1、 EIA STANDARD Fixed Capacitors for Use in Electronic Equipment Part 17: Sectional Specification Fixed Metallized Polypropylene Film Dielectric a.c. and Pulse CapacitorsEIA-60384-17 (IEC 60384-17:2005, IDT) October 2014 ANSI/EIA-60384-17-2014 Approved: October 10, 2014 EIA-60384-17 NOTICE EIA Enginee
2、ring Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper prod
3、uct for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude th
4、eir voluntary use by those other than ECIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, ECIA does not assume any li
5、ability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This EIA Standard is identical (IDT) with the International Standard IEC Publication 60384-17:2005: Fixed Capacitors for Use in Electronic Equipment Part 17: Sectional Specificati
6、on . Fixed Metallized Polypropylene Film Dielectric a.c. and Pulse Capacitors. This document is the EIA Standard EIA-60384-17 2014 Edition 2: Fixed Capacitors for Use in Electronic Equipment Part 17: Sectional Specification Fixed Metallized Polypropylene Film Dielectric a.c. and Pulse Capacitors. Th
7、e text, figures and tables of IEC 60384-17:2005 are used in this Standard with the consent of the IEC and the American National Standards Institute (ANSI). These materials are subject to copyright claims of IEC and ECIA. No part of this publication may be reproduced in any form, including an electro
8、nic retrieval system, without the prior written permission of ECIA. All requests pertaining to EIA-60384-17 2014 Edition 2: Fixed Capacitors for Use in Electronic Equipment Part 17: Sectional Specification Fixed Metallized Polypropylene Film Dielectric a.c. and Pulse Capacitors should be submitted t
9、o ECIA at the address below. The IEC copyrighted material has been reproduced with permission from ANSI. The IEC Foreword and Introduction are not part of the requirements of this standard but are included for information purposes only. This Standard does not purport to address all safety problems a
10、ssociated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 5276, formulated unde
11、r the cognizance of the P-2.2 Committee on EIA Paper, Film, Mica any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC co
12、llaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinio
13、n on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ens
14、ure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently t
15、o the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered
16、responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its te
17、chnical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other I
18、EC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the sub
19、ject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60384-17 has been prepared by IEC technical committee 40: Capacitors and resistors for electronic equipment. This second edition cancels and replaces the first edition p
20、ublished in 1987 and constitutes minor revisions related to tables, figures and references. The text of this standard is based on the following documents: FDIS Report on voting40/1597/FDIS 40/1630/RVD Full information on the voting for the approval of this standard can be found in the report on voti
21、ng indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. EIA-60384-17 Page 2 IEC 60384 consists of the following parts, under the (new) general title Fixed capacitors for use in electronic equipment: Part 1: Generic specification Part 2: S
22、ectional specification: Fixed metallized polyethylene-terephthalate film dielectric d.c. capacitors Part 3: Sectional specification: Fixed tantalum chip capacitors Part 4: Sectional specification: Aluminium electrolytic capacitors with solid and non-solid electrolyte Part 5: Sectional specification:
23、 Fixed mica dielectric d.c. capacitors with a rated voltage not exceeding 3000 V Selection of methods of test and general requirements Part 6: Sectional specification: Fixed metallized polycarbonate film dielectric d.c. capacitors Part 7: Sectional specification: Fixed polystyrene film dielectric me
24、tal foil d.c. capacitors Part 8: Sectional specification: Fixed capacitors of ceramic dielectric, Class 1 Part 9: Sectional specification: Fixed capacitors of ceramic dielectric, Class 2 Part 11: Sectional specification: Fixed polyethylene-terephthalate film dielectric metal foil d.c. capacitors Par
25、t 12: Sectional specification: Fixed polycarbonate film dielectric metal foil d.c. capacitors Part 13: Sectional specification: Fixed polypropylene film dielectric metal foil d.c. capacitors Part 14: Sectional specification: Fixed capacitors for electromagnetic interference suppression and connectio
26、n to the supply mains Part 15: Sectional specification: Fixed tantalum capacitors with non-solid or solid electrolyte Part 16: Sectional specification: Fixed metallized polypropylene film dielectric d.c. capacitors Part 17: Sectional specification: Fixed metallized polypropylene film dielectric a.c.
27、 and pulse capacitors Part 18: Sectional specification: Fixed aluminium electrolytic chip capacitors with solid and non-solid electrolyte Part 19: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric chip d.c. capacitors Part 20: Sectional specification: Fixed metalli
28、zed polyphenylene sulfide film dielectric chip d.c. capacitors Part 21: Sectional specification: Fixed surface mount multilayer capacitors of ceramic dielectric, Class 1 Part 22: Sectional specification: Fixed surface mount multilayer capacitors of ceramic dielectric, Class 2 Part 23: Sectional spec
29、ification: Fixed surface mount metallized polyethylene naphthalate film dielectric d.c. capacitors Part 24: Sectional specification Surface mount fixed tantalum electrolytic capacitors with conductive polymer solid electrolyte (under consideration) Part 25: Sectional specification Surface mount fixe
30、d aluminium electrolytic capacitors with conductive polymer solid electrolyte (under consideration) All sectional specifications mentioned above do have one or more blank detail specifications being a supplementary document, containing requirements for style, layout and minimum content of detail spe
31、cifications. EIA-60384-17 Page 3 The QC 301300 number that appears on the front cover of this publication is the specification number in the IECQ Quality Assessment System for Electronic Components. The committee has decided that the contents of this publication will remain unchanged until the maint
32、enance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later da
33、te. EIA-60384-17 Page 4 FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 17: Sectional specification: Fixed metallized polypropylene film dielectric a.c. and pulse capacitors 1 General 1.1 Scope This part of IEC 60384 applies to fixed capacitors with metallized electrodes and poly-propylene die
34、lectric for use in electronic equipment. NOTE Capacitors which have mixed foil and metallized electrodes are also within the scope of this standard. These capacitors may have “self-healing“ properties depending on conditions of use. Capacitors covered by this specification are mainly intended for us
35、e with alternating voltage and/or for pulse applications. The maximum reactive power applicable is 10 000 var and the maximum peak voltage is 3 000 V. Capacitors for reactive power exceeding 500 var and to which a maximum peak voltage of 2 500 V at 50 Hz can be applied are not covered by this standa
36、rd, except when they are the highest part of a range of reactive power mainly situated below 500 var at 50 Hz. This standard is not intended to cover capacitance values higher than 20 F. Two performance grades of capacitors are covered, Grade 1 for long-life application and Grade 2 for general appli
37、cation. Capacitors for electromagnetic interference suppression are not included, but are covered by IEC 60384-14. Capacitors for electrical shock hazard protection (covered by IEC 60065) and fluorescent lamp and motor capacitors (covered by IEC technical committee 33, and IEC technical committee 34
38、) are also excluded. 1.2 Object The object of this standard is to prescribe preferred ratings and characteristics and to select from IEC 60384-1, the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of capacitor. Test s
39、everities and requirements prescribed in detail specifications referring to this sectional specification shall be of an equal or higher performance level, because lower performance levels are not permitted. 1.3 Normative references The following referenced documents are indispensable for the applica
40、tion of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60063:1963, Preferred number series for resistors and capacitors Amendment 1 (1967) Amendment 2 (1977) EIA-60384-
41、17 Page 5 IEC 60068-1, Environmental testing Part 1: General and guidance IEC 60384-1, Fixed capacitors for use in electronic equipment Part 1: Generic specification IEC 60384-17-1, Fixed capacitors for use in electronic equipment Part 17: Blank detail specification: Fixed metallized polypropylene f
42、ilm dielectric a.c. and pulse capacitors. Assessment level E IEC 60410, Sampling plans and procedures for inspection by attributes ISO 3, Preferred numbers Series of preferred numbers 1.4 Information to be given in a detail specification Detail specifications shall be derived from the relevant blank
43、 detail specification. Detail specifications shall not specify requirements inferior to those of the generic, sectional or blank detail specification. When more severe requirements are included, they shall be listed in 1.9 of the detail specification and indicated in the test schedules, for example
44、by an asterisk. NOTE The information given in 1.4.1 may for convenience, be presented in tabular form. The following information shall be given in each detail specification and the values quoted shall preferably be selected from those given in the appropriate clause of this sectional specification.
45、1.4.1 Outline drawing and dimensions There shall be an illustration of the capacitor as an aid to easy recognition and for comparison of the capacitor with others. Dimensions and their associated tolerances, which affect interchangeability and mounting, shall be given in the detail specification. Al
46、l dimensions shall preferably be stated in millimetres. Normally, the numerical values shall be given for the length of the body, the width and height of the body and the wire spacing, or for cylindrical types, the body diameter, and the length and diameter of the terminations. When necessary, for e
47、xample when a number of items (capacitance values/voltage ranges) are covered by a detail specification, the dimensions and their associated tolerances shall be placed in a table below the drawing. When the configuration is other than described above, the detail specification shall state such dimens
48、ional information as will adequately describe the capacitor. When the capacitor is not designed for use on printed boards, this shall be clearly stated in the detail specification 1.4.2 Mounting The detail specification shall specify the method of mounting to be applied for normal use and for the ap
49、plication of the vibration and the bump or shock tests. The capacitors shall be mounted by their normal means. The design of the capacitor may be such that special mounting fixtures are required in its use. In this case, the detail specification shall describe the mounting fixtures and they shall be used in the application of the vibration and bump or shock tests. 1.4.3 Ratings and characteristics The ratings and characteristics shall be in accordance with the relevant clauses of this specification, together with the following: EIA-60384-17 Page 6 1.4
