1、BSI Standards PublicationPackaging of components for automatic handlingPart 4: Stick magazines for electronic components encapsulated in packages of different formsBS EN 60286-4:2013National forewordThis British Standard is the UK implementation of EN 60286-4:2013. It is identical to IEC 60286-4:201
2、3. It supersedes BS EN 60286-4:1998 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee EPL/40X, Capacitors and resistors for electronic equipment.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publicat
3、ion does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2013.Published by BSI Standards Limited 2013ISBN 978 0 580 72420 6ICS 31.020; 31.240Compliance with a British Standard cannot confer immunit
4、y fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 November 2013.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 60286-4:2013EUROPEAN STANDARD EN 60286-4 NORME EUROPENNE EUROPISCHE
5、NORM November 2013 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels 2013 CENELEC - All rights of exploitation in any form
6、 and by any means reserved worldwide for CENELEC members. Ref. No. EN 60286-4:2013 E ICS 31.020; 31.240 Supersedes EN 60286-4:1998 English version Packaging of components for automatic handling - Part 4: Stick magazines for electronic components encapsulated in packages of different forms (IEC 60286
7、-4:2013) Emballage des composants pour oprations automatises Partie 4: Magasins chargeurs pour composants lectroniques encapsuls dans des botiers de diffrentes formes (CEI 60286-4:2013) Gurtung und Magazinierung von Bauteilen fr automatische Verarbeitung - Teil 4: Stangenmagazine fr elektronische Ba
8、uelemente mit verschiedenen Gehusen (IEC 60286-4:2013) This European Standard was approved by CENELEC on 2013-08-30. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard withou
9、t any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any othe
10、r language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cypru
11、s, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
12、 United Kingdom. BS EN 60286-4:2013EN 60286-4:2013 - 2 - Foreword The text of document 40/2230/FDIS, future edition 3 of IEC 60286-4, prepared by IEC TC 40, “Capacitors and resistors for electronic equipment“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60286-4:2013.
13、The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2014-05-30 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2016-08-30
14、 This document supersedes EN 60286-4:1998. EN 60286-4:2013 includes the following significant technical changes with respect to EN 60286-4:1998: Clause 4 describes the guidelines for customer specific stick magazine design. It replaces the magazine design rules for IEC outlined components and rules
15、for orientation of components in stick magazines which have been moved to Annexes Z to D. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent righ
16、ts. Endorsement notice The text of the International Standard IEC 60286-4:2013 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following note has to be added for the standard indicated: ISO 11469 NOTE Harmonized as EN ISO 11469.
17、 BS EN 60286-4:2013- 3 - EN 60286-4:2013 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dat
18、ed references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year
19、Title EN/HD Year IEC 60191-3 1999 Mechanical standardization of semiconductor devices - Part 3: General rules for the preparation of outline drawings of integrated circuits EN 60191-3 1999 IEC 60747-1 + corr. August + A1 2006 2008 2010 Semiconductor devices - Part 1: General - - BS EN 60286-4:2013 2
20、 60286-4 IEC:2013 CONTENTS 1 Scope 5 2 Normative references . 5 3 Terms, definitions and conventions 5 3.1 Terms and definitions . 5 3.2 Conventions . 5 4 Shape and cross-section of stick magazine 6 5 Dimensions of stick magazines 7 5.1 General 7 5.2 Materials 8 5.3 Recycling . 8 6 Mechanical stabil
21、ity 8 7 End stoppers and spacers 9 8 Orientation of the components in the stick magazine 9 9 Marking . 9 Annex A (informative) DIL packages for through-hole mount . 10 Annex B (informative) SO packages for surface mounting . 12 Annex C (informative) Leaded chip carrier packages (PLCC) for surface mo
22、unting . 13 Annex D (normative) Rule for the orientation of integrated circuit packages in handling and shipping carriers such as stick magazines and rails (from IEC 60191-3:1999, Annex G) . 14 Bibliography 16 Figure 1 Shape and cross-sections of stick magazines . 6 Figure 2 Schematic of stick magaz
23、ine design and schematic of package profile 7 Figure A.1 DIL packages for through-hole mounting 10 Figure B.1 SO packages for surface mounting 12 Figure C.1 Leaded chip carrier packages (PLCC) for surface mounting . 13 Figure D.1 Five examples of the terminal No. 1 marking locations . 15 Table 1 Tol
24、erances to the package profile dimensions 7 Table 2 Principle of stick magazine requirements . 8 Table 3 Material reference for magazines and stoppers 8 Table A.1 e1= 3 modules e 10 Table A.2 e1= 4 modules e 11 Table A.3 e1= 6 modules e 11 Table B.1 Stick magazine dimensions for SO packages 12 Table
25、 C.1 Stick magazine dimensions for PLCC packages 13 BS EN 60286-4:201360286-4 IEC:2013 5 PACKAGING OF COMPONENTS FOR AUTOMATIC HANDLING Part 4: Stick magazines for electronic components encapsulated in packages of different forms 1 Scope This part of IEC 60286 is applicable to stick magazines (inclu
26、ding end stoppers) intended to be used for storage of electronic components, for transport from the manufacturer to the customer and for in-house use in the manufacturing plant. They are also used to feed automatic placement machines for surface mounting as well as for through-hole mounting of elect
27、ronic components. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (i
28、ncluding any amendments) applies. IEC 60191-3:1999, Mechanical standardization of semiconductor devices Part 3: General rules for the preparation of outline drawings of integrated circuits IEC 60747-1:2006, Semiconductor devices Part 1: General Amendment 1:2010 3 Terms, definitions and conventions 3
29、.1 Terms and definitions For the purposes of this document, the following definitions apply. 3.1.1 stick magazine elongated container which has an appropriate cross section designed to accommodate devices Note 1 to entry: Alternative terms such as tube, rail and magazine may be used. 3.1.2 end stopp
30、ers mechanism placed at each end of the stick magazine to keep the devices from falling out of the stick magazine Note 1 to entry: Alternative terms such as pins, plugs, end plugs, nails, retainers etc. may be used, but for the purposes of this standard “end stopper“ shall be used. 3.2 Conventions A
31、ll dimensions in tables and figures representing sizes are in millimetres. All dimensions in tables and figures representing angles or radii are in degrees. BS EN 60286-4:2013 6 60286-4 IEC:2013 4 Shape and cross-section of stick magazine Examples of typical and customized cross-sections for stick m
32、agazines are given in Figure 1. Customized form IEC 1734/13 Figure 1 Shape and cross-sections of stick magazines Internal stick magazine configuration shall be such that the individual component is protected from damage, maintains a fixed orientation and slides freely when one end is elevated at a m
33、inimum angle of 30. As magazine material over time is changing, the level of elevation of 30 may not be sufficient for freely sliding of components. In this case, to allow proper transition of the component from the magazine to a horizontal surface, the level of elevation should be kept to a minimum
34、. BS EN 60286-4:201360286-4 IEC:2013 7 5 Dimensions of stick magazines 5.1 General Because the shape of the cross-section varies, the controlled distance tolerances should conform to the values in Table 1, Table 2 and Figure 2. This table provides the tolerances to the package profile dimensions, wh
35、ich is a summary of the tolerances for various standard outlines (see Annexes A, B and C). A B D E C H A2A3e1HET IEC 1735/13 Schematic of stick magazine design Schematic of package profile IEC 1736/13 L Figure 2 Schematic of stick magazine design and schematic of package profile Table 1 Tolerances t
36、o the package profile dimensions Functional cross reference Tolerances to package profile dimensions Stick magazine Package profile A H Package dimension + 0,5 0,0B A3C HED A2Package dimension 0,2 E e1NOTE 1 A2is the body height of the component. NOTE 2 A3is the total package height of the component
37、. NOTE Additional protection of the component can be given by individual design to prevent cross traversing to the stick magazine length (prevention of bend leads). BS EN 60286-4:2013 8 60286-4 IEC:2013 Table 2 Principle of stick magazine requirements Dimension Nominal value and tolerances All radii
38、 0,5 to 1,5 L 530 mm max. T 0,6 mm 0,15 / +0,2 5.2 Materials The material shall be conductive, static dissipative or antistatic (a measuring method and requirements are under consideration). The loaded magazines shall be suitable to withstand transport and storage without danger of giving off vapour
39、s or of contaminating the surface of the terminations, which could make soldering difficult or deteriorate the component properties or terminations by chemical action. As a minimum, the component device type, manufacturers name or trade mark and date code shall be legible without removal of the comp
40、onents from the stick magazine. Where the stick material is not transparent, a suitable window or a series of windows/holes shall be provided for inspection purposes. 5.3 Recycling Stick magazines should be made of recyclable material. When such material is used the magazine shall be permanently mar
41、ked with the recycling symbol. The end-stoppers should be of the same material as the stick magazine. This does not apply to PVC-free type stick magazines, see Table 3. Table 3 Material reference for magazines and stoppers Magazine type Magazine material Stopper material PVC type PVC (hard type) PVC
42、 (soft type) PVC free type PVC free (e.g. PC or PET) PVC free (e.g. Elastomer (thermoplastic) ISO 11469 should be used. 6 Mechanical stability The mechanical stability of a loaded magazine during storage, transport and use shall be such that the components are adequately retained, without deformatio
43、n of the terminations or other damage, in order to maintain their orientation within the magazine, yet enabling them to be easily removed. The magazine, which should not exceed 530 mm in length, shall also be suitable for use with automatic placement machines or test equipment, and should be capable
44、 of bending in the length axis through a radius of 600 mm. They shall be so designed that they can be stacked in the machines and shall not overturn. BS EN 60286-4:201360286-4 IEC:2013 9 7 End stoppers and spacers End stoppers may be used to close the ends of the stick magazines, and spacers may be
45、used to limit the movement of the components within the stick magazines. For end stoppers and spacers the following rules apply: a) They shall be of any suitable material, preferably recyclable. When such a material is used and size permits, end stoppers and spacers shall be marked with the recyclin
46、g symbol. b) They shall be of static dissipative or antistatically-coated material, and spacers shall be of adequate compliance to prevent component damage. c) End stoppers shall stay in place at the ends of the magazines until they are intentionally removed, and shall be easily removable to dispers
47、e the devices without damaging the stick magazines. 8 Orientation of the components in the stick magazine See IEC 60191-3:1999, Annex G. Rule (see also Annex D). Integrated circuit packages shall be put in stick magazines with the terminal No. 1 mark orientation. The side with the mark has to exit f
48、irst from the carrier. When the packages are in the carrier and viewed from the top, the terminal No. 1 mark shall be left or in the lower left corner, and component marking shall be readable from the left to right. 9 Marking The magazines shall be marked “Dissipative“ or “Antistatic“ as applicable.
49、 The direction of unloading shall be marked on the magazines. If the components are electrostatically sensitive and require special precautions during handling, the magazines shall also be marked as required in Clause 8 of IEC 60747-1:2006, Amendment 1:2010. BS EN 60286-4:2013 10 60286-4 IEC:2013 Annex A (informative) DIL packages for through-hole mount See IEC 60191-2, code 050G:1978, code 51G:1987 and code 60G:1987. The principle of the functional
