1、REVISIONSLTR DESCRIPTION DATE (YR-MO-DA) APPROVEDREV SHEETREVSHEETREV STATUSOF SHEETSREVSHET 123456789101PMIC N/APREPARED BY Gary Zahn DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 STANDARDMICROCIRCUITDRAWINGTHIS DRAWING IS AVAILABLEFOR USE BY ALLDEPARTMENTSAND AGENCIES OF THEDEPARTMENT O
2、F DEFENSEAMSC N/A CHECKED BYMichael C. JonesMICROCIRCUIT, HYBRID, LINEAR, 12-BIT, DIGITAL TO ANALOG CONVERTERAPPROVED BYKendall A. CottongimDRAWING APPROVAL DATE97-02-05SIZEACAGE CODE672685962-96794REVISION LEVELSHEET 1 OF 11DESC FORM 193JUL 94 5962-E084-97DISTRIBUTION STATEMENT A. Approved for publ
3、ic release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGDEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OH 43216-5000SIZEA5962-96794REVISION LEVEL SHEET2DESC FORM 193AJUL 941. SCOPE1.1 Scope. This dra
4、wing documents five product assurance classes, class D (lowest reliability), class E, (exceptions), class G(lowest high reliability), class H (high reliability), and class K, (highest reliability) and a choice of case outlines and lead finishes areavailable and are reflected in the Part or Identifyi
5、ng Number (PIN). When available, a choice of radiation hardness assurance levelsare reflected in the PIN.1.2 PIN. The PIN shall be as shown in the following example:5962 - 96794 01 H X A G0DG0D G0DG0D G0DG0DG0DG0D G0DG0D G0DG0DG0D G0D G0D G0D G0D G0D Federal RHA Device Device Case Leadstock class de
6、signator type class outline finishdesignator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3)/ Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. The RHA marked devices shall meet the MIL-PRF-38534 specified RHAlevels and shall be marked with the appropriate
7、RHA designator. A dash (-) indicates a non-RHA device.1.2.2 Device type(s). The device type(s) shall identify the circuit function as follows:Device type Generic number Circuit function01 MSK 1339B 12-bit, digital to analog converter1.2.3 Device class designator. This device class designator shall b
8、e a single letter identifying the product assurance level asfollows:Device class Device performance documentationD, E, G, H, or K Certification and qualification to MIL-PRF-385341.2.4 Case outline(s). The case outline(s) shall be as designated in MIL-STD-1835 and as follows:Outline letter Descriptiv
9、e designator Terminals Package styleX See figure 1 16 Dual-in-line1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534.1.3 Absolute maximum ratings. 1/Supply voltage (V ) . +7.0 V dcDDDigital supply voltage (V ) -0.5 V dc to +VDD DDAnalog voltages (V or (V ). -25 V dc to +25 V d
10、cREF RFBAnalog input current -10 mA to +10 mATotal power dissipation (P ) . 500 mWDJunction temperature (T ) . +150G28C JStorage temperature -65G28C to +150G28CLead temperature (soldering, 10 seconds) +300G28C1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Ext
11、ended operation at themaximum levels may degrade performance and affect reliability. All voltages are with respect to ground.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGDEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OH 43216-
12、5000SIZEA5962-96794REVISION LEVEL SHEET3DESC FORM 193AJUL 941.4 Recommended operating conditions.Supply voltage (V ) . +4.75 V dc to +5.25 V dcDDDigital input high voltage . 3 V minimumDigital input low voltage . 0.8 V maximumAmbient operating temperature range(T ) -55G28C to +125G28CA2. APPLICABLE
13、DOCUMENTS2.1 Government specification, standards, and handbook. The following specification, standards, and handbook form a part ofthis drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issueof the Department of Defense Index of
14、 Specifications and Standards (DoDISS) and supplement thereto, cited in the solitation.SPECIFICATIONDEPARTMENT OF DEFENSEMIL-PRF-38534 - Hybrid Microcircuits, General Specification for.STANDARDSDEPARTMENT OF DEFENSEMIL-STD-883 - Test Methods and Procedures for Microelectronics.MIL-STD-973 - Configur
15、ation Management.MIL-STD-1835 - Microcircuit Case Outlines.HANDBOOKDEPARTMENT OF DEFENSEMIL-HDBK-780 - Standard Microcircuit Drawings.(Unless otherwise indicated, copies of the specification, standards, and handbook are available from the StandardizationDocument Order Desk, 700 Robbins Avenue, Build
16、ing 4D, Philadelphia, PA 19111-5094.)2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text ofthis drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specificexemptio
17、n has been obtained.3. REQUIREMENTS3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be inaccordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or asdesignated in the device manufactur
18、ers Quality Management (QM) plan or as designated for the applicable device class. Therefore, the tests and inspections herein may not be performed for the applicable device class (see MIL-PRF-38534). Futhermore, the manufacturers may take exceptions or use alternate methods to the tests and inspect
19、ions herein and not performthem. However, the performance requirements as defined in MIL-PRF-38534 shall be met for the appilcable device class.3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified inMIL-PRF-38534 and herein.3.2.1
20、Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1.3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRA
21、WINGDEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OH 43216-5000SIZEA5962-96794REVISION LEVEL SHEET4DESC FORM 193AJUL 943.2.3 Truth table(s). The truth table(s) shall be as specified on figure 3.3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance charac
22、teristics are asspecified in table I and shall apply over the full specified operating temperature range.3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical testsfor each subgroup are defined in table I.3.5 Marking of Device
23、(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked withthe PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked as listed in QML-38534.3.6 Data. In addition to the general performance requirements of MIL-PRF-38534
24、, the manufacturer of the device describedherein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, foreach device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those
25、which, ifany, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be madeavailable to the preparing activity (DSCC-VA) upon request.3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to sup
26、ply to this drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturers product meets theperformance requirements of MIL-PRF-38534 and herein.3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provide
27、d with each lot ofmicrocircuits delivered to this drawing.4. QUALITY ASSURANCE PROVISIONS4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modifiedin the device manufacturers Quality Management (QM) plan. The modification in the QM plan s
28、hall not affect the form, fit, orfunction as described herein.4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply:a. Preseal burn-in test, method 1030 of MIL-STD-883. (optional for class H)(1) Test condition A, B, C, or D. The test circui
29、t shall be maintained by the manufacturer under document revision levelcontrol and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shallspecify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent sp
30、ecified in testmethod 1030 of MIL-STD-883.(2) T as specified in accordance with table I of method 1015 of MIL-STD-883.Ab. Burn-in test, method 1015 of MIL-STD-883.(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision levelcontrol and shall
31、 be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shallspecify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in testmethod 1015 of MIL-STD-883.(2) T as specified in accordance with table I
32、of method 1015 of MIL-STD-883.Ac. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter testsprior to burn-in are optional at the discretion of the manufacturer.Provided by IHSNot for ResaleNo reproduction or networking permitted w
33、ithout license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGDEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OH 43216-5000SIZEA5962-96794REVISION LEVEL SHEET5DESC FORM 193AJUL 94TABLE I. Electrical performance characteristics. G0DG0D G0D G0DG0D G0DTest G0D Symbol G0D Conditions 1/ G0D Group A G0D Device G0D Limi
34、ts G0D UnitG0DG0D -55G28C G06 T G06 +125G28C G0D subgroups G0D type G0D G0DCG0DG0D unless otherwise specified G0DG0DG0DG0DG0DG0DG0D G0DG0DG0D Min G0D Max G0DG0DG0D G0D G0DG0D G0D G0DG0DG0D G0D G0DG0D G0D G0DQuiescent current G0D I G0DDigital inputs = 0 V G0D 1,2,3 G0D 01 G0DG0D 2.5 G0D mAQG0DG0D G0D
35、 G0DG0D G0D G0DG0DG0D G0D G0DG0D G0D G0DAccuracy 2/ G0DINL G0DBest line, T = +25G28C G0D 1 G0D 01 G0D -1 G0D +1 G0D LSBAG0DG0D G0D G0DG0D G0D G0DG0DG0D G0D G0DG0D G0D G0DGain error G0D A G0DUse internal RFB at full G0D 1 G0D 01 G0D -2 G0D +2 G0D LSBEG0DG0Dscale output G0DG0DG0DG0DG0DG0DG0D G0D 2,3 G
36、0DG0D -3 G0D +3 G0DG0DG0D G0D G0DG0D G0D G0DGain error temperature G0D T G0DG8CGain/G8CTemp, T = -55G28C and G0D 2,3 G0D 01 G0D -5 G0D +5 G0DPPM/G28CCGE Acoefficient G0DG0D+125G28C G0DG0DG0DG0DG0DG0DG0D G0D G0DG0D G0D G0DOutput leakge 2/ G0D I G0Df = DC, T = +25G28C G0D 1 G0D 01 G0D -200 G0D +200 G0
37、D nAOL AG0DG0D G0D G0DG0D G0D G0DG0DG0D G0D G0DG0D G0D G0DReference input 2/ G0DV G0Df = DC, T = +25G28C G0D 1 G0D 01 G0D 5 G0D 20 G0D kohmREF Aresistance G0DG0D G0D G0DG0D G0D G0DG0DG0D G0D G0DG0D G0D G0DG0DG0D G0D G0DG0D G0D G0DInput leakage current G0DI G0DAll digital inputs, V = 0 V G0D 1,2,3 G0
38、D 01 G0D -1 G0D +1 G0D AIND INDG0DG0D G0D G0DG0D G0D G0DG0DG0D G0D G0DG0D G0D G0DInput capacitance 2/ G0DC G0DAll digital inputs, T = +25G28C G0D 4 G0D 01 G0DG0D 8 G0D pFIND AG0DG0D G0D G0DG0D G0D G0DG0DG0D G0D G0DG0D G0D G0DOutput capacitance 2/ G0DC G0DC 1; DAC 1 NP = 0s G0D 4 G0D 01 G0DG0D 100 G0
39、D pFOUT IOUTG0DG0DT = +25G28C G0DG0DG0DG0DG0DAG0DG0D G0DG0DG0DG0DG0DG0DG0D G0D G0DG0D G0D G0DG0DG0DC 2; DAC 1 NP = 0s G0DG0DG0DG0D 210 G0DIOUTG0DG0DT = +25G28C G0DG0DG0DG0DG0DAG0DG0D G0D G0DG0D G0D G0DG0DG0D G0D G0DG0D G0D G0DCurrent transition time G0DCTR G0DFull scale change measured G0D 4 G0D 01
40、G0DG0D 2 G0D s2/ G0DG0D10% to 90%, T = +25G28C G0DG0DG0DG0DG0DAG0DG0D G0D G0DG0D G0D G0D1/ V = +5 V dc and V = 10 V dc.DD REF2/ Parameter shall be guaranteed to the limits specified in table I for all lots not specifically tested.Provided by IHSNot for ResaleNo reproduction or networking permitted w
41、ithout license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGDEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OH 43216-5000SIZEA5962-96794REVISION LEVEL SHEET6DESC FORM 193AJUL 94Case outline X.G0DG0D G0D G0DG0D Symbol G0D Millimeters G0D Inches G0DG0D G0D G0DG0DG0D G0DG0DG0D Min G0D Max G0D Min G0D Max G0DG0D A
42、G0D 19.03 G0D 19.81 G0D 0.760 G0D 0.780 G0DG0D B G0D 3.18 G0DG0D 0.125 G0D G0DG0D C G0D 0.41 G0D 0.51 G0D 0.016 G0D 0.020 G0DG0D D G0D 17.78 REF G0D 0.700 REF G0DG0D E G0D 2.21 G0D 2.72 G0D 0.087 G0D 0.107 G0DG0D F G0D 0.38 G0D 0.89 G0D 0.015 G0D 0.035 G0DG0D G G0D 7.11 G0D 7.62 G0D 0.280 G0D 0.300
43、G0DG0D H G0D 0.23 G0D 0.30 G0D 0.009 G0D 0.012 G0DG0D I G0D 7.62 BSC G0D 0.300 REF G0DG0D J G0D 0.76 G0D 1.02 G0D 0.030 G0D 0.040 G0DNOTES:1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units ofmeasurement. In case of problems involving conflict
44、s between the metric and inch-pound units, the inch-pound unitsshall rule.2. Pin numbers are for reference only.FIGURE 1. Case outline.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGDEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS,
45、 OH 43216-5000SIZEA5962-96794REVISION LEVEL SHEET7DESC FORM 193AJUL 94G0DG0D G0DG0D Case outline G0D X G0DG0DG0D G0DG0DG0D G0DG0D Device type G0D 01 G0DG0DG0D G0DG0DG0D G0DG0D Terminal number G0D Terminal symbol G0DG0DG0D G0DG0DG0D G0DG0D 1 G0D Output 1 G0DG0DG0D G0DG0D 2 G0D Output 2 G0DG0DG0D G0DG
46、0D 3 G0D Analog ground G0DG0DG0D G0DG0D 4 G0D D 3 (MSB) G0DG0DG0D G0DG0D 5 G0D D 2 G0DG0DG0D G0DG0D 6 G0D D 1 G0DG0DG0D G0DG0D 7 G0D D 0 (LSB) G0DG0DG0D G0DG0D 8 G0D Chip select G0DG0DG0D G0DG0D 9 G0D Write/read G0DG0DG0D G0DG0D 10 G0D A 0 G0DG0DG0D G0DG0D 11 G0D A 1 G0DG0DG0D G0DG0D 12 G0D Digital
47、ground G0DG0DG0D G0DG0D 13 G0D CLR G0DG0DG0D G0DG0D 14 G0D V G0DDDG0DG0D G0DG0D 15 G0D V G0DREFG0DG0D G0DG0D 16 G0D Feedback resistor G0DG0DG0D G0DFIGURE 2. Terminal connections.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRA
48、WINGDEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OH 43216-5000SIZEA5962-96794REVISION LEVEL SHEET8DESC FORM 193AJUL 94Control inputsOperationA1 A0CSWRCLRX X X X 0 Resets DAC 12-bit register to code 0000 0000 0000X X 1 1 1 No operation; device not selected0 0 LOW to HIGH 0 1 Load LOW byte data register onedges a
