1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 10223-2:2012Steel wire and wire products for fencing and nettingPart 2: Hexagonal steel wire netting for agricultural, insulation and fencing purposesBS EN 10223-2:2012 BRI
2、TISH STANDARDNational forewordThis British Standard is the UK implementation of EN 10223-2:2012. It supersedes BS EN 10223-2:1998, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e I S E / 1 0 6 , W i r e R o d a n d W i r e .A list of or
3、ganizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited
4、 2012.ISBN 978 0 580 64499 3 ICS 77.140.65 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2012.Amendments issued since publicationDate T e x t a f f
5、 e c t e dBS EN 10223-2:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10223-2 November 2012 ICS 77.140.65 Supersedes EN 10223-2:1997English Version Steel wire and wire products for fencing and netting - Part 2: Hexagonal steel wire netting for agricultural, insulation and fencing purposes
6、 Fils et produits trfils en acier pour cltures et grillages - Partie 2: Grillage mailles hexagonales en acier utilis dans lagriculture pour lisolation et les cltures Stahldraht und Drahterzeugnisse fr Zune und Drahtgeflechte - Teil 2: Stahldrahtgeflecht mit sechseckigen Maschen fr landwirtschaftlich
7、e Zwecke, Isolierungen und Zune This European Standard was approved by CEN on 13 October 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-da
8、te lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
9、 under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, For
10、mer Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT
11、 EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10223-2:2012: EBS EN 10223-2:2012EN 10223-2:2012 (E) 2 Contents Page
12、 Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Information to be supplied by the purchaser .85 Manufacture 85.1 Base metal 85.2 Fabrication 86 Requirements .96.1 General 96.2 Netting, zinc or zinc alloy coated after fabrication .96.3 Netting made from zinc or zinc alloy coat
13、ed wire 96.4 Selvedges 127 Sampling and testing . 128 Inspection documentation . 129 Methods of test . 139.1 Netting, zinc or zinc alloy coated after fabrication 139.2 Netting made from zinc or zinc alloy coated wire . 139.3 Netting, organic coated after fabrication . 1310 Packaging 13BS EN 10223-2:
14、2012EN 10223-2:2012 (E) 3 Foreword This document (EN 10223-2:2012) has been prepared by Technical Committee ECISS/TC 106 “Wire rod and wires”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical tex
15、t or by endorsement, at the latest by May 2013, and conflicting national standards shall be withdrawn at the latest by May 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for
16、identifying any or all such patent rights. This document supersedes EN 10223-2:1997. EN 10223 “Steel wire and wire products for fencing and netting“ consists of the following parts: Part 1: Zinc and zinc-alloy coated steel barbed wire Part 2: Hexagonal steel wire netting for agricultural, insulation
17、 and fencing purposes Part 3: Hexagonal steel wire mesh products for engineering purposes Part 4: Steel wire welded mesh fencing Part 5: Steel wire woven hinged joint and knotted mesh fencing Part 6: Steel wire chain link fencing Part 7: Steel wire welded panels for fencing Part 8: Welded mesh gabio
18、n products According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
19、France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 10223-2:2012EN 10223-2:2012 (E) 4 1 Scope This European Standard speci
20、fies requirements for the dimensions and coating of steel wire netting having meshes of hexagonal shape specified for agricultural, insulation and fencing purposes. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable
21、for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10021, General technical delivery requirements for steel products EN 10204, Metallic products Types of inspection do
22、cuments EN 10244-1, Steel wire and wire products Non-ferrous metallic coatings on steel wire Part 1: General principles EN 10244-2:2009, Steel wire and wire products Non-ferrous metallic coatings on steel wire Part 2: Zinc or zinc alloy coatings EN 10245-1, Steel wire and wire products Organic coati
23、ngs on steel wire Part 1: General rules EN ISO 1461, Hot dip galvanized coatings on fabricated iron and steel articles Specifications and test methods (ISO 1461) EN ISO 16120-1, Non-alloy steel wire rod for conversion to wire Part 1: General requirements (ISO 16120-1) EN ISO 16120-2, Non-alloy steel
24、 wire rod for conversion to wire Part 2: Specific requirements for general-purpose wire rod (ISO 16120-2) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 mesh size of hexagonal mesh distance measured at right angles between two twisted sides.
25、 An average distance, D (see Figure 1) is measured over 10 meshes BS EN 10223-2:2012EN 10223-2:2012 (E) 5 Key D average mesh size Figure 1 Mesh size 3.2 hexagonal mesh hexagonal-netting consists of hexagonal shaped meshes, formed by twisting adjacent wires two by two, alternatively forming a twist t
26、o the right and to the left Note 1 to entry: The netting may have a border composed of one, two or more selvedge wires with a greater diameter than that used for the net. For widths above 50 cm or more stretching wires may be woven in the netting at equal distances (see Figure 2 and Table 1). BS EN
27、10223-2:2012EN 10223-2:2012 (E) 6 Key 1 selvedge 2 stretching wire Figure 2 Selvedge and stretching wires 3.3 twist tight helically winding of two wires around each other measured as each revolution of the two wires over 180 3.3.1 regular twist in the case of regular twist, the wires rotate only in
28、one direction; the minimum number of twists is three (see Figure 3 a) 3.3.2 reverse twist in the case of reverse twist the two wires are first twisted in one direction and then in the other direction. In the short transition zone the two wires are straightened parallel. The minimum number of twists
29、is 1,5 in each direction (see Figure 3 b) BS EN 10223-2:2012BS EN 10223-2:2012EN 10223-2:2012 (E) 7 a) Regular twist b) Reverse twist Figure 3 Twist BS EN 10223-2:2012EN 10223-2:2012 (E) 8 Table 1 Recommended minimum number of stretching wiresaRoll width rbmm Number of stretching wires rb 500 0 500
30、rb 1 000 1 1 000 rb 1 500 2 1 500 rb 2 000 3 aThese values apply to mesh sizes 25 mm and above. 4 Information to be supplied by the purchaser The following information shall be supplied by the purchaser at the time of enquiry and order: a) number of this European Standard; b) quantity; c) length of
31、rolls; d) mesh size; e) wire size; f) width; g) type - if no type is specified then either regular twist or reverse twist may be supplied; h) coating type; i) whether uniformity of coating is to be measured; j) inspection documentation requirements; k) agreed quality characteristics for testing (see
32、 Clause 7). 5 Manufacture 5.1 Base metal The base metal of the hexagonal netting shall be of good commercial quality steel selected from EN ISO 16120-1 and EN ISO 16120-2 and in a condition suitable for manufacture into netting. 5.2 Fabrication The netting may be coated after fabrication with either
33、 zinc or zinc alloy coating. In the case of zinc coating the purity of zinc shall be 98,5 % minimum (according to EN ISO 1461). Where an organic coating is specified it may be applied either on the uncoated netting or on the zinc or zinc alloy coated netting. BS EN 10223-2:2012EN 10223-2:2012 (E) 9
34、The netting may also be fabricated from zinc or zinc alloy coated wire with or without organic coating or with an extruded or sintered organic coating. Usual coating weight is according to EN 10244-2:2009, class A for Zn coating. Different coating weights may be agreed at time of order between purch
35、aser and supplier. 6 Requirements 6.1 General The netting shall be manufactured in the wire sizes, mesh sizes and widths as given in Table 2. The diameter of the wire characterizing the finished netting shall be the finished diameter in each case, either uncoated, zinc or zinc alloy coated or organi
36、c coated. Table 3 gives the relationship of the organic coated wire diameters to the core diameter. 6.2 Netting, zinc or zinc alloy coated after fabrication The netting shall meet the minimum values of coating mass and uniformity as stated in Table 2 and Table 4 of this European Standard. 6.3 Nettin
37、g made from zinc or zinc alloy coated wire Before fabricating into netting, the zinc or zinc alloy coated wire shall meet the minimum requirements of EN 10244-2:2009, class A for coating mass, adherence and where specified, the uniformity of the coating. Where samples are taken from the fabricated n
38、etting then the specified minimum coating mass requirement is reduced by 5 % and the specified dips by one half minute dip. For wire zinc or zinc alloy coated before fabrication, the twisted wire shall not break nor unwind in loading the netting up to 80 % of the breaking load of the wire (see Figur
39、e 4). NOTE Breaking load is the maximum force during the tensile test before breaking. BS EN 10223-2:2012EN 10223-2:2012 (E) 10 Key F 80 % of the braking load Figure 4 Loading of netting to test unwinding resistance BS EN 10223-2:2012EN 10223-2:2012 (E) 11 Table 2 Mesh sizes, preferred wire sizes, z
40、inc and zinc alloy coating masses and widths of netting Mesh details Preferred Wire diameter Minimum zinc or zinc alloy coating mass per m2meshfg/m2Typical roll widthsa dmm Size mm Tolerances mm Annealed mm Zinc coatedbmm Tolerancescmm 10 1,0 0,60 0,70 0,08 145 13 1,5 0,60 0,70 0,08 95 13 1,5 0,50 0
41、,60 0,08 80 16 2,0 0,60 0,70 0,08 70 20 2,0 0,60 0,70 0.,08 55 20 2,0 0,80 0,90 0,08 65 25 3,0 0,50 0,60 0,08 40 300 25 3,0 0,70 0,80 0,08 45 450 25 3,0 0,80 0,90 0,08 55 500 25 3,0 0,90 1,0 0,10 60 600 30 4,0 0,80 0,90 0,08 40 750 30 4,0 e0,90 1,0 0,10 40 900 30 4,0 e1,10 1,2 0,10 60 40 5,0 0,80 0,
42、90 0,08 35 40 5,0 0,90 1,0 0,10 45 1 000 40 5,0 1,1 1,2 0,10 55 1 200 50 6,0 0,80 0,90 0,08 25 1 500 50 6,0 0,90 1,0 0,10 30 1 800 50 6,0 1,1 1,2 0,10 40 2 000 65 7,0 0,90 1,0 0,10 30 75 8,0 0,90 1,0 0,10 20 75 8,0 1,1 1,2 0,10 25 75 8,0 1,3 1,4 0,10 30 100 8,0 1,5 1,6 0,10 30 a Other roll widths by
43、 agreement. b Zinc coated diameter in this table is the coated wire diameter in finished netting. c These tolerances apply to the diameter of the zinc coated wire in finished netting. d The tolerance on width shall be 1 mesh size measurement. e Tolerances on mesh size shall be 2,0 mm for rabbit nett
44、ing when specified. f Coating mass as netting coated after fabrication (see 9.1). For mesh width 75 mm and over, centre strands and selvedges should be by agreement. BS EN 10223-2:2012EN 10223-2:2012 (E) 12 Table 3 Relationship between the core diameter and the diameter of the organic coated wire aC
45、ore diameter Bright/Zinc coated wire mm Organic coated wire diameter mm Tolerance on organic coated wire mm 0,60 1,00 0,100,80 1,20 0,100,90 1,30 0,101,00 1,50 0,101,20 1,70 0,15aThe organic coated wire shall be free from burns, lumps and pinholes etc. 6.4 Selvedges If a single selvedge (see Figure
46、2) is used, the diameter of the selvedge wire shall be at least equal to or one size greater than that of the netting wire, e.g. netting wire of size 0,9 mm with a selvedge wire of size 1,0 mm. For netting having 2 ply or 3 ply selvedges and/or a centre stretching wire (see Figure 2), the wire for t
47、hese shall be at least equal to the netting wire diameter. Table 4 Wire size and number of dips to be withstood by zinc coated wires carried out in accordance with EN 10244-2:2009 Zinc coated diameter mm Number of dips Minute Half minute 0,7 - 2 0,80,9 1 0 1,01,2 1 1 1,41,6 1 1 7 Sampling and testin
48、g The manufacturer is responsible for the control of product quality by the application of statistical methods of sampling and analysis of results or, alternatively, by sampling and testing for the agreed quality characteristics at a rate of one roll in fifty. 8 Inspection documentation Non-specific
49、 testing and inspection documentation shall be provided according to EN 10021 and EN 10204. BS EN 10223-2:2012EN 10223-2:2012 (E) 13 9 Methods of test 9.1 Netting, zinc or zinc alloy coated after fabrication Zinc or zinc alloy coatings shall be tested in accordance with EN 10244-1 and EN 10244-2:2009 for coating mass and uniformity of coating , except that the coa
