DS EN ISO 4524-3-1995 Metallic coatings - Test methods for electrodeposited gold and gold alloy coatings - Part 3 Electrographic tests for porosity《金属覆盖层 电沉积金和贵金属合金覆盖层 第3部分：电图像孔隙率试.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

AGMA 96FTM5-1996 Differential Crowning A New Weapon Against Gear Noise and Dynamic Load《差分鼓形修整 一件对抗齿动噪声和动态载荷的新武器》.pdf

AGMA 96FTM6-1996 F-22 AMAD Gear Drive - Optimization of Resonance Characteristics by Detuning Coulomb Damping & Damped Force Response Analyses《F-22 AMAD齿轮传动装置.通过去谐 库仓阻尼和阻尼力响应分析对共振特.pdf

AGMA 96FTM7-1996 Dynamic Distribution of Load and Stress on External Involute Gearings《渐开线外啮合上载荷和应力的动态分布》.pdf

AGMA 96FTM8-1996 Thermal Rating of Gear Drives Balance Between Power Loss and Heat Dissipation《齿轮传动装置的热定额.功率损耗和热散逸之间的平衡》.pdf

AGMA 96FTM9-1996 Development of a Practical Thermal Rating Method for Enclosed Gear Drives《封闭传动装置的实际热定额方法的开发》.pdf

AGMA 97FTM1-1997 Calibration of Gear Measuring Instruments and Their Application to the Inspection of Product Gears《齿轮测量器具的校准及其在齿轮产品检验上的应用》.pdf

AGMA 97FTM10-1997 UltraSafe Gear Systems for Critical Applications - Initial Development《特殊用途用超安全齿轮系统.初步制定》.pdf

AGMA 97FTM11-1997 Non - Dimensional Characterization of Gear Geometry Mesh Loss and Windage《齿轮几何 啮合损失和偏差的无因次特性》.pdf

AGMA 97FTM12-1997 Introduction of a Jobbing System for Bevel and Hypoid Gears《伞形和准双曲面齿轮用作业系统的介绍》.pdf