1、BRITISH STANDARDBS EN ISO 8751:2007Spring-type straight pins Coiled, light dutyThe European Standard EN ISO 8751:2007 has the status of a British StandardICS 21.060.50g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g5
2、3g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN ISO 8751:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2007 BSI 2007ISBN 978 0 580 55834 4National forewordThis British Standard is the UK implementation
3、 of EN ISO 8751:2007. It supersedes BS EN ISO 8751:1998 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee FME/9, Nuts, bolts and accessories/steering committee.A list of organizations represented on this committee can be obtained on request to its secret
4、ary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNO
5、RME EUROPENNEEUROPISCHE NORMEN ISO 8751April 2007ICS 21.060.50 Supersedes EN ISO 8751:1997 English VersionSpring-type straight pins - Coiled, light duty (ISO 8751:2007)Goupilles lastiques spirales - Srie mince (ISO8751:2007)Spiralspannstifte - Leichte Ausfhrung (ISO 8751:2007)This European Standard
6、was approved by CEN on 22 March 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nat
7、ionalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and no
8、tified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Mal
9、ta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploit
10、ation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 8751:2007: EForeword This document (EN ISO 8751:2007) has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in collaboration with Technical Committee CEN/TC 185 “Fasteners”, the secretariat of which
11、 is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2007, and conflicting national standards shall be withdrawn at the latest by October 2007. This document supersedes EN ISO
12、8751:1997. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Irela
13、nd, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Endorsement notice The text of ISO 8751:2007 has been approved by CEN as EN ISO 8751:2007 without any modifications. EN ISO 8751:2007Ref
14、erence numberISO 8751:2007(E)INTERNATIONAL STANDARD ISO8751Third edition2007-04-15Spring-type straight pins Coiled, light duty Goupilles lastiques spirales Srie mince EN ISO 8751:2007ii iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standar
15、ds bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organi
16、zations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in
17、 the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 %
18、of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 8751 was prepared by Technical Committee ISO/TC 2, Fasteners
19、, Subcommittee SC 10, Product standards for fasteners. This third edition cancels and replaces the second edition (ISO 8751:1997), which has been technically revised. EN ISO 8751:2007blank1Spring-type straight pins Coiled, light duty 1 Scope This International Standard specifies the characteristics
20、of coiled light duty spring-type straight pins made of steel or of austenitic or martensitic stainless steel, with a nominal diameter, d1, from 1,5 mm to 8 mm inclusive. NOTE Spring-type straight pins, coiled, heavy duty, and spring type straight pins, coiled, standard duty, are the subjects of ISO
21、8748 and ISO 8750, respectively. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) ap
22、plies. ISO 286-2, ISO system of limits and fits Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts ISO 3269, Fasteners Acceptance inspection ISO 4042, Fasteners Electroplated coatings ISO 6507-1, Metallic materials Vickers hardness test Part 1: Test method ISO 8749
23、, Pins and grooved pins Shear test 3 Dimensions See Figure 1 and Table 1. aSwaged chamfer at both ends. Figure 1 EN ISO 8751:20072 Table 1 Dimensions Dimensions in millimetres nom. 1,5 2 2,5 3 3,5 4 5 6 8 max. 1,75 2,28 2,82 3,35 3,87 4,45 5,5 6,55 8,65 d1before mounting min. 1,62 2,13 2,65 3,15 3,6
24、7 4,20 5,2 6,25 8,30 d2before mounting max. 1,4 1,9 2,4 2,9 3,4 3,9 4,85 5,85 7,8 a 0,5 0,7 0,7 0,9 1 1,1 1,3 1,5 2 s 0,08 0,11 0,14 0,17 0,19 0,22 0,28 0,33 0,45 a 0,8 1,5 2,3 3,3 4,5 5,7 9 13 23 Minimum shear strength, double, kN b 0,65 1,1 1,8 2,5 3,4 4,4 7 10 18 l cnom. min. max. 4 3,75 4,25 5 4
25、,75 5,25 6 5,75 6,25 8 7,75 8,25 10 9,75 10,25 12 11,5 12,5 14 13,5 14,5 16 15,5 16,5 Range 18 17,5 18,5 20 19,5 20,5 22 21,5 22,5 of 24 23,5 24,5 26 25,5 26,5 28 27,5 28,5 commercial 30 29,5 30,5 32 31,5 32,5 35 34,5 35,5 lengths 40 39,5 40,5 45 44,5 45,5 50 49,5 50,5 55 54,25 55,75 60 59,25 60,75
26、65 64,25 65,75 70 69,25 70,75 75 74,25 75,75 80 79,25 80,75 85 84,25 85,75 90 89,25 90,75 95 94,25 95,75 100 99,25 100,75 120 119,25 120,75 aApplies to steel and martensitic corrosion resistant steel products. bApplies to austenitic stainless steel products. cFor nominal lengths above 120 mm, steps
27、of 20 mm. EN ISO 8751:200734 Application The diameter of the hole into which the spring pin is to be inserted shall be equal to the nominal diameter, d1, of the mating pin and to tolerance class H12 in accordance with ISO 286-2. 5 Requirements and reference International Standards See Table 2. Table
28、 2 Requirements and reference International Standards Steel Austenitic stainless steel Martensitic stainless steel St A C All pin diameters Alternative for pin diameters d1 12 mm Chemical composition limits (chemical analysis) % Chemical composition limits (chemical analysis) % C W 0,64 Mn W 0,60 Si
29、 W 0,15 CrbP u 0,04 S u 0,05 C W 0,38 Mn W 0,70 Si W 0,20 Cr W 0,80 V W 0,15 P u 0,035 S u 0,04 C u 0,15 Mn u 2,00 Si u 1,50 Cr 16 to 20 Ni 6 to 12 P u 0,045 S u 0,03 Mo u 0,8 C W 0,15 Mn u 1,00 Si u 1,00 Cr 11,5 to 14 Ni u 1,00 P u 0,04 S u 0,03 Hardened and tempered to a Vickers hardness of 420 HV
30、 to 545 HV Cold worked Hardened and tempered to a Vickers hardness of 460 HV to 560 HV MaterialaHardness testing according to ISO 6507-1. Hardness testing according to ISO 6507-1. Plain, i.e. pins to be supplied in natural finish, treated with a protective lubricant, unless otherwise specified by ag
31、reement between customer and supplier. If pins are surface coated, appropriate plating or coating processes should be employed to avoid hydrogen embrittlement. Due to the risk of hydrogen embrittlement, pins should not be electroplated or phosphate-coated. If electroplating or phosphate coating is r
32、equired for corrosion prevention, by agreement between customer and supplier, it is mandatory that the pins be baked immediately after plating to minimize the risk of hydrogen embrittlement, see also hydrogen embrittlement relief according to ISO 4042. Nevertheless, freedom from hydrogen embrittleme
33、nt is not absolutely guaranteed. Surface finish All tolerances shall apply prior to the application of a plating or coating. Plain, i.e. pins to supplied in natural finish. Workmanship Pins shall be uniform in quality and free of irregularities or detrimental defects. No burrs shall appear on any pa
34、rt of the pin. Shear strength test The test shall be in accordance with ISO 8749. Acceptability The acceptance procedure shall be in accordance with ISO 3269. aOther materials as agreed between customer and supplier. bUse of Cr is optional. EN ISO 8751:20074 6 Designation EXAMPLE 1 A spring-type str
35、aight pin, coiled, light duty, with nominal diameter d1= 6 mm and nominal length l = 30 mm, made of steel (St) is designated as follows: Spring pin ISO 8751 - 6 30 - St EXAMPLE 2 A spring-type straight pin, coiled, light duty, with nominal diameter d1= 6 mm and nominal length l = 30 mm, made of aust
36、enitic stainless steel (A) is designated as follows: Spring pin ISO 8751 - 6 30 - A EN ISO 8751:20075Bibliography 1 ISO 8748, Spring-type straight pins Coiled, heavy duty 2 ISO 8750, Spring-type straight pins Coiled, standard duty EN ISO 8751:2007BS EN ISO 8751:2007BSI389 Chiswick High RoadLondonW4
37、4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Us
38、ers of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secret
39、ary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of stand
40、ards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for int
41、ernational standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Te
42、chnical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date wi
43、th standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standard
44、s via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except
45、as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the
46、course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.
