1、STD-BSI BS EN bLLbS-3L-ENGL 2000 Lb24bb9 0824879 597 .I BRITISH STANDARD Radio-frequency connectors - Part 31: RF coaxial connectors with inner diameter of outer conductor 1,O mm (0,039in) with screw coupling - Characteristic impedance 50 ohms(type 1,O) The European Standard EN 6116931:1999 has the
2、status of a British Standard ICs 33.120.30 NO COPYING WiTHOUT BSI PERMISSION EXCEPT AS PEBMIITED BY COPYRIGHT LAW BS EN il 169-3 1:ZOOO IEC i 1169-3 1: 1999 223100:1999 STD-BSI BS EN bLLb9-3L-ENGL 2000 lb24bb9 0824880 209 111 BS EN 61169-31:2000 Amd. No. This British Standard, having been prepared u
3、nder the direction of the Electrokchnid Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 January 2000 Date Comments - National foreword This British Standard is the English language version of EN 61169-31:1999. It is identical with IEC 61169-
4、31:1999. This standard is a harmonized specification within the IEC quality assessment system for electronic components (IECQ). In the IECQ system, this specification is numbered QC 223100. The UK participation in its preparation was entrusted by Technical Committee EPIJ46, Cables, wires, waveguides
5、, RF connectors and accessories for communication and signalling, to Subcommittee EPIJ462, RF connectors and waveguides, which has the responsibility to: - aid enquirers to undersand the text; - present to the responsible intrnational/European committee any enquiries on the interpretation, or propos
6、als for change, and keep the UK interests informed; - monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this Subcommittee can be obtained on request to its secretary. From 1 January 1997, aU IEC publications have the number
7、60000 added to the old number. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC S
8、tandards normaily include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement intedonal or European publications referred to in this document may be found in the BSI Standards Catalogue under th
9、e section entitled “International Standards Correspondence Index“, or by using the “Find“ facility of the BSI Standards Electronic Caialogue. A British Standard does not purport to include ali the necessasy provisions of a contract Users of British Standards are responsible for their correct applica
10、tion. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 24, an inside back cover and a back cover. The BSI copynght notice displayed in this docume
11、nt indicates when the document was last issued. Amendments issued since publication O BSI 01-2000 ISBN O 580 35903 4 STD-BSI BS EN 61367-3L-ENGL 2000 ILI 3624669 082483 145 9 EUROPEAN STANDARD EN 61169-31 NO= EUR0PEE”E EUROP- Nom October 1999 ICs 33.120.30 English version Radiefkquency connectors -
12、Part 31: RF coaxial connectors with inner diameter of outer conductor 1,0 mm (0,039 in) with screw couphg - Charaderistic impdance - 50 ohms (type 1,O) wc 61 16!3-31:1999) connecteurs pour fr-quences radioelctriques Partie 31: connecteuiS coaxiaux pour Mquences radiolrcn?“. detail A 0,Ol A a b Note
13、2 2,700 2,900 0,106 0,114 0,450 0,550 0,018 0,022 Reference d/T I-, C d e plane (0,0005) Detail A Before slotting and forming 1,300 - 0,051 - 0,000 0,050 0,000 0,002 2,380 2,400 0,094 0,095 f 9 h IEC 1061B9 0,9975 1,0025 0,03927 0,03947 - 0,013 - 0,0005 0,025 0,076 0,001 0,003 j k I I 0,070 0,150 0,
14、0028 0,0059 0.432 0,436 0,01701 0,01717 m n 2,950 3,050 0,116 0,120 1,600 1,700 0,063 0,067 I 1 I I I I 3,750 I - I 0,148 I - I NOTE 1 Mechanical and electrical reference plane NOTE 2 Surface finish: 0,4 pm (16 pin) max. NOTE 3 Socket contact configuration optional. Dimension to meet reflection fact
15、or requirement, mating character- istics and connector durability when mated with a 0,250 mm i 0,005 mm (0,0098 in f 0,0002 in) diameter pin. Figure 4 - Connector with socket centre contact O BSI 01-2000 STD.BS1 BS EN bLLbS-31-ENGL 2000 I Lb24bb9 0824889 436 Page 9 EN 61169-31:1999 2.1.3 Gauges Mill
16、imetres are original dimensions. All undimensioned pictorial configurations are for reference purposes only. 2.1.3.1 Mechanical gauges 2.1.3.2 Socket connector 2.1.3.3 Centre contact Blend radius 0.2 mrn (0,008 in) max. in) rnax III b I IEC 1062/99, Figure 5 - Gauge pins for centre contact of socket
17、 connector 2.1.3.4 Test sequence a) Steel test pin (figure 5) with a diameter a of 0,255 mm f 0,0015 mm (0,0100 in f 0,00006 in) and a length b of 0,68 mm to 1,02 mm (0,027 in to 0,040 in) shall be inserted once into the centre contact. b) A second steel test pin (figure 5) with a diameter a of 0,24
18、5 mm f 0,0015 mm (0,0096 in f 0,00006 in) and a length b of 1,09 mm to 1,65 mm (0,043 in to 0,065 in) and a 0,4 pm (16 pin) max finish shall be inserted into the centre contact. This gauge when in a vertical downward attitude shall be retained by the contact. This gauge will have a mass (weight) of
19、25 g. 3 Quality assessment procedures 3.1 General The following subclauses provide recommended ratings, performance and test conditions to be considered when writing a detail specification (DS). They also provide an appropriate schedule of tests with minimum levels of conformance inspection. Q BSI 0
20、1-2000 STD=BSI BS EN bLLb9-3L-ENGL 2000 Lb2Libb9 0824890 158 Page 10 3.2 Ratings and characteristics The r.f. connectors defined in this standard are designed for use with a variety of flexible and semi-rigid coaxial cables and in microwave integrated circuits and similar uncabled EN 61169-31:1999 a
21、pplications. Ratings and characteristics Electrical Nominal impedance Frequency range Reflection factor Grade 1 connectors O up to 50 GHz 50 GHz up to 75 GHz 75 GHz up to 110 GHz Grade O connectors O up to 50 GHz 50 GHz up to 75 GHz 75 GHz up to 110 GHz Centre contact resistance initial after condit
22、ioning Outer conductor continuity initial after conditioning Insulation resistance Voltage proof at sea level * at 4,4 kPa Environmental test voltage at sea level at 4,4 kPa Screening effectiveness at 1 GHz fully mated IEC 61169-1 Subclause 9.2.1 9.2.3 9.2.5 9.2.6 9.4.2 9.2.8 Value 50 R up to 110 GH
23、z 0,120 max. 0,150 max. 0,158 max. 0,063 max. 0,080 max. 0,158 max. 54 mR 510 ma 11,O mR 12,O mC2 25 Gs2 500 V or as limited by cable 100 Vor as limited by cable 150 V or as limited by cable 40 V or as limited by cable a, 2 90 dB Remarks - including any deviations from standard test methods Voltage
24、values are r.rn.s. values of a.c. at 40 Hz to 65 Hz unless otherwise stated. O BSI 01-2000 STDmBSI BS EN bLLb9-31-ENGL 2000 Lb24bb9 0824891 094 Page 11 EN 61169-31:1999 Ratings and characteristics Electrical Discharge test (corona) at sea level at 4,4 kPa Mechanical Soldering - bit size Gauge retent
25、ion resilient contacts - inner contact Centre contact captivation - axial force - permitted displacement in each direction - torque Engagement and separation Screw coupling Coupling torque - coupling nut friction - normal - proof Tensile strength of coupling mechanism Effectiveness of cable fixing a
26、gainst: I) cable rotation il) cable pulling Il) cable bending IV) cable torsion Bending moment Bump Vibration Shock IEC 61169-1 Subclause 9.2.9 9.3.2 9.3.4 9.3.5 9.3.6 9.3.11 9.3.7.2 9.3.8 9.3.9 9.3.10 9.3.12 9.3.13 9.3.3 9.3.14 Value See detail specification See detail specification See detail spec
27、ification 0,20 N 10 N See detail specification 0,007 Nm max 0,6 Nm 0,30 Nm to 0,41 Nm 0,7 Nm 220 N See detail specification 133 N (RG405) See detail specification 0,l Nm (RG405) See detail specification See detail specification 98 mis2 10 Hz to 2 O00 Hz 490 mis2 %sine 11 ms Remarks - Including any d
28、eviations from standard test methods Extinction voltages Achievable by hand Point of application and duration Duration of applied torque Relative to reference plane (1 O g acceleration) (50 g acceleration) Q BSI 01-2000 STD=BSI BS EN bLLb7-3L-ENGL 2000 811 Lb24bb7 0824892 T20 Page 12 EN 61169-31:199
29、9 Ratings and characteristics Environmental Preferred climatic categories components cables: - flexible cables: - semi rigid Sealing (panel and barrier sealed connector) Sealing (hermetically sealed connector) Additional environmental characteristics Endurance Mechanical High temperature Salt mist A
30、dditional endurance characteristics Chemical contamination Resistance to solvents and contaminating fluids, fluids to be used Sulphur dioxide exposure IEC 61169-1 Subclause 9.4.6 9.4.8 Value 5511 25121 5511 25/21 5511 15/21 1 cm Ih max. 5 Pa cm Is See detail specification See detail specification Se
31、e detail specification See detail specification See detail specification See detail specification See detail specification Remarks - including any deviations from standard test methods 100kPa-110kPa pressure differential 100kPa-110kPa pressure differential O BSI 01-2000 STD.BS1 BS EN bLLb9-31-ENGt 2
32、000 m Lb24bb9 0824893 9b7 Page 13 EN 61169-31:1999 3.3 Test schedule and inspection requirements Acceptance tests Test method subclause IEC 61169-1 Assessment level M (Higher) Assessment level H (Lower) - IL - II - s4 II s4 II II II s4 54 - s4 - Test required period Test required IL AQL YO Period AQ
33、L I Group A 1 Visual inspection 9.1.2 a a s3 - 53 s3 s3 s3 s3 s3 II s3 53 - 180 0.4 1 ,o 0,40 1 ,o 0,65 0,015 0,40 0.40 0,40 9.1.3.1 a a a ia ia ia a ia a a a ia ia ia a ia Group BI Outline dimensions Mechanical compatibility Engagement and separation Gauge retention (resilient contact) Sealing, non
34、-hermetic Sealing, hermetic Voltage proof Solderability piece parts Insulation resistance 9.1.3.3 9.3.6 Lot by lot Lot by lot 9.3.4 9.4.5.1 9.4.5.2 9.2.6 9.3.2.1.1 9.2.5 a a 4,O 3.3.1 Periodic tests There are no Group C tests for levels H and M. NOTE For details of symbols, abbreviations and procedu
35、res, see 3.4. O BSI 01-2000 Page 14 Periodic tests (continued) EN 61 169-3 1:1999 Number of specimen method Subclause IEC 61 169-1 Permittec failures per group Group D7 (d) Solderability connector assemblies Resistance to soldering heat Mechanical tests on cable fixing; i) cable rotation (nutation)
36、i) cable pulling iii) cable bending iv) cable torsion I 9.3.2.1.1 9.3.2.1.2 9.3.7.2 9.3.8 9.3.9 9.3.1 O Group 02 (d) Contact resistance, outer conductor and screen continuity, centre conductor continuity Vibration Damp heat, steady state 9.2.3 9.3.3 9.4.3 Assessment level M (Higher) Test required Je
37、riod 3 years 3 years Assessment level H (Lower) Test ,equired Number of ipecimen 3 3 Jermittec failures Per group 1 1 Period - 3 years 3 years NOTE For details of symbols, abbreviations and procedures see 3.4. O BSI 01-2000 STD-BSI BS EN bLLbS-31-ENGL 2000 1624bb9 0824895 73T Test Number specimen 1
38、required of a 6 a a 6 ia ia 6 ia a a 1# Permitted failures per group 1 1 I 1 Number of specimen 1 3 Permitted Period failures per group 1 3 years 1 3 years Page 15 EN 61169-311999 Periodic tests (concluded) Test method iubclause iC 61 169-1 Assessment level M (Higher) Assessment level H (Lower) - pe
39、riod - 3 fears - 3 vears - Test aquired a a a ;roup O3 9.1 3.2 limensions piece- ,arts and materials ;roup O4 (d) dechanical mdurance iigh temperature mdurance Sulphur dioxide 9.5 9.6 9.4.8 ;roup O5 (d) 3 years 9.2.1 ieflection factor Screening %ffectiveness Water immersion ia ia - 9.2.8 9.2.7 Group
40、 D6 (d) 3 years Contact captivation Rapid change of temperature Climatic sequence 9.3.5 9.4.4 9.4.2 ia a a - Group 07 (d) 3 years - 9.7 Resistance to solvents and contaminating fluids NOTE For details of svrnbols. abbreviations and Drocedures see 3.4. 3.4 Procedures 3.4.1 Quality conformance inspect
41、ion This shall consist of Test Groups Al and B1 on a lot-by-lot basis. 3.4.2 Qualification approval and its maintenance This shall consist of three consecutive lots passing Test Groups Al and B1 followed by selection of specimens from the lots as appropriate. These specimens shall successfully pass
42、the specified periodic D tests. O BSI 01-2000 Page 16 Details of symbols, abbeviations and procedures: EN 61169-31:1999 a = suggested as applicable ia na = not applicable IL = Inspection Level AQL = Acceptable Quality Level * # (d) = test suggested (if technically applicable) = one set of piece-part
43、s each style and variant, unless using common piece parts. = for Qualification Approval (QA) a total of 2 failures only permitted for level H and 1 failure = Group D7 - number of pairs for each solvent = destructive tests - specimens shall not be returned to stock. only for level M from groups Dl to
44、 D7 4 Instructions for preparation of detail specifications 4.1 General Detail specification (DS) writers shall use the appropriate BDS pro-forma. The following pages comprise the pro-forma BDS dedicated for use with 50 !2 type 1,O connectors. As such, it will have already entered on it information
45、relating to: a) the basic specification number applicable to all the detail specifications covering b) the connector series designation. The specification writer should enter the details relating to the connector style/variant(s) to be covered as indicated. The numbers in brackets on the BDS pro-for
46、ma correspond to the following indications which shall be given. connector styles of the series covered by the sectional specification; Identification of the detail specification The name of the National Standards Institution under whose authority the DS is published and, if applicable, the organiza
47、tion from whom the DS is available. The number allocated to the DS by the relevant National Authorized Institution immediately preceded by the IS0 two letter national identity code or “XX“ when DS is produced by an IEC technical committee. The number and issue number of the IEC generic specification
48、 and, when applicable, the sectional specification; also the national reference, if different. If different from the IEC number, the national number of the DS, date of issue and any further information required by the national system, together with any amendment num bers. Identification of the compo
49、nent Enter the following details: The style designation of the connector including type of fixing and sealing, if applicable. Attachment: Special features and markings: As applicable. By deletion of the inapplicable options of cable/wire: given for centre and outer conductors. O BSI 01-2000 STD-BSI BS EN LIIS-II-ENGL 2000 II lb24bb9 0824897 502 = Page 17 EN 61169-31:1999 (6) (7) Enter details of assessment level and the climatic category. A reproduction of the outline drawing and details of the panel piercing, if applicable. It shall provide the maximum e
