1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes are in accordance with the notice of revision 5962-R221-93. - phn 93-09-09 Monica L. Poelking B Changes are in accordance with the notice of revision 5962-R206-96. - bjm 96-09-03 Monica L. Poelking C Redrawn with changes. Update the boile
2、rplate to the current requirements of MIL-PRF-38535. - jak 08-04-07 Thomas M. Hess D Correct test condition for total supply current (ICCT) and add footnote 12/ and modify footnote 15/ in table I. Update boilerplate paragraphs as specified in current requirements of MIL-PRF-38535. MAA. 09-12-14 Thom
3、as M. Hess REV SHET REV D D D D D SHEET 15 16 17 18 19 REV STATUS REV D D D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Phu H. Nguyen DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING CHECKED
4、BY Thomas J. Ricciuti THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, FAST CMOS, 10-BIT BUS INTERFACE D-REGISTERS WITH THREE-STATE OUTPUTS, TTL COMPATIBLE INPUTS AND LIMITED OUTPUT VOLTAGE SWING, MONOLITHIC SILICON AND AGENCIES OF THE DEPART
5、MENT OF DEFENSE DRAWING APPROVAL DATE 93-07-12 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-92225 SHEET 1 OF 19 DSCC FORM 2233 APR 97 5962-E066-10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-9222
6、5 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case out
7、lines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 92225 01 M K A Federal stock class designator
8、RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Leadfinish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA
9、designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic numb
10、er Circuit function 01, 02 54FCT821AT 10-bit bus interface D registers with three-state outputs, TTL compatible inputs and limited output voltage swing 03, 04 54FCT821BT 10-bit bus interface D registers with three-state outputs, TTL compatible inputs and limited output voltage swing05, 06 54FCT821CT
11、 10-bit bus interface D registers with three-state outputs, TTL compatible inputs and limited output voltage swing 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor
12、 self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Out
13、line letter Descriptive designator Terminals Package style K GDFP2-F24 or CDFP3-T24 24 Flat pack L GDIP3-T24 or CDIP4-T24 24 Dual-in-line 3 CQCC1-N28 28 Leadless-chip-carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A f
14、or device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92225 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1
15、/ 2/ 3/ . Supply voltage range (VCC) . -0.5 V dc to +7.0 V dc DC input voltage range (VIN) -0.5 V dc to VCC+ 0.5 V dc 4/ DC output voltage range (VOUT) -0.5 V dc to VCC+ 0.5 V dc 4/ DC input clamp current (IIK) (VIN= -0.5 V ) -20 mA DC output clamp current (IOK) (VOUT-0.5 V and +7.0 V) . 20 mA DC ou
16、tput source current (IOH) (per output) -30 mA DC output sink current (IOL) (per output) . +70 mA DC VCCcurrent (ICC) . 260 mA Ground current (IGND) +550 mA Storage temperature range (TSTG) -65C to +150C Case temperature under bias (TBIAS) -65C to +135C Maximum power dissipation (PD) 500 mW Lead temp
17、erature (soldering, 10 seconds) . +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) . +175C 1.4 Recommended operating conditions. 2/ 3/ Supply voltage range (VCC) +4.5 V dc to +5.5 V dc Input voltage range (VIN) +0.0 V dc to VCCOutput voltage range (VOUT) .
18、 +0.0 V dc to VCCMaximum low level input voltage (VIL) . 0.8 V Minimum high level input voltage (VIH) . 2.0 V Case operating temperature range (TC) . -55C to +125C Maximum input rise or fall rate (t/V): (from VIN= 0.3 V to 2.7 V, 2.7 V to 0.3 V) 5 ns/V Maximum high level output current (IOH): Device
19、 type 01, 03, and 05 . -6 mA Device type 02, 04, and 06 . -12 mA Maximum low level output current (IOL) +32 mA 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless ot
20、herwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VCCrange and case temperature range of -55C to +125C. 4/ For VCC 6.5 V, the upper limit on the range is limited to 7.0 V. Provided by IHSNot for ResaleNo reproduct
21、ion or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92225 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The followi
22、ng specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, Ge
23、neral Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit
24、 Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing a
25、nd the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V s
26、hall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in a
27、ccordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appe
28、ndix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. Th
29、e logic diagram shall be as specified on figure 3. 3.2.5 Ground bounce load circuit and waveforms. The ground bounce load circuit and waveforms shall be as specified on figure 4. 3.2.6 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 5. P
30、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92225 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics and post
31、irradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requireme
32、nts shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is
33、not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall
34、 be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certifica
35、te of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order t
36、o be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-
37、PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lo
38、t of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review
39、for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment
40、 for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 37 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92225 DEFENSE SUPP
41、LY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +4.5 V VCC +5.5 V unless otherwise specified Device type VCCGroup A subgroups Limit
42、s 3/ Unit Min Max High level output voltage 3006 VOH14/ For all inputs affecting output under test VIH= 2.0 V or VIL= 0.8 V For all other inputs VIN= VCCor GND IOH= -300 A 01, 03, 05 4.5 V 1, 2, 3 2.7 VCC-0.5 V 02, 04, 06 3.0 VCC-0.5VOH2For all inputs affecting output under test VIH= 2.0 V or VIL= 0
43、.8 VFor all other inputs VIN= VCCor GND IOH= -6 mA 01, 03, 05 4.5 V 1, 2, 3 2.4 VCC-0.5 V IOH= -12 mA 2.0 VCC-0.5IOH= -12 mA02, 04, 06 2.4 VCC-0.5Low level output voltage 3007 VOL14/ For all inputs affecting output under test VIH= 2.0 V or VIL= 0.8 V For all other inputs VIN= VCCor GND IOL= +300 A A
44、ll 4.5 V 1, 2, 3 0.20 V VOL2For all inputs affecting output under test VIH= 2.0 V or VIL= 0.8 V For all other inputs VIN= VCCor GND IOL= +32 mA All 4.5 V 1, 2, 3 0.55 V Three-state output leakage current high 3021 IOZH5/ 6/ OEnullnullnullnull= VIHor VILVIH= 2.0 V, VIL= 0.8 V For all other inputs, VI
45、N = VCCor GND VOUT= VCC01, 03, 05 5.5 V 1, 2 0.1 A 3 10.0 02, 04, 06 1, 2 0.1 3 2.0 Three-state output leakage current low 3020 IOZL5/ 6/ OEnullnullnullnull= VIHor VILVIH= 2.0 V, VIL= 0.8 V For all other inputs, VIN = VCCor GND VOUT= GND 01, 03, 05 5.5 V 1, 2 -1.0 A 3 -10.0 02, 04, 06 1, 2 -0.1 3 -1
46、0.0 Negative input clamp voltage 3022 VIC-For input under test, IIN= -18 mA 01, 03, 05 4.5 V 1, 2, 3 -1.2 V For input under test, IIN= -15 mA 02, 04, 06 -1.3 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICR
47、OCIRCUIT DRAWING SIZE A 5962-92225 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +4.5 V VCC +5.5 V unless
48、 otherwise specified Device type VCCGroup A subgroups Limits 3/ Unit Min Max Input current high 3010 IIHFor input under test, VIN= VCCFor all other inputs, VIN= VCCor GND 01, 03, 05 5.5 V 1, 2 1.0 A 3 5.0 02, 04, 06 5.5 V 1, 2 0.1 A 3 1.0 Input current low 3009 IILFor input under test, VIN= GND For all other inputs, VIN= VCCor GND 01, 03, 05 5.5 V 1, 2 -1.0 A 3 -5.0 02, 04, 06 5.5 V 1, 2 -0.1 A 3 -1.0 Input capacitance 3012 CIN7/ See 4.4.1c TC= +25C All GND 4 10 pF Input/output capacitance 3012 COUT7/ See 4.4.1c TC= +25C All GND 4 12 pF Short circuit output c
