1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Paragraph 1.3 corrected the Output current (IOUT) from 2.0 A to 3.0 A. Updated drawing to reflect current requirements. -sld 02-08-27 Raymond Monnin B Update drawing. -gz 07-01-09 Joseph Rodenbeck C Updated drawing paragraphs. -sld 12-05-15 Charl
2、es F. Saffle REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Gary Zahn DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Michael C. Jones THIS DRAWING IS AVAILAB
3、LE FOR USE BY ALL DEPARTMENTS APPROVED BY Kendall A. Cottongim MICROCIRCUIT, LINEAR, VOLTAGE REGULATOR, POSITIVE, ADJUSTABLE, LOW DROPOUT, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 99-07-06 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-98649 SHEET 1 O
4、F 10 DSCC FORM 2233 APR 97 5962-E172-12Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98649 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope.
5、This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflec
6、ted in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 98649 01 H T X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation
7、 hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Ge
8、neric number 1/ Circuit function 01 SDP1085 3.0 A, positive voltage regulator, adjustable, low dropout 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require
9、 QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military
10、quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, man
11、ufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception
12、(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML cert
13、ified flow. This product may have a limited temperature range. 1/ The SDP1085 is similar to the LT1085 and OM1850 listed on Standard Microcircuit Drawing 5962-88646.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A
14、5962-98649 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style N See figure 1 3 Z-tab with nonisolated
15、 tab, (TO-257Z), with glass seal T See figure 1 3 Flange mount with nonisolated tab, (TO-257), with glass seal U See figure 1 3 Flange mount with isolated tab, (TO-257), with glass seal Z See figure 1 3 Z-tab with isolated tab, (TO-257Z), with glass seal 1.2.5 Lead finish. The lead finish shall be a
16、s specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Input to output voltage differential 35 V dc Output current (IOUT) . 3.0 A Storage temperature range -65 C to +150 C Lead temperature (soldering, 10 seconds) +300 C Junction temperature (TJ) +150 C Power dissipation (PD) . Internally lim
17、ited Thermal resistance junction-to-case (qJC): Case N and T . 3.5 C/W Case U and Z . 4.2 C/W Thermal resistance junction-to-ambient(qJA) 42 C/W 1.4 Recommended operating conditions. Input to output voltage differential 25 V dc Output current (IOUT) . 10 mA to 2.0 A Ambient operating temperature ran
18、ge (TA) -55 C to +125 C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the s
19、olicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. 1/ Stresses above
20、the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-
21、98649 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.
22、daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. N
23、othing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance w
24、ith MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance
25、 requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction,
26、 and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteris
27、tics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The el
28、ectrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition
29、 to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include
30、a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A
31、 certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Ce
32、rtificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-
33、98649 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55 C TA +125 C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Reference voltage VREF(VIN- VOUT)
34、= 3.0 V, IOUT= 10 mA 1 01 1.238 1.262 V 1.5 V (VIN- VOUT) 25 V, 10 mA IOUT 2.0 A 1,2,3 1.220 1.270 Line regulation 1/ DVOUT DVIN1.5 V (VIN- VOUT) 15 V, IOUT= 10 mA 1 01 0.2 % 1.5 V (VIN- VOUT) 35 V, IOUT= 10 mA 2,3 0.5 Load regulation 1/ DVOUT DIOUT(VIN- VOUT) = 3.0 V, 10 mA IOUT 2.0 A 1 01 0.8 % 2,
35、3 1.0 Dropout voltage VDOIOUT= 2.0 A, DVREF= 1.0% 1,2,3 01 1.5 V Thermal regulation - - - 30 ms pulse, TA= +25 C 1 01 0.02 %/W Ripple rejection DVIN DVOUTf = 120 Hz, CADJ= 25 mF, COUT= 25 mF (tantalum), IOUT= 2.0 A, (VIN- VOUT) = 3.0 V 4,5,6 01 60 dB Adjust pin current IADJ1.5 V (VIN- VOUT) 25 V, 10
36、 mA IOUT 2.0 A 1,2,3 01 120 mA Adjust pin current change DIADJ1.5 V (VIN- VOUT) 25 V, 10 mA IOUT 2.0 A, TA= +25 C 1 01 5.0 mA Minimum load current IMIN(VIN- VOUT) = 25 V 1,2,3 01 10 mA Current limit ILIM(VIN- VOUT) = 5 V 1,2,3 01 3.2 A (VIN- VOUT) = 25 V 0.2 Temperature stability 2/ DVOUT-55 C TJ +1
37、25 C 1,2,3 01 1.5 % Long term stability 2/ DVOUTt =1000 hrs, TA= +125 C 2 01 1.0 % 1/ Line and load regulation are measured at a constant junction temperature using a low duty cycle pulse technique. Although power dissipation is internally limited, regulation is guaranteed up to the maximum power di
38、ssipation of 30 W. Power dissipation is determined by the input/output differential voltage and the output current. Guaranteed maximum power dissipation will not be available over the full input/output voltage range. 2/ If not tested, shall be guaranteed to the limits specified in table I. Provided
39、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98649 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 Case outlines T and U. Symbol Millimeters Inches Min Max Min Max A 4
40、.83 5.08 .190 .200 A1 0.89 1.14 .035 .045 A2 3.05 BSC .120 BSC b 0.64 1.02 .025 .040 D 16.38 16.89 .645 .665 D1 10.41 10.92 .410 .430 D3 0.00 0.97 .000 .038 e 2.54 BSC .100 BSC E 10.41 10.67 .410 .420 L 12.70 19.05 .500 .750 O 13.39 13.64 .527 .537 P 3.56 3.81 .140 .150 NOTE: The U.S. government pre
41、ferred system of measurement is the metric SI system. However, this item was originally designed using inch-pound units of measurement. In the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. FIGURE 1. Case outline(s). Provided by IHSNot for Resa
42、leNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98649 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Case outlines N and Z. Symbol Millimeters Inches Min Max Min Max A 23.11 23.37 .910 .9
43、20 A1 10.41 10.67 .410 .420 A2 6.22 6.48 .245 .255 A3 3.05 3.30 .120 .130 b 0.71 0.81 .028 .032 D 4.70 5.59 .135 .220 D1 2.92 3.18 .115 .125 D2 0.89 1.14 .035 .045 e 2.54 BSC .100 BSC L 10.41 10.67 .410 .420 L1 12.70 19.05 .500 .750 L2 6.22 6.48 .245 .255 L3 3.05 3.30 .120 .130 P 3.05 3.30 .120 .130
44、 NOTE: The U.S. government preferred system of measurement is the metric SI system. However, this item was originally designed using inch-pound units of measurement. In the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. FIGURE 1. Case outline(s
45、) - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98649 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case outlines N and T (noniso
46、lated tab) U and Z (isolated tab) Terminal number Terminal symbol Terminal symbol 1 2 3 Tab Adjust No connection Input Output Adjust Output Input No connection FIGURE 2. Terminal connections.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MI
47、CROCIRCUIT DRAWING SIZE A 5962-98649 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements Subgroups (in accordance with MIL-PRF-38534, group A test table) Interim electrical parameters 1
48、 Final electrical parameters 1*, 2, 3, 4, 5, 6 Group A test requirements 1, 2, 3, 4, 5, 6 Group C end-point electrical parameters 1, 2, 3 End-point electrical parameters for Radiation Hardness Assurance (RHA) devices Not applicable * PDA applies to subgroup 1. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified
