1、 EIA STANDARD TP-16A Stripping Force Test (Solderless Wrapped Connectors) Test Procedure for Electrical ConnectorsEIA-364-16A (Revision of EIA-364-16) April 2002 ANSI/EIA-364-16A-2002(R2015) Approved: April 22, 2002 Reaffirmed: March 23, 2015 EIA-364-16A NOTICE EIA Engineering Standards and Publicat
2、ions are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need
3、. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their voluntary use by those
4、other than ECIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, ECIA does not assume any liability to any patent owner
5、, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This standard is based upon the major technical content of International Electrotechnical Commission standard 512-8, test 16k, stripping force, solderless wrapped connections, 1993-01, third edition. It con
6、forms in all essential respects to this IEC standard. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to det
7、ermine the applicability of regulatory limitations before its use. (From Standards Proposal No. 4893 formulated under the cognizance of the CE-2.0 Committee on EIA National Connector and Socket Standards, and reaffirmed per Standards Proposal No. 5345.05). Published by Electronic Components Industry
8、 Association 2015 Standards see figure 1. 4 Test procedure 4.1 The test fork shall be moved parallel to the post axis, toward the free end of the post at a rate of 25.4 millimeters to 50.8 millimeters (1 inch to 2 inches) per minute. 4.2 The force exerted on the wrapped connection by the test fork a
9、s it moves shall be measured. 4.3 The maximum force which is required to move the whole wrapped connection along the post a distance equivalent to one wire diameter shall be measured as the stripping force. 5 Details to be specified The following details shall be specified in the referencing documen
10、t: 5.1 Number of specimens to be tested 5.2 Selection method for specimens 5.3 Special conditions or requirements differing from those above 6 Test documentation Documentation shall contain the details specified in clause 5, with any exceptions, and the following: 6.1 Title of test 6.2 Specimen desc
11、ription including wire size and number of wraps 6.3 Test equipment used, and date of last and next calibration 6.4 Test and procedure 6.5 Values and observations 6.5.1 Rate of movement of test fork 6.5.2 Measured value of stripping force 6.5 3 Other data required by the referencing document 6.6 Name
12、 of operator and date of test EIA-364-16A Page 3 Figure 1 Stripping force test fixture Strip force Post Fixed mount Fork tinesSolderless wrapped connection Free end of post Stripping tool Fork ECIA Document Improvement Proposal If in the review or use of this document, a potential change is made evi
13、dent for safety, health or technical reasons, please fill in the appropriate information below and mail or FAX to: Electronic Components Industry Association EIA Standards & Technology Department 2214 Rock Hill Rd., Suite 265 Herndon, VA 20170 FAX: (571-323-0245) Document No.: Document Title: Submit
14、ters Name: Telephone No.: FAX No.: e-mail: Address: Urgency of Change: Immediate: At next revision: Problem Area: a. Clause Number and /or Drawing: b. Recommended Changes: c. Reason/Rationale for Recommendation: Additional Remarks: Signature: Date: FOR ECIA USE ONLY Responsible Committee: Chairman: Date comments forwarded to Committee Chairman: Electronic Components Industry Association 2214 Rock Hill Road, Suite 265 * Herndon, VA 20170 * tel 571-323-0294 * fax 571-323-0245 www.ecianow.org
