1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. - ro 00-08-31 R. MONNIN B Replaced reference to MIL-STD-973 with reference to MIL-PRF-38535. - ro 03-04-14 R. MONNIN C Update drawing to current MIL-PRF-38535 requirements. -rrp 13-07-22 C. SAFFLE
2、THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY RICK C. OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICRO
3、CIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY CHARLES E. BESORE APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, DUAL POWER SUPPLY SUPERVISORS, MONOLITHIC SILICON DRAWING APPROVAL DATE 90-12-18 AMSC N/A REVISION LEVEL C SIZ
4、E A CAGE CODE 67268 5962-90932 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E487-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90932 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 D
5、SCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device class Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Numb
6、er (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 90932 01 M E A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline
7、 (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A spe
8、cified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 TL7770-5M Dual power-supply supervisors 02 TL7770-12M Dual po
9、wer-supply supervisors 03 TL7770-15M Dual power-supply supervisors 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-
10、STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Pac
11、kage style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking p
12、ermitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90932 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage (VCC) . 20 V dc 2/ Input voltage range (VI): VSU1, VSU2, VS01, VS02 -0.
13、3 V dc to +18 V dc Low level output current (IOL), ( RESET1 and RESET2 ) 20 mA High level output current (IOH), (RESET1 and RESET2) -20 mA Storage temperature range -65C to +150C Lead temperature soldering, 1.6 mm (0.0625 inch) from case for 10 seconds 260C Power dissipation (PD) 1375 mW 3/ Junction
14、 temperature . -55C to +150C Thermal resistance, junction-to-case (JC) See MIL-STD-1835 1.4 Recommended operating conditions. Supply voltage (VCC) . 3.5 V dc minimum, 18 V dc maximum Input voltage range (VI): (RESIN1, RESIN2 , VSU1, VSU2, VS01, VS02) 0 V dc minimum, 18 V dc maximum Output voltage (V
15、O), (CT1 and CT2) . 5 V dc maximum Output sink current (IO), (CT1 and CT2) 50 A maximum High level output current (IOH), (RESET1 and RESET2) -16 mA maximum Low level output current (IOL), ( RESET1 and RESET2 ) 16 mA maximum Continuous output current (IO), (SCR1 GATE DRIVE and SCR2 GATE DRIVE) 25 mA
16、maximum Ambient operating temperature range ( TA) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of
17、these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Elec
18、tronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/quicksearch.dla.mil/ or from the Standardization Document Order Desk, 700 Rob
19、bins Avenue, Building 4D, Philadelphia, PA 19111-5094.) _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. method 1019, condition A. 2/ All voltage values are with respect
20、to the network ground terminal. 3/ Above TA= +25C derate at a factor of 12.0 mW/C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90932 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET
21、4 DSCC FORM 2234 APR 97 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been
22、obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 as specified herein, or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the fo
23、rm, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dim
24、ensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified
25、 on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance
26、 characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup
27、 are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking th
28、e “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. T
29、he certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be requi
30、red from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The cert
31、ificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF
32、-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of chang
33、e for device class M. For device class M, notification to DLA Land and Maritime-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and M
34、aritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M.
35、 Device class M devices covered by this drawing shall be in microcircuit group number 88 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90932 DLA LAND AND MARITIME COLUMBUS,
36、OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C VCC= 3.5 V to 18 V Group A subgroups Device type Limits Unit unless otherwise specified Min Max High level output VOHIOH= -15 mA 1,2,3 All VCCV voltage
37、, RESET -1.5 High level output VOHIOH= -20 mA 1,2,3 All VCCV voltage, SCR, -1.5 GATE DRIVER Low level output VOLIOL= 15 mA 1,2,3 All 0.4 V voltage, RESET Undervoltage VT-1 01 4.50 4.632 V threshold (negative 2,3 4.40 4.646 going), VSU1 1 02 10.80 11.07 2,3 10.62 11.12 1 03 13.50 13.866 2,3 13.36 13.
38、916 Undervoltage threshold (negative VT- 1 All 1.485 1.527 V going), VSU2 2,3 1.460 1.542 Overvoltage VT+1 All 2.530 2.630 V threshold 2,3 2.480 2.680 Input current, IIVI= 5.5 V or 0.4 V 1,2,3 All -10 A RESIN Input current, VSO IIVI= 2.4 V 1,2,3 All 2 A High level output IOHVO= VCC1,2,3 All 50 A cur
39、rent, RESET Low level output IOLVO= 1 V 1,2,3 All -50 A current, RESET Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90932 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM
40、2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C VCC= 3.5 V to 18 V Group A subgroups Device type Limits Unit unless otherwise specified Min Max Peak output current, IOPDuration = 1 ms 1,2,3 All -250 mA SCR GATE DRIVE Supply current ICCVSU1
41、and VSU2 at VT+, 1 All 5 mA RESIN1 and RESIN2 at VCC, VS01 and VS02 at 0 V 2,3 6.5 Functional tests See 4.4.1c 7,8 All Propagation delay 1/ tPLHSee figure 4, TA= +25C 9 All 500 ns time, low-to-high level output from RESIN to RESET Propagation delay 1/ tPHLSee figure 4, TA= +25C 9 All 500 ns time, hi
42、gh-to-low level output from RESIN to RESET Rise time, 1/ tRSee figure 4, TA= +25C 9 All 75 ns RESET Fall time, 1/ tFSee figure 4, TA= +25C 9 All 50 ns RESET 1/ If not tested, shall be guaranteed to the limits specified in table I herein. Provided by IHSNot for ResaleNo reproduction or networking per
43、mitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90932 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Device types 01, 02, 03 Case outlines E 2 Terminal number Terminal symbol 1 RESIN 1 NC 2 CT1 RESIN 1 3 RESET1 CT1 4 RESET
44、 1 RESET1 5 VSU1 RESET 1 6 VS01 NC 7 SCR DRIVE1 VSU1 8 GND VS01 9 SCR DRIVE2 SCR DRIVE1 10 VS02 GND 11 VSU2 NC 12 RESET 2 SCR DRIVE2 13 RESET2 VS02 14 CT2 VSU2 15 RESIN 2 RESET 2 16 VCCNC 17 - RESET2 18 - CT2 19 - RESIN 2 20 - VCCNC = No connection FIGURE 1. Terminal connections. Provided by IHSNot
45、for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90932 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Input Output VSU RESIN RESET RESET X L H L VT+H L H X = Dont care H = High L =
46、 Low FIGURE 2. Truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90932 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 Device VSU1 VSU2 R1 R2 R1 R2 01
47、 11.66 k 6 k Short Open 02 35 k 6 k Short Open 03 45 k 6 k Short Open FIGURE 3. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90932 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LE
48、VEL C SHEET 10 DSCC FORM 2234 APR 97 NOTE: Includes jig and probe capacitance. FIGURE 4. RESET and RESET output test circuits. _ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90932 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 11 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and i
