SHEET REV STATUS REV D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Gary Zahn DEFENSE SUPPLY CENTER COLUMBU
3、S STANDARD MICROCIRCUIT DRAWING CHECKED BY Michael C. Jones POST OFFICE BOX 3990 COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Gregory Lude MICROCIRCUIT, HYBRID, LINEAR, WIDEBAND, OPERATIONAL AMPLIFIER AND AGENCIES OF THE DEPARTMENT
4、 OF DEFENSE DRAWING APPROVAL DATE 90-12-06 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-89858 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E283-06Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89858 DEF
5、ENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents one product assurance class, class H (high reliability) and a choice of case outlines and lead finishes are available and are reflected in the Part or Ident
6、ifying Number (PIN). 1.2 PIN. The PIN shall be as shown in the following example: 5962-89858 01 X X Drawing number Device type Case outline Lead finish (see 1.2.1) (see 1.2.2) (see 1.2.3) 1.2.1 Device type(s). The device type(s) shall identify the circuit function as follows: Device type Generic num
7、ber 1/ Circuit function 01 CLC206A, KH206A Wideband, overdrive protected, operational amplifier 1.2.2 Case outline(s). The case outline(s) shall be as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 12 Can package 1.2.3 Lead fin
8、ish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 2/ Supply voltage (VCC) . 20 V dc Differential input voltage 3 V dc Common mode input voltage. (VCC - 1) V Output current . 150 mA Storage temperature range . -65C to +150C Lead temperature (soldering, 10 seco
9、nds) +300C Junction temperature (TJ) . +175C Power dissipation (PD) 3/ Thermal resistance, case-to-ambient (CA) 65C/W 4/ Thermal resistance, junction-to-case: JC(circuit) 17.5C/W 5/ JC(output) 100C/W 6/ 1/ The CLC206A is not available from an approved source of supply. 2/ Stresses above the absolute
10、 maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 3/ The power dissipation can be determined based on the application and junction temperature verified to be TJ +175C and using the thermal resistance va
11、lues given. 4/ Still air, no heat sink. 5/ Thermal resistance of circuit; PCIRCUIT= 2(VCC) ICC. 6/ Thermal resistance of output transistors; POUTPUT= VCE(IE) x (% duty cycle). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAW
12、ING SIZE A 5962-89858 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.4 Recommended operating conditions. Supply voltage range. 5 V dc to 15 V dc Gain range. +7 to +50; -1 to -50 Common mode input voltage. (VCC - 5 ) V Output current . 100 mA
13、 Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these
14、documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component
15、 Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Doc
16、ument Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable l
17、aws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device class H shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as des
18、ignated in the device manufacturers Quality Management (QM) plan or as designated for applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device
19、class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1
20、 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT
21、 DRAWING SIZE A 5962-89858 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply ove
22、r the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with
23、 MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the elect
24、rical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under docum
25、ent revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) su
26、bmitted to DSCC-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. Provide
27、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89858 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits T
28、est Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Min Max Unit 4, 6 150 Small signal bandwidth (-3 dB bandwidth) SSBW VOUT40 MHz 5 01 0.8 dB Gain flatness rolloff GFR f = 75 MHz 4, 5, 6 01 0.7 dB 4 1.5 Linear phase deviation 2/ LPD f 5.0 MHz 8A 01 -153 dB
29、m (1 Hz) 7, 8B 55 Integrated noise 2/ INV f = 5.0 kHz to 150 MHz 8A 01 61 V 1, 3 8.0 Input offset voltage VIO2 01 11.0 mV Input offset voltage 2/ temperature coefficient VIO T 1, 2, 3 01 25 V/C Output voltage range 2/ VO No load 1, 2, 3 01 -11 +11 V 1, 2 20 + Input bias current +IIBInput resistance
30、is 100 k 3 01 30 A + Input bias current 2/ temperature coefficient +IIB T 1, 2, 3 01 125 nA/C 1 10 2 30 - Input bias current -IIBInput resistance is 100 k 3 01 26 A - Input bias current 2/ temperature coefficient -IIB T 1, 2, 3 01 200 nA/C See footnotes at end of table. Provided by IHSNot for Resale
31、No reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89858 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol
32、 Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Min Max Unit Power supply rejection ratio PSRR VCC= 0.5 V 1, 2, 3 01 55 dB Common mode rejection 2/ ratio CMRR VCM= 1 V 4, 5, 6 01 50 dB Supply current ICCNo load 1, 3 01 31 mA 2 33 Internal feedback 2/ resistance A
33、bsolute tolerance RFA 4 01 0.2% Temperature coefficient RFTC 4 01 -60 -140 ppm/C 1/ Unless otherwise specified, RL= 200 ohms, RF= 2,000 ohms, VCC= 15 V, AV= +20. 2/ Parameter shall be tested as part of device initial characterization and after design and process changes which may affect this paramet
34、er. Parameter shall be guaranteed to the limits specified in table I for all lots not specifically tested. 3/ dBc is a standard reference for a signal referenced to a carrier signal level. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICR
35、OCIRCUIT DRAWING SIZE A 5962-89858 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 Case outline X. Inches Millimeters Symbol Min Max Min Max Notes A .148 .181 3.76 4.60 b .016 .019 0.41 0.48 D .595 .608 15.11 15.44 D1 .545 .555 13.84 14.10 e .4
36、00 BSC 10.16 BSC 5 e1 .200 BSC 5.08 BSC 5 e2 .100 BSC 2.54 BSC 5 F .030 0.76 k .026 .036 0.66 0.91 k1 .026 .036 0.66 0.91 4 L .310 .340 7.87 8.64 45 BSC 45 BSC 5 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. The product may be measured by direct
37、 methods or by gauge. 4. Measured from the maximum diameter of the product. 5. Leads having a maximum diameter .019 (0.48 mm) measured in gauging plane .054 (1.37 mm) +.001 (0.03 mm), -.000 (0.00 mm) below the base plane of the product shall be within .007 (0.18 mm) of their true position relative t
38、o a maximum width tab. FIGURE 1. Case outline(s). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89858 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 9 DSCC FORM 2234 APR 97
39、Device type 01 Case outline X Terminal number Terminal symbol 1 +VCC(supply voltage) 2 No connection 3 GND (case and bias) 4 No connection 5 -VIN 6 +VIN7 GND (case and bias) 8 Rf(internal feedback) 9 -VCC(supply voltage) 10 -VCC(collector supply) 11 VOUT12 +VCC(collector supply) NOTE: Pin 8 provides
40、 access to a 2 k resistor which can be connected to the output or left open if an external feedback resistor is desired. FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89858 D
41、EFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 10 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements Subgroups (in accordance with MIL-PRF-38534, group A test table) Interim electrical parameters 1 Final electrical parameters
42、 1*,2,3,4,7 Group A test requirements 1,2,3,4,5,6,7,8A,8B Group C end-point electrical parameters 1 * PDA applies to subgroup 1. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Qualit
43、y Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition
44、A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable,
45、in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TAas specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are
46、 optional at the discretion of the manufacturer. 4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance with MIL-PRF-38534 and as specified herein. 4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF
47、-38534 and as follows: a. Tests shall be as specified in table II herein. b. Subgroups 9, 10, and 11 shall be omitted. 4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro
48、m IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89858 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 11 DSCC FORM 2234 APR 97 4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows: a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test, method 1005 of MIL-ST
