1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Interchange device type 01 with 03. 97-12-17 K. A. Cottongim B Paragraph 1.3, thermal resistance, junction-to-case, case outline Z, change 12C/W to 15C/W. Figure 1, case outline U, correct dimension A minimum from .255“ to .200“. Correct notes on
2、 figure 1. Update drawing boilerplate. 02-08-30 Raymond Monnin C Add device type 04. 05-11-08 Raymond Monnin REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Gary Zahn DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWI
3、NG CHECKED BY Michael C. Jones POST OFFICE BOX 3990 COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Kendall A. Cottongim MICROCIRCUIT, LINEAR, OPERATIONAL AMPLIFIER, SINGLE, HIGH VOLTAGE, MOSFET, MONOLITHIC SILICON AND AGENCIES OF THE
4、 DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 97-01-13 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-96897 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E069-06Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 596
5、2-96897 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available a
6、nd are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 96897 01 H X C Federal RHA Device Device Case Lead stock class designator type class
7、 outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A da
8、sh (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 MSK 164B, MSK 167B High voltage, MOSFET operational amplifier 02 MSK 162B, MSK 163B High voltage, MOSFET operational amplifier 03 MSK 1
9、58B, MSK 159B High voltage, MOSFET operational amplifier 04 MSK 167H High voltage, MOSFET operational amplifier 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 an
10、d require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard
11、military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature r
12、ange, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These
13、 exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal
14、, QML certified flow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96897 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3
15、 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style U See figure 1 8 Dual-in-line (Z tab power) X See figure 1 24 Quad ceramic flat pack Y See figure 1 8 Dual-in-line (power)
16、 Z See figure 1 14 Dual-in-line (end tab) 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Supply voltage ( total VCC). 350 V dc 2/ Common mode input voltage range. VCCDifferential input voltage 16 V dc Output current (within SOA continuous)
17、 60 mA Lead temperature (soldering, 10 seconds) +300C Junction temperature (TJ) +150C Thermal resistance, junction-to-case (JC); Case outlines U and Y 10C/W Case outlines X and Z 15C/W Storage temperature range . -55C to +150C Case operating temperature range (TC) -55C to +125C 1.4 Recommended opera
18、ting conditions. 3/ Supply voltage (VCC) 50 V dc to 170 V dc Offset pot (device type 01, only) 200 kohm to -VCCCurrent limit equation ILIM= 3 / RCLOutput snubber network 100 ohms / 330 pF Ambient operating temperature range (TA) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, sta
19、ndards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybr
20、id Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780
21、 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the ev
22、ent of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1/ Stresses above the absolute maximum ratings m
23、ay cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Derate 0.5 V/0C below +250C. 3/ RC network for compensation (AV= 10 V/V) equals 2 kohm / 18 pF applies to device types 01, 03, and 04. Device type 02 has internal comp
24、ensation. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96897 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. T
25、he individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the
26、 applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, o
27、r function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and fi
28、gure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temp
29、erature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be
30、 marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format)
31、from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the m
32、anufacturer and be made available to the preparing activity (DSCC-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm tha
33、t the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. Provided by IHSNot for ResaleNo reproducti
34、on or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96897 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits Test Symbol Conditions 1/ -55C TC +1
35、25C unless otherwise specified Group A subgroups Device type Min Max Unit 1 2 2 3 Quiescent current IQ VIN= 0 V 3 All 2.1 mA Input offset voltage VOSVIN= 0 V, AV= 10, TA= +25C 1 All 30 mV Input offset voltage drift 2/ VOS T VIN= 0 V, AV= 10, TA= -55C and +125C 2,3 All 65 V/C Input bias current 2/ II
36、BVCM= 0 V, TA= +25C 1 All 50 pA Input offset current 2/ IOSVCM= 0 V, TA= +25C 1 All 50 pA -VCC= -150 V, +VCC= +50 V to +150 V, TA= +25C 1 All 94 dB Power supply rejection ratio 2/ PSRR +VCC= +150 V, -VCC= -50 V to -150 V, TA= +25C 1 All 94 dB Common mode rejection ratio 2/ CMRR VCM= 90 V dc, TA= +25
37、C 4 All 84 dB Voltage gain 2/ AVf = 15 Hz, VOUT= 100 V, TA= +25C 4 All 94 dB Capacitive load drive 2/ CDR AV= 10 V/V, TA= +25C 4 All 10 nF Output voltage swing VPPf = 1 kHz, IOUT= 40 mA, TA= +25C 4 All 138 V Output current IOUTPeak, VOUT= maximum, TA= +25C 4 All 60 mA Slew rate SR VOUT= 50 V, AV= 10
38、, CC= open, TA= +25C 4 All 20 V/s 1/ VCC= 150 V, unless otherwise specified. 2/ Parameter shall be guaranteed to the limits specified in table I for all lots not specifically tested. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCU
39、IT DRAWING SIZE A 5962-96897 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 Case outline U. Millimeters Inches Symbol Min Max Min MaxA 5.08 6.73 .200 .265 A1 3.68 3.94 .145 .155 b 0.71 0.81 .028 .032 D 26.29 26.54 1.035 1.045 D1 19.93 20.19 .7
40、85 .795 D2 13.59 13.84 .535 .545 D3 3.05 3.30 .120 .130 E 13.59 13.84 .535 .545 E1 7.24 7.49 .285 .295 E2 3.05 3.30 .120 .130 e 1.41 2.67 .095 .105 e1 7.49 7.75 .295 .305 eA 22.73 22.99 .895 .905 I 3.05 3.30 .120 .130 L 4.57 10.67 .180 .420 NOTE: 1. The U.S. government preferred system of measuremen
41、t is the metric SI system. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Leads in true position within 0.01 inch (0.25 mm) R at MMC at seating plane. FIGURE 1. Case ou
42、tline(s). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96897 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Millimeters Inches Symbo
43、l Min Max Min MaxA 1.70 3.23 .067 .127 b 0.33 0.43 .013 .017 C 0.10 0.18 .004 .007 D/E 9.40 10.92 .370 .430 E1 6.10 6.60 .240 .260 l 7.62 .300 S1 1.65 2.16 .065 .085 NOTE: 1. The U.S. government preferred system of measurement is the metric SI system. This item was designed using inch-pound units of
44、 measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. FIGURE 1. Case outline(s) - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE
45、A 5962-96897 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Case outline Y. Millimeters Inches Symbol Min Max Min MaxA 13.59 13.84 .535 .545 B 13.59 13.84 .535 .545 C 5.08 6.60 .200 .260 D 0.71 0.81 .028 .032 E 1.41 2.67 .095 .105 F 7.49 7.75
46、.295 .305 G 3.68 3.94 .145 .155 K 4.57 10.67 .180 .420 L 22.48 23.24 .885 .915 R 1.02 .040 NOTE: 1. The U.S. government preferred system of measurement is the metric SI system. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric an
47、d inch-pound units, the inch-pound units shall rule. 2. Leads in true position within 0.01 inch (0.25 mm) R at MMC at seating plane. FIGURE 1. Case outline(s) - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING
48、SIZE A 5962-96897 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 Case outline Z. Millimeters Inches Symbol Min Max Min MaxA 5.59 .220 b 0.41 0.51 .016 .020 D 29.72 30.23 1.170 1.190 D1 20.07 20.57 .790 .810 e 2.54 TYP. .100 TYP. E 13.97 14.49 .550 .570 eA 7.37 7.87 .290 .310 F 1.40 1.65 .055 .065 L 12.70 .500 P 2.24 2.49 .088 .09
