1、REVISIONSLTR DESCRIPTION DATE (YR-MO-DA) APPROVEDA Changes in accordance with NOR 5962-R333-97. 97-10-22 Monica L. PoelkingB Changes in accordance with NOR 5962-R165-98.98-09-02 Monica L. PoelkingC Update boilerplate to MIL-PRF-38535 and updated appendix A. Editorialchanges throughout. - tmh00-07-03
2、 Monica L. PoelkingREVSHEETREV CCCCCCCCSHEET 15 16 17 18 19 20 21 22REV STATUS REV CCCCCCCCCCCCCCOF SHETS SHET 123456789101121314PMIC N/A PREPARED BY Thanh V. NguyenDEFENSE SUPPLY CENTER COLUMBUSSTANDARDMICROCIRCUITDRAWINGCHECKED BYThanh V. NguyenCOLUMBUS, OHIO 43216THIS DRAWING IS AVAILABLEFOR USE
3、BY ALLDEPARTMENTSAPPROVED BYMonica L. PoelkingAND AGENCIES OF THEDEPARTMENT OF DEFENSEDRAWING APPROVAL DATE95-12-28MICROCIRCUIT, DIGITAL, RADIATIONHARDENED ADVANCED CMOS, 9-BIT ODD/EVENPARITY GENERATOR CHECKER, TTLCOMPATIBLE INPUTS, MONOLITHIC SILICONAMSC N/AREVISION LEVELCSIZEACAGE CODE672685962-96
4、720SHEET1 OF 22DSCC FORM 2233APR 97 5962-E407-00DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA5962-96720DEFENSE SUPPLY CENTER COLUMBUS
5、COLUMBUS, OHIO 43216-5000REVISION LEVELCSHEET2DSCC FORM 2234APR 971. SCOPE1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) andspace application (device class V). A choice of case outlines and lead finishes are available and
6、are reflected in the Part or IdentifyingNumber (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN.1.2 PIN. The PIN is as shown in the following example:5962 F 96720 01 V X CG0DG0D G0DG0D G0DG0DG0DG0D G0DG0D G0DG0DG0DG0D G0D G0D G0D G0DFederal RHA De
7、vice Device Case Lead stock class designator type class outline finishdesignator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3)/ Drawing number1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are markedwith the
8、appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levelsand are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.1.2.2 Device type(s). The device type(s) identify the circuit function as follows:Device type
9、 Generic number Circuit function01 ACTS280 Radiation hardened SOS, advanced CMOS,odd/even parity generator checker,TTL compatible02 ACTS280-02 1/ Radiation hardened SOS, advanced CMOS,odd/even parity generator checker,TTL compatible1.2.3 Device class designator. The device class designator is a sing
10、le letter identifying the product assurance level as follows:Device class Device requirements documentationM Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JANclass level B microcircuits in accordance with MIL-PRF-38535, appendix AQ or V Certification and qualification
11、to MIL-PRF-385351.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:Outline letter Descriptive designator Terminals Package styleC CDIP2-T14 14 dual-in-line packageX CDFP3-F14 14 flat package1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 f
12、or device classes Q and V or MIL-PRF-38535,appendix A for device class M.1/ Device type -02 is the same as device type -01 except that the device type -02 products are manufactured at an overseas waferfoundry. Device type -02 is used to positively identify, by marketing part number and by brand of t
13、he actual device, material that issupplied by an overseas foundry.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA5962-96720DEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000REVISION LEVELCSHEET3DSCC FORM 2234APR
14、 971.3 Absolute maximum ratings. 1/ 2/ 3/Supply voltage range (VCC) . -0.5 V dc to +7.0 V dcDC input voltage range (VIN). -0.5 V dc to VCC+ 0.5 V dcDC output voltage range (VOUT) -0.5 V dc to VCC+ 0.5 V dcDC input current, any one input (IIN) . 10 mADC output current, any one output (IOUT) 50 mAStor
15、age temperature range (TSTG) -65C to +150CLead temperature (soldering, 10 seconds). +265CThermal resistance, junction-to-case (JC):Case outline C. 24C/WCase outline X. 30C/WThermal resistance, junction-to-ambient (JA):Case outline C. 74C/WCase outline X. 116C/WJunction temperature (TJ) . +175CMaximu
16、m package power dissipation at TA= +125C (PD): 4/Case outline C. 0.68 WCase outline X. 0.43 W1.4 Recommended operating conditions. 2/ 3/Supply voltage range (VCC) . +4.5 V dc to +5.5 V dcInput voltage range (VIN) . +0.0 V dc to VCCOutput voltage range (VOUT) +0.0 V dc to VCCMaximum low level input v
17、oltage (VIL) 0.8 VMinimum high level input voltage (VIH) . VCC/2Case operating temperature range (TC) . -55C to +125CMaximum input rise and fall time at VCC= 4.5 V (tr, tf) 10 ns/VRadiation features:Total dose 3 x 105Rads (Si)Single event phenomenon (SEP) effectivelinear energy threshold (LET) no up
18、sets (see 4.4.4.4). 100 MeV/(cm2/mg) 5/Dose rate upset (20 ns pulse). 1 x 1011Rads (Si)/s 5/Latch-up. None 5/Dose rate survivability. 1 x 1012Rads (Si)/s 5/2. APPLICABLE DOCUMENTS2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
19、 of thisdrawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of theDepartment of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation.SPECIFICATIONDEPARTMENT OF DEFENSEMIL-P
20、RF-38535 - Integrated Circuits, Manufacturing, General Specification for.1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximumlevels may degrade performance and affect reliability.2/ Unless otherwise specified, all voltages are refe
21、renced to GND.3/ The limits for the parameters specified herein shall apply over the full specified VCCrange and case temperature range of -55C to+125C unless otherwise noted.4/ If device power exceeds package dissipation capability, provide heat sinking or derate linearly (the derating isbased on J
22、A) at the following rate:Case C . 13.5 mW/CCase X 8.6 mW/C5/ Guaranteed by design or process but not tested.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA5962-96720DEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-
23、5000REVISION LEVELCSHEET4DSCC FORM 2234APR 97STANDARDSDEPARTMENT OF DEFENSEMIL-STD-883 - Test Method Standard Microcircuits.MIL-STD-973 - Configuration Management.MIL-STD-1835 - Interface Standard For Microcircuit Case Outlines.HANDBOOKSDEPARTMENT OF DEFENSEMIL-HDBK-103 - List of Standard Microcircu
24、it Drawings (SMDs).MIL-HDBK-780 - Standard Microcircuit Drawings.(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization DocumentOrder Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)2.2 Order of precedence. In the
25、 event of a conflict between the text of this drawing and the references cited herein, the text of thisdrawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemptionhas been obtained.3. REQUIREMENTS3.1 Item requirements. The indivi
26、dual item requirements for device classes Q and V shall be in accordance withMIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification inthe QM plan shall not affect the form, fit, or function as described herein. The individual i
27、tem requirements for device class M shall be inaccordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein.3.1.1 Microcircuit die. For the requirements for microcircuit die, see appendix A to this document.3.2 Design, construction, and physical dimensions. The
28、 design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein.3.2.2 Terminal connections. The termi
29、nal connections shall be as specified on figure 1.3.2.3 Truth table. The truth table shall be as specified on figure 2.3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3.3.2.5 Switching waveform and test circuit. The switching waveforms and test circuits shall be as specified o
30、n figure 4. 3.2.6 Radiation exposure circuit. The radiation test connections shall be as specified in table III herein.3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electricalperformance characteristics and postirradiation par
31、ameter limits are as specified in table I and shall apply over the full case operatingtemperature range.3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests foreach subgroup are defined in table I.3.5 Marking. The part
32、shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked aslisted in MIL-HDBK-103. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, themanufacturer has the option of not marking the “5962-“ on the device
33、. For RHA product using this option, the RHA designator shall stillbe marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be inaccordance with MIL-PRF-38535, appendix A.3.5.1 Certification/compliance mark. The certification mark for
34、device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A.3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed
35、manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of complianceshall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). Thecertificate of compliance submitte
36、d to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that themanufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, therequirements of MIL-PRF-38535, appendix A and herein.Provided by IHSNot
37、for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA5962-96720DEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000REVISION LEVELCSHEET5DSCC FORM 2234APR 973.7 Certificate of conformance. A certificate of conformance as required for devic
38、e classes Q and V inMIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to thisdrawing.3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein)involving dev
39、ices acquired to this drawing is required for any change as defined in MIL-STD-973.3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option toreview the manufacturers facility and applicable required documentation. Offshore d
40、ocumentation shall be made available onshore at theoption of the reviewer.3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit groupnumber 39 (see MIL-PRF-38535, appendix A).4. QUALITY ASSURANCE PROVISIONS4.1 Sampling and insp
41、ection. For device classes Q and V, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect theform, fit, or function as described herein. For device class M
42、, sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A.4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted on alldevices prior to qualification and technology conformance inspection. For device cla
43、ss M, screening shall be in accordance with method5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection.4.2.1 Additional criteria for device class M.a. Burn-in test, method 1015 of MIL-STD-883.(1) Test condition A, B, C or D. The test circuit shall be mai
44、ntained by the manufacturer under document revision level controland shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs,outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 10
45、15.(2) TA= +125C, minimum.b. Interim and final electrical test parameters shall be as specified in table IIA herein.4.2.2 Additional criteria for device classes Q and V.a. The burn-in test duration, test condition and test temperature, or approved alternatives shall be as specified in the devicemanu
46、facturers QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be maintained under documentrevision level control of the device manufacturers Technology Review Board (TRB) in accordance withMIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon requ
47、est. The test circuit shall specifythe inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1015 ofMIL-STD-883.b. Interim and final electrical test parameters shall be as specified in table IIA herein.c. Additional screening for device
48、 class V beyond the requirements of device class Q shall be as specified inMIL-PRF-38535, appendix B.4.3 Qualification inspection for device classes Q and V. Qualification inspection for device classes Q and V shall be in accordancewith MIL-PRF-38535. Inspections to be performed shall be those speci
49、fied in MIL-PRF-38535 and herein for groups A, B, C, D, and Einspections (see 4.4.1 through 4.4.4).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA5962-96720DEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000REVISION LEVELCSHEET6DSCC FORM 2234
