EN 3294-2008 en Aerospace series - Bolts T-head close tolerance in heat resisting nickel base alloy NI-P101HT (Waspaloy) uncoated for increased height nuts -Classification 1 210 MP.pdf

上传人:刘芸 文档编号:710780 上传时间:2019-01-03 格式:PDF 页数:12 大小:422.43KB
下载 相关 举报
EN 3294-2008 en Aerospace series - Bolts T-head close tolerance in heat resisting nickel base alloy NI-P101HT (Waspaloy) uncoated for increased height nuts -Classification 1 210 MP.pdf_第1页
第1页 / 共12页
EN 3294-2008 en Aerospace series - Bolts T-head close tolerance in heat resisting nickel base alloy NI-P101HT (Waspaloy) uncoated for increased height nuts -Classification 1 210 MP.pdf_第2页
第2页 / 共12页
EN 3294-2008 en Aerospace series - Bolts T-head close tolerance in heat resisting nickel base alloy NI-P101HT (Waspaloy) uncoated for increased height nuts -Classification 1 210 MP.pdf_第3页
第3页 / 共12页
EN 3294-2008 en Aerospace series - Bolts T-head close tolerance in heat resisting nickel base alloy NI-P101HT (Waspaloy) uncoated for increased height nuts -Classification 1 210 MP.pdf_第4页
第4页 / 共12页
EN 3294-2008 en Aerospace series - Bolts T-head close tolerance in heat resisting nickel base alloy NI-P101HT (Waspaloy) uncoated for increased height nuts -Classification 1 210 MP.pdf_第5页
第5页 / 共12页
点击查看更多>>
资源描述

1、BRITISH STANDARDBS EN 3294:2008Aerospace series Bolts, T-head, close tolerance, in heat resisting nickel base alloy NI-P101HT (Waspaloy), uncoated for increased height nuts Classification: 1 210 MPa/730 CICS 49.030.20g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54

2、g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 3294:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2008 BSI 2008ISBN 978 0 580 60517 8National forewordT

3、his British Standard is the UK implementation of EN 3294:2008.The UK participation in its preparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can be obtained on request to its secretary.This publicat

4、ion does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate CommentsEUROPEAN STANDARD NORME EUROPENNE

5、EUROPISCHE NORM EN 3294 April 2008 ICS 49.030.20 English Version Aerospace series - Bolts, T-head, close tolerance, in heat resisting nickel base alloy NI-P101HT (Waspaloy), uncoated for increased height nuts -Classification: 1 210 MPa/730 C Srie arospatiale - Vis de prcision tte anti-rotation T en

6、alliage rsistant chaud base de nickel NI-P101HT (Waspaloy), non revtu pour crou renforc - Classification: 1 210 MPa/730 C Luft- und Raumfahrt - T-Kopf-Passschrauben, aus hochwarmfester Nickelbasislegierung NI-P101HT (Waspaloy), blank fr hohe Muttern - Klasse: 1 210 MPa/730 C This European Standard w

7、as approved by CEN on 3 November 2007. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such

8、national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language

9、and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxemb

10、ourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rig

11、hts of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3294:2008: E2 Contents Page 1 Scope 4 2 Normative references 4 3 Required characteristics.4 3.1 Configuration, dimensions, tolerances, masses4 3.2 Material .4 3.3 Surface treatment 4 3.4 Thread

12、surface .4 4 Designation 8 5 Marking .8 6 Technical specification .8 Figures Figure 1 Configuration 5 Tables Table 1 Dimensions. 5 Table 2 Lengths and masses . 6 BS EN 3294:20083 Foreword This document (EN 3294:2008) has been prepared by the Aerospace and Defence Industries Association of Europe - S

13、tandardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard s

14、hall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2008, and conflicting national standards shall be withdrawn at the latest by October 2008. Attention is drawn to the possibility that some of the elements of this d

15、ocument may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standar

16、d: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS

17、 EN 3294:20084 1 Scope This standard specifies the dimensions of uncoated T-head bolts, close tolerance, with MJ-thread, thread length for increased height nuts, in heat resistant nickel base alloy NI-P101HT for aerospace applications. Maximum test temperature of the parts is 730 C. These bolts are

18、to be used in aerospace fastening systems mainly stressed in shearing force. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the refer

19、enced document (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace products1)EN 2582, Aerospace series Bolts in heat resisting nickel base alloy NI-P101HT (Waspaloy) Classification: 1 210 MPa/730 C Technical specification1)EN 2959, Aerospace series Heat resisting alloy

20、 NI-PH1302 (NiCr20Co13Mo4Ti3Al) Solution treated and cold worked Bar for forged fasteners 3 mm D 30 mm1)EN 3220, Aerospace series Heat resisting nickel base alloy (Ni-P101 HT) Cold worked and softened Bar and wire for continuous forging or extrusion for fasteners 3 D 30 mm1)ISO 3353-1, Aerospace Lea

21、d and runout threads Part 1: Rolled external threads ISO 5855-1, Aerospace MJ threads Part 1: General requirements ISO 5855-2, Aerospace MJ threads Part 2: Limit dimensions for bolts and nuts 3 Required characteristics 3.1 Configuration, dimensions, tolerances, masses Configuration shall be in accor

22、dance with the figure. Dimensions, tolerances and masses shall conform to Figure 1 and Tables 1 and 2. Details of form, not stated are at the manufacturers option. 3.2 Material Heat resisting nickel base alloy NI-P101HT according to EN 2959 or EN 3220. 3.3 Surface treatment None. 3.4 Thread surface

23、See Figure 1. 1) Published as AECMA Prestandard at the date of publication of this standard. BS EN 3294:20085 Dimensions in millimetres Break sharp edges 0,1 mm to 0,4 mm aWhen the length of the shank is less than one time the nominal value of the shank diameter, D, the run-out is measured at a dist

24、ance equal to half the actual shank length bTotal straightness with reference to nominal length N cFor bolts having a shank length less than one time the nominal value of the shank diameter, D, the pitch diameter axis shall be used as datum dRolled eThread runout ISO 3353-1 fThread pitch diameter gT

25、hread major diameter max.: actual shank diameter minus 0,025 mm; min.: defined by 6h tolerance hLead thread ISO 3353-1 iR0,90,4 typicaljIdentity marking Figure 1 Configuration Table 1 Dimensions Dimensions in millimetres C D E K Q R S X Y Code Designationa max. min. f7 max. min. max. min. 0,5 max. m

26、in. max. min. 050 MJ5 0,8 4h6hb 6,3 6,1 5 11,6 11,1 3,4 2,9 3,5 0,5 0,3 8,4 8,1060 MJ6 1 4h6hb7,3 7,1 6 12,5 12,0 3,9 3,4 4,2 0,7 0,5 9,5 9,20,12070 MJ7 1 4h6hb8,4 8,2 7 13,9 13,4 4,5 4,0 5,2 0,7 0,5 10,5 10,2080 MJ8 1 4h6hb9,4 9,2 8 14,5 14,0 5,0 4,5 6,2 0,7 0,5 11,5 11,20,002 100 MJ10 1,25 4h6hb11

27、,2 11,0 10 17,0 16,5 5,8 5,3 7,9 0,8 0,6 13,3 13,0 0,001 50,15aAccording to ISO 5855-1 and ISO 5855-2. bThe tolerance on the thread major diameter shall be modified as shown in Figure 1. BS EN 3294:20086 Table 2 Lengths and masses Masses (8,25 kg/dm3): kg/1 000 pieces Nominal diameter code 050 060 0

28、70 080 100 L 0,2 N Mass N Mass N Mass N Mass N Mass Length code mm mm kg mm kg mm kg mm kg mm kg 003 3 18 4,74 20 7,15 004 4 19 4,90 21 7,38 22 10,75 23 14,47 005 5 20 5,07 22 7,62 23 11,07 24 14,88 27 25,11 006 6 21 5,23 23 7,85 24 11,38 25 15,29 28 25,76 007 7 22 5,39 24 8,08 25 11,70 26 15,71 29

29、26,41 008 8 23 5,55 25 8,31 26 12,02 27 16,12 30 27,05 009 9 24 5,71 26 8,55 27 12,34 28 16,54 31 27,70 010 10 25 5,87 27 8,78 28 12,66 29 16,95 32 28,35 011 11 26 6,04 28 9,01 29 12,97 30 17,36 33 29,00 012 12 27 6,20 29 9,25 30 13,29 31 17,78 34 29,64 013 13 28 6,36 30 9,48 31 13,61 32 18,20 35 30

30、,29 014 14 29 6,52 31 9,71 32 13,92 33 18,63 36 30,93 015 15 30 6,69 32 9,93 33 14,24 34 19,02 37 31,59 016 16 31 6,85 33 10,18 34 14,56 35 19,44 38 32,23 017 17 32 7,01 34 10,41 35 14,88 36 19,85 39 32,88 018 18 33 7,17 35 10,65 36 15,19 37 20,27 40 33,53 019 19 34 7,33 36 10,88 37 15,51 38 20,68 4

31、1 34,18 020 20 35 7,50 37 11,11 38 15,83 39 21,10 42 34,82 021 21 36 7,66 38 11,35 39 16,14 40 21,51 43 35,47 022 22 37 7,82 39 11,58 40 16,46 41 21,93 44 36,12 023 23 38 7,98 40 11,81 41 16,78 42 22,34 45 36,77 024 24 39 8,14 41 12,05 42 17,10 43 22,75 46 37,41 025 25 40 8,31 42 12,28 43 17,41 44 2

32、3,17 47 38,06 026 26 41 8,48 43 12,51 44 17,73 45 23,58 48 38,71 027 27 42 8,63 44 12,74 45 18,05 46 24,00 49 39,36 028 28 43 8,79 45 12,98 46 18,37 47 24,41 50 40,00 029 29 44 8,95 46 13,21 47 18,68 48 24,83 51 40,65 030 30 45 9,12 47 13,44 48 19,00 49 25,24 52 41,30 032 32 48 9,57 50 14,08 51 19,8

33、5 52 26,38 55 43,15 034 34 50 9,89 52 14,56 53 20,53 54 27,24 57 44,44 036 36 52 10,22 54 15,02 55 21,17 56 28,07 59 45,74 038 38 54 10,54 56 15,49 57 21,80 58 28,90 61 47,03 040 40 56 10,86 58 15,96 59 22,43 60 29,73 63 48,33 042 42 58 11,19 60 16,42 61 23,07 62 30,56 65 49,62 044 44 60 11,51 62 16

34、,89 63 23,70 64 31,38 67 50,92 046 46 62 11,84 64 17,36 65 24,34 66 32,21 69 52,21 048 48 64 12,16 66 17,82 67 24,97 68 33,04 71 53,51 BS EN 3294:20087 Table 2 (continued) Masses (8,25 kg/dm3): kg/1 000 pieces Nominal diameter code 050 060 070 080 100 L 0,2 N Mass N Mass N Mass N Mass N Mass Length

35、code mm mm kg mm kg mm kg mm kg mm kg 050 50 66 12,48 68 18,29 69 25,61 70 33,87 73 54,80 052 52 70 18,75 71 26,24 72 34,70 75 56,10 054 54 72 19,22 73 26,88 74 35,53 77 57,39 056 56 74 19,69 75 27,51 76 36,36 79 58,69 058 58 76 20,15 77 28,15 78 37,19 81 59,98 060 60 78 20,62 79 28,78 80 38,03 83 6

36、1,28 062 62 81 29,42 82 38,85 85 62,47 064 64 83 30,05 84 39,67 87 63,97 066 66 85 30,68 86 40,50 89 65,16 068 68 87 31,32 88 41,33 91 66,46 070 70 89 31,95 90 42,16 93 67,75 072 72 92 42,99 95 69,05 074 74 94 43,82 97 70,34 076 76 96 44,65 99 71,64 078 78 98 45,48 101 72,93 080 80 100 46,30 103 74,

37、23 082 82 105 75,52 084 84 107 76,82 086 86 109 78,11 088 88 111 79,41 090 90 113 80,70 092 92 115 82,00 094 94 117 83,29 096 96 119 84,59 098 98 121 85,88 100 100 123 87,18 BS EN 3294:20088 4 Designation Each T-head bolt, close tolerance, shall only be designated as in the following example: Descri

38、ption block Identity block Bolt EN 3294 080 050 Number of EN standard Nominal diameter code (see Table 1) Length code (see Table 2) If necessary the originator code I9005 shall be placed between the description block and the identity block. 5 Marking Each T-head bolt, close tolerance, shall be marke

39、d in accordance with EN 2424, Style A. 6 Technical specification The T-head bolts, close tolerance, shall conform to the requirements of EN 2582. BS EN 3294:2008blankBS EN 3294:2008BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible

40、for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or

41、editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the

42、 inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publicat

43、ions should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that

44、 have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are al

45、so available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of

46、standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI i

47、s available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > 其他

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1