1、BRITISH STANDARD Resist ance spot welding - Electrode adaptors, male taper 1:lO - Part 2: Parallel shank fixing for end-thrust electrodes The European Standard EN IS0 5183-2:2001 has the status of a British Standard ICs 25.160.30 BS EN IS0 5 183-2:20 O 1 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS P
2、ERMITTED BY COPYRIGHT LAW - BS EN IS0 5183-2:2001 National foreword This British Standard is the official English language version of EN IS0 5183-2:2001. It is identical with IS0 5183-22000. It supersedes BS EN 25183-2:1992 which is withdrawn. The UK participation in its preparation was entrusted to
3、 Technical Committee WEE129, Resistance welding, which has the responsibility to: - - aid enquirers to understand the text; present to the responsible internationallEuropean committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related in
4、ternational and European developments and promulgate them in the UK. - A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be
5、found in the BSI Standards Catalogue under the section entitled “Tnternational Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Stand
6、ards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. This British Standard, having been prepared under the direction of the Engineering Sector Policy and Strategy Committee, was published under the authority
7、 of the Standards Policy and Strategy Committee on 8 November 2001 Q BSI 8 November 2001 Summary of pages This document comprises a front cover, an inside front cover, the EN IS0 title page, EN IS0 foreword page, IS0 title page, pages ii and iii, a blank page, pages i to 4, an inside back cover and
8、a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. IDate I Comments ISBN O 580 38512 4 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IS0 5183-2 October 2001 ICs 25.160.30 Supersedes EN 25183
9、-2:1991 English version Resistance spot welding - Electrode adaptors, male taper 1:lO - Part 2: Parallel shank fixing for end-thrust electrodes (IS0 5183- 2:ZOOO) Equipement de soudage par rsistance - Allonges dlectrode embout amovible, cne mle 1:lO - Partie 2: Emmanchement cylindrique pour pousse e
10、n bout (IS0 5183-2:2000) Widerstandspunktschweien - Elektrodenschfte mit Auenkegel 1:lO - Teil 2: Zylindrische Befestigung fr gerade Beanspruchung (IS0 5183-2:2000) This European Standard was approved by CEN on 4 October 2001. CEN members are bound to comply with the CENICENELEC Internal Regulations
11、 which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Uptedate lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Sta
12、ndard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national stand
13、ards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy. Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITE EUROPEEN DE NORMALISATION EUROPISCHES KOMITEE F
14、UR NORMUNG Management Centre: rue de Stassart, 36 8-1050 Brussels O 2001 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN IS0 5183-2:2001 E EN IS0 5183-2:2001 Foreword The text of the International Standard from Technical Committee
15、ISO/TC 44 “ Welding and allied processes“ of the International Organization for Standardization (EO) has been taken over as an European Standard by Technical Committee CENTTC 121 “Welding“, the secretariat of which is held by DS. This European Standard replaces EN 251 83-2:1991. This European Standa
16、rd shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2002, and conflicting national standards shall be withdrawn at the latest by April 2002. NOTE FROM CMC The foreword is susceptible to be amended on reception of t
17、he German language version. The confirmed or amended foreword, and when appropriate, the normative annex ZA for the references to international publications with their relevant European publications will be circulated with the German version. According to the CENICENELEC Internal Regulations, the na
18、tional standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
19、 Endorsement notice The text of the International Standard IS0 5183-2:2000 has been approved by CEN as a European Standard without any modification. INTERNATIONAL STANDARD EN IS0 6183-2:2001 IS0 51 83-2 Second edition 2000-1 2-01 Resistance spot welding - Electrode adaptors, male taper 1 :IO - Part
20、2: Parallel shank fixing for end-thrust electrodes quipement de soudage par rsistance - Allonges dlectrode embout amovible, cne mle 1:1 O - Partie 2: Emmanchement cylindrique pour pousse en bout Reference number IS0 5183-2:2000(E) EN IS0 5183-2:2001 EN IS0 6183-22001 Foreword IS0 (the International
21、Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been esta
22、blished has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardiza
23、tion. International Standards are drafted in accordance with the rules given in the ISOAEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 %
24、 of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of IS0 51 83 may be the subject of patent rights. IS0 shall not be held responsible for identifying any or all such patent rights. International Standard IS0 51 83-2 was prepared by Tec
25、hnical Committee ISOITC 44, Welding and allied processes, Subcommittee SC 6, Resistance welding. This second edition cancels and replaces the first edition (IS0 5183-2:1988), which has been technically revised. IS0 51 83 consists of the following parts, under the general title Resistance spot weldin
26、g - Electrode adaptors, male taper 1:IO: - Part 1: Conical fixing, taper 1:lO - Part 2: Parallel shank fixing for end thrust electrodes . 111 EN IS0 5183-2:2001 Resistance spot welding - Electrode adaptors, male taper 1 : 10 - Part 2: Parallel shank fixing for end-thrust electrodes 1 Scope This part
27、 of IS0 5183 specifies the dimensions and tolerances of resistance spot welding electrode adaptors where the fixing element for the cap (see IS0 5821) is a male taper of 1:lO and a parallel shaft is used to fix the adaptor to the electrode holder in accordance with IS0 8430-3. 2 Normative references
28、 The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of IS0 5183. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of I
29、S0 5183 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of IS0 and IEC maintain registers of currently valid International
30、Standards. IS0 51 82: 1991, Welding - Materials for resistance welding electrodes and ancillary equipment. IS0 5821: 1979, Resistance spot welding electrode caps. IS0 8430-3: 1988, Resistance spot welding - Electrode holders - Part 3: Parallel shank fixing for end thrust. 3 Dimensions The dimensions
31、 shall be those given in Figure 1 and Table I. 4 Designation The designation of electrode adaptors which comply with this part of IS0 5183 shall include the following: a) the description block (.e. “spot welding electrode adaptor“); b) reference to this part of IS0 5183, .e. IS0 5183-2; c) the type
32、of electrode adaptor, in accordance with Figure 1; d) the diameter, d, in millimetres; e) the length, i, in millimetres; f) the material of which the electrode adaptor is made, in accordance with IS0 5182. 1 EN IS0 5183-2:2001 EXAMPLE shall be designated as follows: A type C spot welding electrode a
33、daptor, of diameter dl = 16 rnm, length I, = 68 mm and material type A 2/1, Spot welding electrode adaptor IS0 5183-2 - C - 16 x 68 - A 211 5 Materiais The material of which the electrode adaptor is made shall be in accordance with IS0 5182:1991, preferably group A, type 2. 6 Marking Electrode adapt
34、ors complying with this part of IS0 5183 shall be marked with the designation laid down in clause 4, but excluding the description block and the reference number of this patt of IS0 5183, e.g.: A - 16 x 68 - A 211 2 EN IS0 6183-2:2001 Dimensions in millimetres Surface roughness values in micrometres
35、 e / l I a) Type C: Straight adaptor with cooling hole open on one side - d I I, t- i b) Type D: Straight adaptor with cooling hole open on both sides IA I J 1 c) Type E: Double cranked adaptor NOTE like type C, or open on both sides, like type D. a Cone diameter at the gauge plane. Figure c) does n
36、ot show the cooling hole. However, the adaptor can be provided with cooling hole open on one side, Over this length the surface shall be neither damaged nor marked. Gauge plane Electrode cap, see IS0 5821. e Electrode holder, see IS0 8430-3. Figure 1 - Electrode adaptors 3 EN IS0 5183-2:2001 Table 1
37、 - Dimensions for adaptors type C, D and E Dimensions in millimetres a Cone diameter at the gauge plane. Values given in parentheses are non-prefened. Value that does not apply to type E. 4 BS EN IS0 5 18 3-2: 200 1 BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institution )SI is
38、the independent national body responsible for preparing Iritish Standards. It presents the UK view on standards in Europe and at the nternational level. It is incorporated by Royal Charter. tevsions ritish Standards are updated by amendment or revision. Users of 3ritish Standards should make sure th
39、at they possess the latest amendments or bditions. t is the constant aim of BSI to improve the quality of our products and services. Ve would be grateful if anyone finding an inaccuracy or ambiguity while using his British Standard would inform the Secretary of the technical committee esponsible, th
40、e identity of which can be found on the inside front cover. Lel: 020 8996 9000. Fax: 020 8996 7400. 3SI offers members an individual updating service called PLUS which ensures hat subscribers automatically receive the latest editions of standards. 3uying standards hders for all BSI, international an
41、d foreign standards publications should be iddressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. jtandards are also available from the BSI website at tt:/.bsi-. n response to orders for international standards, it is BSI policy to supply the 3SI implementation of those that have be
42、en published as British Standards, inless otherwise requested. nformation on standards BSI provides a wide range of information on national, European and nternational standards through its Library and its Technical Help tr, Exporters jervice. Various BSI electronic information services are also avai
43、lable which give ietails on all its products and services. Contact the Information Centre. iel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details ,f these and
44、 other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is 3vailable on the BSI website at &td/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internat
45、ional standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. Th
46、is does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: O20 8996 7070.
