1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device type 03. Rewrite entire document 96-01-10 K. A. Cottongim B Update drawing boilerplate. 02-07-31 Raymond Monnin C Update drawing. -gz 07-04-10 Robert M. Heber REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C C OF SHEETS SHEET 1 2
2、 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Gary Zahn DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Michael C. Jones COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Kendall A Cottongim MICROCIRCUIT, HYBRID, DIG
3、ITAL-LINEAR, 14-BIT, SAMPLING ANALOG TO DIGITAL CONVERTER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 95-06-06 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-93198 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E345-07 Provided by IHSNot for ResaleNo reproduction or networking p
4、ermitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93198 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MI
5、L-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 93198
6、01 H X A Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 spec
7、ified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 ADS-944 14-bit, 5 MHz sampling, A/D converter 02 ADS-3018
8、9 14-bit, 5 MHz sampling, A/D converter 03 ADS-30214 14-bit, 5 MHz sampling, A/D converter 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certifi
9、cation as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality clas
10、s level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer sp
11、ecified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be
12、 specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow.
13、 This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93198 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 9
14、7 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 32 Dual-in-line 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Posi
15、tive supply voltage range (+VCC) . 0 V to +16 V dc Negative supply voltage range (-VEE). 0 V to -16 V dc Positive analog and digital supply voltage (+VDD) 0 V to +6 V dc Negative analog and digital supply voltage (-VDD) 0 V to -6 V dc Digital inputs -0.3 V dc to +VDD+ 0.3 V dc Analog input. -5 V dc
16、to +5 V dc Lead temperature (soldering, 10 seconds). +300C Power dissipation (PD) . 3.3 W Junction temperature (TJ) +175C Thermal resistance: Junction-to-case (JC). 7C/W Junction-to-ambient (JA) 28C/W Storage temperature -65C to +150C 1.4 Recommended operating conditions. Positive supply voltage ran
17、ge (+VCC). +14.25 V dc to +15.25 V dc Negative supply voltage range (-VEE) -14.25 V dc to -15.25 V dc Positive analog and digital supply voltage (+VDD) +4.75 V dc to +5.25 V dc 2/ Negative analog and digital supply voltage (-VDD) -4.95 V dc to -5.45 V dc 3/ Ambient operating temperature range (TA) -
18、55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation
19、 or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOO
20、KS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Buildin
21、g 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exempti
22、on has been obtained. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ +4.9 V dc minimum at TA= -55C. 3/ -5.1 V dc minimum at TA= -55C. Provided by IHSNot for ResaleNo
23、reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93198 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirement
24、s for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer
25、 may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicabl
26、e device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The te
27、rminal connections shall be as specified on figure 2. 3.2.3 Output coding table. The output coding table shall be as specified on figure 3. 3.2.4 Timing diagram. The timing diagram shall be as specified on figure 4. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the e
28、lectrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined i
29、n table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MI
30、L-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, a
31、nd for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer
32、 in order to supply to this drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-3853
33、4 shall be provided with each lot of microcircuits delivered to this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93198 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SH
34、EET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits Test Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device type Min Max Unit +ICC+VCC= +15.0 V dc +45 -IEE-VEE= -15.0 V dc -65 +IDD+VDD= +5.0 V dc +168 Power supply currents -IDD-VDD=
35、 -5.2 V dc 1, 2, 3 All -175 mA Power supply rejection ratios PSRR For each +VCC, -VEE, and VDD4, 5, 6 All 0.05 %FSR/ %V ANALOG INPUT Input voltage range VIN1, 2, 3 All 1.25 V Input resistance 2/ RIN4 All 500 DIGITAL INPUTS 2/ Logic “0“ VIH 1, 2, 3 All +2.0 V Logic “1“ VIL 1, 2, 3 All +0.8 V Logic lo
36、ading “1“ IIL 1, 2, 3 All +20 A Logic loading “0“ 3/ IIH1, 2, 3 All -20 A DIGITAL OUTPUTS 2/ Logic “0“ VOH 1, 2, 3 All +2.4 V Logic “1“ VOL 1, 2, 3 All +0.4 V Logic loading “1“ IOL 1, 2, 3 All +4 mA Logic loading “0“ 3/ IOH1, 2, 3 All -4 mA STATIC PERFORMANCE Resolution RES 4, 5, 6 All 14 Bits 4 -0.
37、95 +1.20 f = 10 kHz 5, 6 All -0.95 +1.50 Differential nonlinearity DNL f = 10 kHz, TC= -55C, 4/ VDD= -4.95 V dc and +4.80 V dc 6 03 -0.99 +1.50 LSB See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT D
38、RAWING SIZE A 5962-93198 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device type Min Ma
39、x Unit STATIC PERFORMANCE - Continued. 4 0.4 Full scale absolute accuracy 5, 6 All 0.8 %FSR 4 0.4 Bipolar offset error BPOE5, 6 All 0.9 %FSR 4 0.4 Gain error AE5, 6 All 1.5 %FSR DYNAMIC PERFORMANCE 4 -70 Peak harmonics (-0.5 dB) 1 MHz to 2.5 MHz 5, 6 All -61 dB 4 -68 Total harmonic distortion (-0.5
40、dB) 1 MHz to 2.5 MHz 5, 6 All -60 dB 4 73 Signal to noise ratio (-0.5 dB, without distortion) 1 MHz to 2.5 MHz 5, 6 01, 03 71 dB 4 68 Signal to noise ratio (-0.5 dB, with distortion) 1 MHz to 2.5 MHz 5, 6 All 62 dB Signal to noise ratio (DC to 100 kHz) SNR 98 kHz 4, 5, 6 02 75 dB 1/ +VCC= +14.25 V d
41、c to +15.75 V dc, -VEE= -14.25 V dc to -15.75 V dc, +VDD= +4.9 V dc to +5.25 V dc, -VDD= -5.1 V dc to -5.45 V dc. 2/ Parameter shall be tested as part of device initial characterization and after design and process changes. Parameter shall be guaranteed to the limits specified in table I for all lot
42、s not specifically tested. 3/ When Comp. bits (8 pin ) is low, logic loading “0“ will be -350 A for this pin. 4/ These test conditions are additional for device type 03 only. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWI
43、NG SIZE A 5962-93198 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Millimeters Inches Symbol Min. Max. Min. Max. A 5.97 .235 A1 4.32 .225 b 0.41 0.56 .016 .021 b2 0.89 1.14 .035 .045 c 0.23 0.38 .009 .015 D 42.93 43.69 1.69 1.
44、72 e 2.54 BSC 0.100 BSC E 27.43 28.19 1.08 1.11 eA 22.61 23.37 .89 .92 L 4.45 5.08 .175 .200 Q 0.38 0.89 .015 .035 S1 2.29 2.79 .09 .11 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving con
45、flicts between the metric and inch-pound units, the inch-pound units shall rule. FIGURE 1. Case outline(s). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93198 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO
46、43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Device types All Case outline X Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 +5 V analog supply -5.2 V digital supply Analog input Analog ground Offset adjust Analog gr
47、ound Gain adjust Comp. bits Output enable +5 V digital supply Analog ground +15 V supply -15 V supply -5.2 V analog supply Digital ground EOC Bit 14 (LSB) Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 (MSB) Bit 1 (MSB) Start convert FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93198 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 Output coding MSB LSB MSB LSB MSB LSB Input ran
