1、BRITISH STANDARDBS EN 61300-2-38: 2006Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-38: Tests Sealing for pressurized fibre optic closuresThe European Standard EN 61300-2-38:2006 has the status of a British StandardICS 33.180.20g49g50g3g38g50
2、g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 61300-2-38:2006This British Standard was published under the authority of the Standards Policy and Strategy
3、Committee on 31 January 2007 BSI 2007ISBN 978 0 580 50040 4National forewordThis British Standard was published by BSI. It is the UK implementation of EN 61300-2-38:2006. It is identical with IEC 61300-2-38:2006. It supersedes BS EN 61300-2-38:1997 which is withdrawn. The UK participation in its pre
4、paration was entrusted by Technical Committee GEL/86, Fibre optics, to Subcommittee GEL/86/2, Fibre optic interconnecting devices and passive components.A list of organizations represented on GEL/86/2 can be obtained on request to its secretary.This publication does not purport to include all the ne
5、cessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARD EN 61300-2-38 NORME EUROPENNE EUROPISCHE NORM November 2006
6、CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2006 CENELEC - All rights of exploitation in any form and by any means reserved
7、worldwide for CENELEC members. Ref. No. EN 61300-2-38:2006 E ICS 33.180.20 Supersedes EN 61300-2-38:1997English version Fibre optic interconnecting devices and passive components - Basic test and measurement procedures Part 2-38: Tests - Sealing for pressurized fibre optic closures (IEC 61300-2-38:2
8、006) Dispositifs dinterconnexion et composants passifs fibres optiques - Mthodes fondamentales dessais et de mesures Partie 2-38: Essais - Etanchit pour les botiers fibres optiques surpression interne (CEI 61300-2-38:2006) Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende P
9、rf- und Messverfahren Teil 2-38: Prfungen - Dichtheit druckfester Muffen fr Lichtwellenleiterbauteile (IEC 61300-2-38:2006) This European Standard was approved by CENELEC on 2006-10-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for g
10、iving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three officia
11、l versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committ
12、ees of Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
13、Foreword The text of document 86B/2346/FDIS, future edition 2 of IEC 61300-2-38, prepared by SC 86B, Fibre optic interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61300-2-38 on 2006-10-01. This
14、 European Standard supersedes EN 61300-2-38:1997. Specific technical changes from EN 61300-2-38:1997 include the specifications of more strict and more detailed sealing properties. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of a
15、n identical national standard or by endorsement (dop) 2007-07-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2009-10-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 61300-2-38:2006 was approved
16、by CENELEC as a European Standard without any modification. _ EN 61300-2-38:2006 2 3 EN 61300-2-38:2006 CONTENTS 1 Scope 4 2 Normative references .4 3 General description 4 3.1 Test methods 4 3.2 Apparatus .4 4 Procedure 5 4.1 Method A.5 4.2 Method B.5 5 Severity6 6 Details to be specified 6 Annex Z
17、A (normative) Normative references to international publications with theircorresponding European publications 7 EN 61300-2-38:2006 4 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 2-38: Tests Sealing for pressurized fibre optic closures 1 Scope
18、 This part of IEC 61300 presents a method for testing the sealing performance of a fibre optic closure and sealing system of the closures, when required by the relevant specification. 2 Normative references The following referenced documents are indispensable for the application of this document. Fo
19、r dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61300-1: Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 1: General and guidance 3 G
20、eneral description 3.1 Test methods A number of closures are assembled following the manufacturers instructions. The specimens are then sealed, pressurized and tested for leaks by using the pressure gauge (see 3.2.4) and measuring the time to failure. The tests shall be carried out according to the
21、standard test conditions as defined in IEC 61300-1, unless otherwise specified in the relevant specification. Method A is a performance criterion test for leaks when the specimen is pressurized with air and submerged in a water bath. This method is generally used to check the sealing of the closure
22、after installation or after test. Method B is a performance criterion test for leaks when the specimen is pressurized with air and the pressure loss is monitored by using a gauge. This test method is generally used to check the sealing of the closure during mechanical tests at a specified test tempe
23、rature, by measuring the pressure before and after the test. 3.2 Apparatus The apparatus consists of the following elements. 3.2.1 Cable Suitable cable to assemble the specimen shall be used. 5 EN 61300-2-38:2006 3.2.2 Pressurizer A pressurizer provides means of pressurizing the closures. 3.2.3 Capi
24、llary gas connections Suitable capillary gas connections are needed for fitting into the specimen or cable to allow the specimen to be pressurized. 3.2.4 Pressure gauge A pressure gauge is a gauge to measure the pressure inside the closures. Gauges with a suitable range and a resolution of 0,5 kPa t
25、o determine a 5 % drop in pressure shall be used. 3.2.5 Water bath A water bath is needed for method A. 4 Procedure 4.1 Method A Assemble the specimen using the smallest and the largest cable diameter for which the specimen is designed. Install the pressure gauge into the specimen or cable. Seal the
26、 cable ends at their extremities. Pressurize the closure. Submerge the specimen and cable in a water bath just below the water surface at the required temperature. No escape of air bubbles, indicating a leakage, shall be observed during the test. 4.2 Method B Assemble the specimen using the smallest
27、 and the largest cable diameter for which the specimen is designed. Install the pressure gauge into the specimen or cable. Seal the cable ends at their extremities. Pressurize the closure at specified temperature. With the specimen at the test temperature, the air pressure shall be monitored using t
28、he installed gauge. A record of air pressure versus time shall be kept and plotted. The pressure in the specimen shall not decay more than the specified amount. EN 61300-2-38:2006 6 5 Severity The severity is determined by the initial pressure, the time duration for the test and the allowable leakag
29、e or pressure decay during the test. The following preferred severities may be specified for the sealing procedure. The test overpressure for specimens for unpressurized systems is 40 kPa. The test overpressure for specimens for pressurized systems is 98 kPa. 6 Details to be specified The following
30、details, as applicable, shall be specified in the relevant specification: type and diameter of the cable to be used in the test; the procedure for mounting the specimen; duration of test; method of leak detection (Method A or B); allowable leakage for Method A; allowable pressure decay for Method B;
31、 water head (Method A); pre-conditioning of specimens, if any; deviations from test procedure; additional pass/fail criteria. _ Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable
32、for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod),
33、the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 61300-1 -1)Fibre optic interconnecting devices and passive components - Basic test and measurement procedures Part 1: General and guidance EN 61300-1 20032)1)Undated reference. 2)Valid edition at date of issue. 7 EN 61300-2-38:2006 BS
34、 EN 61300-2-38: 2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBrit
35、ish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity whi
36、le using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscrib
37、ers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI w
38、ebsite at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and
39、international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: info
40、bsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.I
41、nformation regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publication
42、s of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission
43、 from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.
