1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationConnectors for electronic equipment Tests and measurementsPart 8-1: Static load tests (fixed connectors) Test 8a: Static load, transverseBS EN 60512-8-1:2010National forewordThis
2、 British Standard is the UK implementation of EN 60512-8-1:2010. It isidentical to IEC 60512-8-1:2010. It supersedes Test 8a from BS 5772-5:1993,IEC 60512-5:1992, which will remain current until all the tests it containshave been revised.The UK participation in its preparation was entrusted to Techn
3、ical CommitteeEPL/48, Electromechanical components and mechanical structures for electronic equipment.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are res
4、ponsible for its correct application. BSI 2010ISBN 978 0 580 62114 7ICS 31.220.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 30 November 2010.Amendments issued
5、 since publicationDate Text affectedBRITISH STANDARDBS EN 60512-8-1:2010EUROPEAN STANDARD EN 60512-8-1 NORME EUROPENNE EUROPISCHE NORM September 2010 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnisc
6、he Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60512-8-1:2010 E ICS 31.220.01 English version Connectors for electronic equipment - Tests and measurements - P
7、art 8-1: Static load tests (fixed connectors) - Test 8a: Static load, transverse (IEC 60512-8-1:2010) Connecteurs pour quipements lectroniques - Essais et mesures - Partie 8-1: Essais sous charge statique (embases) - Essai 8a: Charge statique transversale (CEI 60512-8-1:2010) Steckverbinder fr elekt
8、ronische Einrichtungen - Mess- und Prfverfahren - Teil 8-1: Prfungen mit statischer Last (feste Steckverbinder) - Prfung 8a: Statische Querlast (IEC 60512-8-1:2010) This European Standard was approved by CENELEC on 2010-09-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulat
9、ions which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This
10、European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members
11、are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, S
12、lovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 60512-8-1:2010 - 2 - Foreword The text of document 48B/2154/FDIS, future edition 1 of IEC 60512-8-1, prepared by SC 48B, Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic equipment, was submi
13、tted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60512-8-1 on 2010-09-01. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
14、rights. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2011-06-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2013-09-01 An
15、nex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60512-8-1:2010 was approved by CENELEC as a European Standard without any modification. _ BS EN 60512-8-1:2010- 3 - EN 60512-8-1:2010 Annex ZA (normative) Normative references to international publicati
16、ons with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies
17、. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60512-1-1 - Connectors for electronic equipment - Tests and measurements - Part 1-1: General examination - Test 1a: Visual examina
18、tion EN 60512-1-1 - BS EN 60512-8-1:2010 4 60512-8-1 IEC:2010 CONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 8-1: Static load tests (fixed connectors) Test 8a: Static load, transverse 1 Scope and object This part of IEC 60512, when required by the detail specification, is used for t
19、esting connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to detail a standard test method to assess the suitability of a fixed connector for use in applications where it may be subje
20、ct to transverse stresses. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
21、 IEC 60512-1-1, Connectors for electronic equipment Tests and measurements Part 1-1: General examination Test 1a: Visual examination 3 Preparation of the specimen The specimen shall not be wired but shall be fitted with such accessories as may be required by the detail specification. Unless otherwis
22、e specified, the specimen shall be mounted in the normal manner, using the normal panel or chassis cut-out as laid down in the detail specification. NOTE The plate should be strong enough to sustain the applied forces. The length and width of the plate should be such that the contour of the specimen
23、 is exceeded. 4 Test method A specified force shall be applied to the specimen at the point and in the direction(s) as specified in the detail specification. This force shall be steadily increased up to the specified value and, unless otherwise specified in the detail specification, maintained for 1
24、 min. Unless otherwise specified in the detail specification, the force shall be parallel to the mounting plate. 5 Final measurements a) Visual examination (IEC 60512-1-1, test 1a). b) Applicable operational characteristics. NOTE if applicable, the detail specification may require a sealing test fro
25、m the IEC60512-14 series or an ingress protection test according IEC 60529. BS EN 60512-8-1:201060512-8-1 IEC:2010 5 6 Requirements There shall be no damage which would impair normal operation. 7 Details to be specified When this test is required by the detail specification, the following details sh
26、all be specified: a) mounting of the specimen, including dimensions of the panel cut-out; b) type of accessories, if required; c) value of the force, and the rate of increase; d) location, direction(s) and duration of the application of the force; e) shape of the fixture or tool used for applying th
27、e force; f) requirements for final measurements; g) any deviation from the standard test method. _ BS EN 60512-8-1:2010This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publica
28、tions, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +4
29、4 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or a
30、mbiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat s
31、ubscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and f
32、oreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise r
33、equested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its
34、products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel:
35、+44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of th
36、e publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior writ
37、ten permission from BSI. This does not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email:
