1、BS EN 486:2009ICS 77.150.10NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAluminium andaluminium alloys Extrusion ingots SpecificationsThis British Standardwas published underthe authority of theStandards Policy andStrategy Committee on 30September 2009 BSI 200
2、9ISBN 978 0 580 62123 9Amendments/corrigenda issued since publicationDate CommentsBS EN 486:2009National forewordThis British Standard is the UK implementation of EN 486:2009. Itsupersedes BS EN 486:1994 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee N
3、FE/35, Light metals and their alloys.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British St
4、andard cannot confer immunityfrom legal obligations.BS EN 486:2009EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 486August 2009ICS 77.150.10 Supersedes EN 486:1993 English VersionAluminium and aluminium alloys - Extrusion ingots -SpecificationsAluminium et alliages daluminium - Billettes de filag
5、e -SpcificationsAluminium und Aluminiumlegierungen - Pressbarren -SpezifikationenThis European Standard was approved by CEN on 24 July 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a nation
6、al standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any
7、other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia
8、, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES
9、KOMITEE FR NORMUNGManagement Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 486:2009: EBS EN 486:2009EN 486:2009 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms a
10、nd definitions .44 Ordering information .45 Requirements .55.1 Production and manufacturing processes .55.2 Chemical composition 55.3 Surface and internal quality 55.4 Tolerances on dimensions .66 Test procedures .66.1 Analysis of chemical composition .66.2 Homogenizing treatment .76.3 Other tests 7
11、7 Inspection documents .77.1 Certificate of mass and analysis 77.2 Inspection certificate .78 Marking .79 Packaging, transport and storage 810 Complaints .8Bibliography 9BS EN 486:2009EN 486:2009 (E) 3 Foreword This document (EN 486:2009) has been prepared by Technical Committee CEN/TC 132 “Aluminiu
12、m and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2010, and conflicting national standards shall be withdrawn at the late
13、st by February 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 486:1993. Within its programme of wor
14、k, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 2 “Extrusion billets and rolling ingots“ to revise EN 486:1993. CEN/TC 132 affirms its policy that in the case when a patentee refuses to grant licences on standardised standard products under reasonable and not discriminatory conditions, the
15、n this product shall be removed from the corresponding standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Fin
16、land, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 486:2009EN 486:2009 (E) 4 1 Scope This European Standard specifies the g
17、eneral requirements to be met by extrusion ingots of aluminium and aluminium alloys obtained by semi-continuous or continuous casting, from primary or recycled metal, for general engineering applications. 2 Normative references The following referenced documents are indispensable for the application
18、 of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 573-1, Aluminium and aluminium alloys Chemical composition and form of wrought products Part 1: Numerical designation
19、system EN 573-2, Aluminium and aluminium alloys Chemical composition and form of wrought products Part 2: Chemical symbol based designation system EN 573-3, Aluminium and aluminium alloys Chemical composition and form of wrought products Part 3: Chemical composition EN 10204, Metallic products Types
20、 of inspection documents EN 12258-1:1998, Aluminium and aluminium alloys Terms and definitions Part 1: General terms EN 14242, Aluminium and aluminium alloys Chemical analysis Inductively coupled plasma optical emission spectral analysis EN 14726, Aluminium and aluminium alloys Chemical analysis Gui
21、deline for spark optical emission spectrometric analysis 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12258-1:1998 and the following apply. 3.1 heat quantity of liquid metal that has simultaneously undergone the same preparatory treatment in the fu
22、rnace before the casting operation 3.2 bundle set of ingots held together by suitable means for their transport 4 Ordering information The ordering information shall define the product required and shall contain the following: a) the form of the product (extrusion ingot); BS EN 486:2009EN 486:2009 (
23、E) 5 b) the designation of the aluminium or aluminium alloy according to EN 573-1 and EN 573-2 (or the purchaser alloy designation after agreement between supplier and purchaser). Tighter limits than the composition limits stated in EN 573-3 may be specified as required; c) whether as cast or homoge
24、nized; the word “homogenized“ can be replaced by the abbreviation “HO“. Other abbreviations shall be agreed between the supplier and the purchaser; d) the number of this European standard; e) the nominal dimensions of the product (i.e. diameter and length) expressed in millimetres. For hollow ingots
25、 and ingots other than round, dimensions and tolerances shall be given with reference to a drawing; f) quantity: 1) mass (in metric tonnes); 2) quantity tolerances if required; g) any requirements for inspection documents (see Clause 7); h) any additional requirements agreed between supplier and pur
26、chaser. 5 Requirements 5.1 Production and manufacturing processes If no special requirement has been agreed between supplier and purchaser, the manufacturing process, including homogenizing, is the manufacturers responsibility. In the case of special requirements, it is recommended that trial quanti
27、ties be produced to confirm that requirements are met. It is also recommended that the purchaser asks the manufacturer to advise of any significant change in the manufacturing processes which may affect the quality of the final product. It is recommended that a quality assurance system be implemente
28、d as described in EN ISO 9000 and EN ISO 9004. 5.2 Chemical composition The chemical composition of the ingots shall conform to the compositions specified in EN 573-3. It should preferably conform to the numerical designation. 5.3 Surface and internal quality Extrusion ingots shall: a) be free of ca
29、sting surface defects, handling marks, oil, dirt and corrosion; b) be free of inclusions, porosity and cracks; c) have a suitable metallurgical structure; to a standard suitable for extrusion and subsequent processing. Unless otherwise agreed between purchaser and supplier, the grain size is not gua
30、ranteed. BS EN 486:2009EN 486:2009 (E) 6 5.4 Tolerances on dimensions 5.4.1 Diameter (round ingots) The measurements shall be taken at the two sawn ends, on two diameters 90 apart. The tolerance on the nominal diameter is: a) 02mm for ingot diameters not larger than 200 mm; b) 03mm for ingot diamete
31、rs larger than 200 mm and not larger than 400 mm; c) 04mm for ingot diameters larger than or equal to 400 mm. 5.4.2 Length The length is measured overall after sawing. The tolerance is: a) 3 mm for ingot lengths not longer than 1 200 mm; b) 15 mm for ingot lengths longer than 1 200 mm. 5.4.3 Squaren
32、ess Sawn ends of extrusion ingots shall be square to 0,5. 5.4.4 Straightness The deflection, measured as arrow height on the centre of the curvature side, shall be less than 3 mm per metre with a maximum of 15 mm over the full length of the ingot. 5.4.5 Other dimensions For hollow ingots and ingots
33、other than round, tolerances shall comply with the specifications in the order. 6 Test procedures 6.1 Analysis of chemical composition The analytical samples shall be taken at the discretion of the manufacturer who shall use methods accepted at European level, EN 14242 and EN 14726, or at Internatio
34、nal level. The analytical samples shall be taken during the cast, from the metal distribution system, after the grain refiner addition (if any). The analytical samples shall be suitably machined and when analysed by emission spectrometry, shall be subject to at least two determinations. The sample r
35、esult is the arithmetic mean of the determinations. BS EN 486:2009EN 486:2009 (E) 7 The final result is the arithmetic mean of the results of the taken samples. For cast acceptance, each sample shall meet the specified composition limits. The manufacturer shall use analytical methods standardized at
36、 European or International level. The choice of appropriate methods is at the discretion of the manufacturer. 6.2 Homogenizing treatment The homogenizing treatment is generally required. The manufacturer shall take suitable measures to guarantee the quality and reproducibility of homogenizing, espec
37、ially by: a) periodic inspection and testing of the treated metal; b) periodic checks of the actual temperature of the ingots during treatment; c) adoption of procedures to achieve satisfactory reproducibility of the treatment. The homogenizing treatment shall be closely monitored by the manufacture
38、rs quality control system. 6.3 Other tests If required, other tests should be specified in the order after agreement between supplier and purchaser. 7 Inspection documents 7.1 Certificate of mass and analysis The supplier shall provide with each delivery a certificate of mass and analysis, which sha
39、ll contain the following information: a) the name and address of the supplying company and the name of the manufacturing plant; b) the name and address of the purchaser; c) the description of the product as described in 4a), 4b), 4c) and 4e); d) the cast numbers, the number of extrusion ingots of ea
40、ch cast and, for each cast, the actual analysis of the elements (silicon, iron, copper, manganese, magnesium, chromium, zinc, titanium and other elements specified in EN 573-3 or required in the order) in the sequence given in EN 573-3; NOTE Horizontal casting of extrusion ingot may comprise several
41、 heats per cast. In this case, the above information should be supplied for each heat. e) the total delivered net mass. 7.2 Inspection certificate Unless otherwise indicated in the order, the supplier shall deliver an inspection certificate 3.1 according to EN 10204 with at least the result of chemi
42、cal analysis. 8 Marking BS EN 486:2009EN 486:2009 (E) 8 Each extrusion ingot shall be marked with at least the following: a) cast number; b) designation of the aluminium or the aluminium alloy as per the order; c) manufacturer identification (e.g. logo, brand name); d) HO or any other agreed abbrevi
43、ation if the ingot is homogenized. Labelling of each bundle shall be undertaken when agreed upon between supplier and purchaser. 9 Packaging, transport and storage Extrusion ingots shall be packaged in bundles suitable for safe forklift truck handling. Specific packaging requirements may be agreed b
44、etween the purchaser and the supplier and shall be included in the order. Transport and storage conditions shall maintain the extrusion ingots in a condition suitable for extrusion without the necessity of further operations. 10 Complaints External and internal defects can give rise to complaints if
45、 they affect the processing or the end use of the ingot. The purchaser shall allow the supplier to check the grounds for complaint. For example, he shall present him with the following: a) a piece of faulty ingot, with its complete identification, and/or; b) a specimen of the finished product, or in
46、 an intermediate state, obtained from the faulty metal, with all the details allowing identification, and/or; c) justification of the defect in the ingot or finished product, and/or; d) details of conditions of processing and inspection in the intermediate stages. The dispute may entail the services
47、 of a referee laboratory to perform examination and tests. The supplier and purchaser shall agree on the laboratory and the examination and tests methods employed. BS EN 486:2009EN 486:2009 (E) 9 Bibliography 1 EN ISO 9000, Quality management systems Fundamentals and vocabulary (ISO 9000:2005) 2 EN
48、ISO 9004, Quality management systems Guidelines for performance improvements (ISO 9004:2000) BS EN 486:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for prep
49、aring BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an in
