1、BS EN ISO 6134:2017Rubber hoses and hoseassemblies for saturated steam Specification (ISO 6134:2017)BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN ISO 6134:2017 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 6134:2017
2、. It supersedes BS EN ISO 6134:2005 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/66, Rubber and plastics tubing, hoses and hoseassemblies.A list of organizations represented on this committee can beobtained on request to its secretary.This public
3、ation does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2017. Published by BSI Standards Limited 2017ISBN 978 0 580 85119 3ICS 23.040.70Compliance with a British Standard cannot confer immunity f
4、romlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 January 2017.Amendments/Corrigenda issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 6134 January 2017 ICS 23.040.70 Super
5、sedes EN ISO 6134:2005English Version Rubber hoses and hose assemblies for saturated steam - Specification (ISO 6134:2017) Tuyaux et flexibles en caoutchouc pour vapeur sature - Spcification (ISO 6134:2017) Gummischluche und -schlauchleitungen fr gesttigten Dampf - Spezifikation (ISO 6134:2017) This
6、 European Standard was approved by CEN on 30 November 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical refere
7、nces concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN
8、member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
9、 France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION E
10、UROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 6134:2017 EBS EN ISO 6134:2017EN ISO 6134:2017 (E) 3 European foreword This doc
11、ument (EN ISO 6134:2017) has been prepared by Technical Committee ISO/TC 45 “Rubber and rubber products“ in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies” the secretariat of which is held by BSI. This European Standard shall be given the status of a
12、 national standard, either by publication of an identical text or by endorsement, at the latest by July 2017 and conflicting national standards shall be withdrawn at the latest by July 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
13、 rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 6134:2005. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European
14、Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia,
15、Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 6134:2017 has been approved by CEN as EN ISO 6134:2017 without any modification. BS EN ISO 6134:2017ISO 6134:2017(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Gener
16、al requirements . 25 Classification 26 Materials and construction . 27 Dimensions and tolerances . 27.1 Diameters, thickness of lining and cover, and bend radii . 27.2 Length of hoses and hose assemblies and tolerances . 37.3 Concentricity. 38 Physical properties of compounds 39 Physical properties
17、of finished hoses and hose assemblies 410 Resistance to steam . 510.1 Principle 510.2 Short-term exposure 510.3 Long term test 510.4 Observations . 510.5 Additional tests . 511 Electrical resistance 512 Type testing 613 Marking 613.1 Hoses . 613.2 Hose couplings 713.3 Identification of hose assembli
18、es 714 Frequency of testing 7Annex A (informative) Test frequency for hose assemblies in use . 8Annex B (informative) Storage and admissible storage time . 9Annex C (normative) Type and routine test .10Annex D (informative) Test frequency for production acceptance test 11Bibliography .12 ISO 2017 Al
19、l rights reserved iiiContents PageBS EN ISO 6134:2017ISO 6134:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technica
20、l committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely wit
21、h the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed f
22、or the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent ri
23、ghts. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in
24、 this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principl
25、es in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Rubber and plastics hoses and hose assemblies.This fourth edition cancels and replaces the
26、 third edition (ISO 6134:2005), which has been technically revised to update Clause 2.iv ISO 2017 All rights reservedBS EN ISO 6134:2017INTERNATIONAL STANDARD ISO 6134:2017(E)Rubber hoses and hose assemblies for saturated steam Specification1 ScopeThis document specifies requirements for two types o
27、f hoses and hose assemblies, low pressure with a maximum working pressure of 6 bar and high pressure with a maximum working pressure of 18 bar, made of rubber and hose fittings made of metal, designed to convey saturated steam and hot water condensate.Each type is divided into two classes having eit
28、her an oil resistant or non-oil resistant cover.NOTE Information on the frequency of testing of hose assemblies in use and storage is given in Annex A and Annex B.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes req
29、uirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 37, Rubber, vulcanized or thermoplastic Determination of tensile stress-strain propertiesISO 188, Rubber, vul
30、canized or thermoplastic Accelerated ageing and heat resistance testsISO 1402, Rubber and plastics hoses and hose assemblies Hydrostatic testingISO 1817, Rubber, vulcanized or thermoplastic Determination of the effect of liquidsISO 4023:2009, Rubber hoses and hose assemblies for steam Test methodsIS
31、O 4649:2010, Rubber, vulcanized or thermoplastic Determination of abrasion resistance using a rotating cylindrical drum deviceISO 4671, Rubber and plastics hoses and hose assemblies Methods of measurement of the dimensions of hoses and the lengths of hose assembliesISO 7326:2006, Rubber and plastics
32、 hoses Assessment of ozone resistance under static conditionsISO 8031:2009, Rubber and plastics hoses and hose assemblies Determination of electrical resistance and conductivityISO 8033, Rubber and plastics hoses Determination of adhesion between componentsISO 8330, Rubber and plastics hoses and hos
33、e assemblies VocabularyISO 10619-1:2011, Rubber and plastics hoses and tubing Measurement of flexibility and stiffness Part 1: Bending tests at ambient temperature3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 8330 apply.ISO and IEC maintain terminol
34、ogical databases for use in standardization at the following addresses: IEC Electropedia: available at h t t p :/ www .electropedia .org/ ISO 2017 All rights reserved 1BS EN ISO 6134:2017ISO 6134:2017(E) ISO Online browsing platform: available at h t t p :/ www .iso .org/ obp4 General requirementsQu
35、ick-release coupling shall not be used under any circumstances.The end fittings used with the hose shall be of a type that provides for tightening-up during service; for example, a clamp type to compensate for creep of the rubber compounds in the hose.NOTE 1 Where superheated steam conditions occur,
36、 the service life of the product can be reduced.NOTE 2 Vacuum caused by shutting off the hose assembly at both ends can precipitate “pop-corning” or separation of the lining.5 ClassificationThis document specifies two types of hoses/hose assemblies to convey saturated steam and hot water condensate.
37、Type 1: low-pressure steam hose, maximum working pressure 6 bar, corresponding to a temperature of 164 C.Type 2: high pressure steam hose, maximum working pressure 18 bar, corresponding to a temperature of 210 C.NOTE 1 bar = 0,1 MPa.Each type of hose is divided into either of the following: Class A:
38、 a non-oil-resistant cover; Class B: an oil-resistant cover.Both types and classes can be either of the following:a) electrically bonded, marked “M” (see Clause 11);b) electrically conductive, marked “” (see Clause 11).6 Materials and constructionHoses shall consist of a lining which is resistant to
39、 steam and hot water condensate and shall be uniform in quality, free of porosity, air holes, foreign inclusions and other defects.The reinforcement shall be textile for Type 1 and steel wire for Type 2, either braided, spiral or cord ply construction.The cover shall give protection against mechanic
40、al damage and be resistant to heat, wear and environmental effects due to weather and short-term chemical exposure. It shall be pricked equally around the periphery and along the whole length of the hose in order to relieve any pressure built-up between the plies and the cover.7 Dimensions and toler
41、ances7.1 Diameters, thickness of lining and cover, and bend radiiWhen determined in accordance with ISO 4671, the diameters, thickness of lining and cover, and the bend radii of the hoses shall conform to the values given in Table 1.2 ISO 2017 All rights reservedBS EN ISO 6134:2017ISO 6134:2017(E)Ta
42、ble 1 Diameters, thickness and bend radiiDimensions in millimetresInternal diameter Outside diameter Thickness min. Bend radius min.Deviation limitsDeviation limitsLining Cover9,5 0,5 21,5 1,0 2,0 1,5 12013 0,5 25 1,0 2,5 1,5 13016 0,5 30 1,0 2,5 1,5 16019 0,5 33 1,0 2,5 1,5 19025 0,5 40 1,0 2,5 1,5
43、 25032 0,5 48 1,0 2,5 1,5 32038 0,5 54 1,2 2,5 1,5 38045 0,7 61 1,2 2,5 1,5 45050 0,7 68 1,4 2,5 1,5 50051 0,7 69 1,4 2,5 1,5 50063 0,8 81 1,6 2,5 1,5 63075 0,8 93 1,6 2,5 1,5 75076 0,8 94 1,6 2,5 1,5 750100 0,8 120 1,6 2,5 1,5 1 000102 0,8 122 1,6 2,5 1,5 1 0007.2 Length of hoses and hose assemblie
44、s and tolerancesThe length of the hose assembly is the overall measured distance from the sealing surfaces of the couplings from end to end.The deviation limits of the hoses and hose assemblies shall be as follows: l 1 000 mm: 10 mm; l 1 000 mm: 1 %.7.3 ConcentricityWhen determined in accordance wit
45、h ISO 4671, the concentricity of the hose wall shall not exceed 1,0 mm for internal diameter hoses up to and including 51 mm and 1,5 mm for sizes above.8 Physical properties of compoundsTests shall be carried out on test sheets of 2,0 mm minimum thickness of equivalent cure to that of the hoses.The
46、physical properties of compounds shall conform to the values given in Table 2.The recommended frequency of testing is illustrated in Table D.1. ISO 2017 All rights reserved 3BS EN ISO 6134:2017ISO 6134:2017(E)Table 2 Physical properties of compoundsProperty Unit Requirements Method of testLining Cov
47、erTensile strength, min. MPa 8 8 ISO 37 (dumb-bell test piece)Elongation at break, min. % 200 200 ISO 37 (dumb-bell test piece)Ageing tensile strength change, max. elongation at break change, max.%50505050ISO 188 (7 days at 125 C for Type 1 and 150 C for Type 2, air oven method)Abrasion resistance b
48、lack filled compound, max. non-black filled compound, max. colouredmm3mm3200400ISO 4649:2010, method AChange in volume, max. (class B only) % 100 ISO 1817, oil No. 3, 72 h at 100 C9 Physical properties of finished hoses and hose assembliesThe physical properties of finished hoses and hose assemblies
49、 shall conform to the values given in Table 3.The minimum frequency of testing shall be in accordance with Clause 14.Table 3 Physical properties of finished hoses and hose assembliesProperty Unit Requirements Method of testHosesBurst pressure, min. 10 the max. working pressure ISO 1402Proof test pressureNo leakage or distortion at 5 the max. working pressureISO 1402Adhesion between components, min.kN/m 2,4 ISO 8033Bending test, (under no pres-sure), min.T/D 0,8 IS
