1、 ETSI EN 300 219 V2.1.1 (2016-08) Land Mobile Service; Radio equipment transmitting signals to initiate a specific response in the receiver; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU HARMONISED EUROPEAN STANDARD ETSI ETSI EN 300 219 V2.1.1 (20
2、16-08) 2 Reference REN/ERM-TGDMR-349 Keywords analogue, mobile, PMR, radio, signalling ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de
3、 Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modifie
4、d without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. User
5、s of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send
6、your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission o
7、f ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI
8、logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 300 219 V2.
9、1.1 (2016-08) 3 Contents Intellectual Property Rights 7g3Foreword . 7g3Modal verbs terminology 7g31 Scope 8g32 References 8g32.1 Normative references . 8g32.2 Informative references 9g33 Definitions, symbols and abbreviations . 10g33.1 Definitions 10g33.2 Symbols 10g33.3 Abbreviations . 10g34 Speech
10、 equipment with signalling 11g34.1 Applicability . 11g34.1.1 General 11g34.1.2 Equipment with speech and signalling functions 11g34.1.3 Equipment with an add-on signalling unit 11g35 General and operational requirements 12g35.1 General . 12g35.1.1 Environmental profile . 12g35.1.2 Choice of model fo
11、r testing 12g35.2 Mechanical and electrical design 12g35.2.1 General 12g35.2.2 Controls 12g35.2.3 Transmitter shut-off facility (time-out) . 12g36 Test conditions, power sources and ambient temperatures 12g36.1 Normal and extreme test conditions . 12g36.2 Test power source . 12g36.3 Normal test cond
12、itions 13g36.3.1 Normal temperature and humidity 13g36.3.2 Normal test power source . 13g36.3.2.1 Mains voltage 13g36.3.2.2 Regulated lead-acid battery power sources used on vehicles 13g36.3.2.3 Other power sources 13g36.4 Extreme test conditions 13g36.4.1 Extreme temperatures . 13g36.4.2 Extreme te
13、st source voltages . 14g36.4.2.1 Mains voltage 14g36.4.2.2 Regulated lead-acid battery power sources used on vehicles 14g36.4.2.3 Power sources using other types of batteries . 14g36.4.2.4 Other power sources 14g36.5 Procedure for tests at extreme temperatures . 14g36.5.0 Thermal balance 14g36.5.1 P
14、rocedure for equipment designed for continuous transmission. 15g36.5.2 Procedure for equipment designed for intermittent transmission . 15g37 General conditions of measurement . 15g37.1 Arrangements for test signals at the input of the receiver 15g37.2 Receiver mute or squelch facility . 15g37.3 Nor
15、mal test signals, (wanted and unwanted signals) 15g37.4 Encoder for receiver measurements . 16g37.5 Test Load (artificial antenna) . 16g37.6 Test sites and general arrangements for radiated measurements 16g37.7 Transmitter automatic shut-off facility (time-out) 16g3ETSI ETSI EN 300 219 V2.1.1 (2016-
16、08) 4 7.8 Modes of operation of the transmitter 16g37.9 Facilities for access between the receiver demodulator output and its decoder . 16g37.10 Calling indicator . 17g37.11 Reset . 17g37.12 Reset time . 17g37.13 Test of equipment with a duplex filter 17g38 Technical characteristic of the transmitte
17、r . 17g38.1 Frequency error 17g38.1.0 Applicability . 17g38.1.1 Definition 17g38.1.2 Method of measurement . 17g38.1.3 Limits 18g38.2 Carrier power (conducted) 18g38.2.0 Applicability . 18g38.2.1 Definitions 18g38.2.2 Method of measurement . 19g38.2.3 Limits 19g38.3 Effective radiated power (field s
18、trength) 19g38.3.0 Applicability . 19g38.3.1 Definition 19g38.3.2 Method of measurement . 19g38.3.3 Limits 21g38.4 Adjacent and alternate channel power 22g38.4.0 Applicability . 22g38.4.1 Definition 22g38.4.2 Method of measurement . 22g38.4.3 Limits 24g38.5 Transmitter spurious emissions 24g38.5.0 A
19、pplicability . 24g38.5.1 Definition 24g38.5.2 Method of measuring the power level 24g38.5.3 Method of measuring the effective radiated power . 25g38.5.4 Transmitter spurious emissions . 26g38.6 Intermodulation attenuation 27g38.6.0 Applicability . 27g38.6.1 Definition 27g38.6.2 Method of measurement
20、 . 28g38.6.3 Limits 29g38.7 Transmitter Attack Time 29g38.7.0 Applicability . 29g38.7.1 Definition 29g38.7.2 Method of measurement . 29g38.7.3 Limits 30g38.8 Transmitter release time . 30g38.8.0 Applicability . 30g38.8.1 Definition 30g38.8.2 Method of measurement . 30g38.8.3 Limits 31g38.9 Transient
21、 frequency behaviour of the transmitter . 31g38.9.0 Applicability . 31g38.9.1 Definitions 31g38.9.2 Method of measurement . 31g38.9.3 Limits 35g39 Technical characteristics of the receiver 35g39.1 Reference sensitivity (responses) . 35g39.1.1 Definition 35g39.1.2 Reference sensitivity (response) . 3
22、5g39.2 Maximum usable sensitivity (responses, conducted) . 35g39.2.0 Applicability . 35g39.2.1 Definition 35g3ETSI ETSI EN 300 219 V2.1.1 (2016-08) 5 9.2.2 Method of measurement (“up-down method“) . 36g39.2.3 Limits 36g39.3 Average usable sensitivity (field strength, responses) 36g39.3.0 Applicabili
23、ty . 36g39.3.1 Definition 37g39.3.2 Method of measurement under normal test conditions . 37g39.3.3 Method of measurement of the average usable sensitivities under extreme test conditions . 38g39.3.4 References for degradation measurements . 39g39.3.4.1 Definition. 39g39.3.4.2 Procedures for measurem
24、ents using the test fixture 39g39.3.4.3 Procedures for measurements using the test site . 40g39.3.5 Limits 40g39.4 Co-channel rejection. 41g39.4.0 Applicability . 41g39.4.1 Definition 41g39.4.2 Method of measurement . 41g39.4.3 Limits 42g39.5 Adjacent channel selectivity . 42g39.5.0 Applicability .
25、42g39.5.1 Definition 42g39.5.2 Method of measurement . 43g39.5.3 Limits 44g39.6 Spurious response rejection 44g39.6.0 Applicability . 44g39.6.1 Definition 44g39.6.2 Introduction to the method of measurement . 44g39.6.3 Method of search over the “limited frequency range“ 45g39.6.4 Method of measureme
26、nt . 46g39.6.5 Limits 47g39.7 Intermodulation response . 47g39.7.0 Applicability . 47g39.7.1 Definition 47g39.7.2 Method of measurement . 47g39.7.3 Limits 48g39.8 Blocking or desensitization 48g39.8.0 Applicability . 48g39.8.1 Definition 48g39.8.2 Method of measurement . 49g39.8.3 Limits 50g39.9 Rec
27、eiver spurious radiations. 50g39.9.0 Applicability . 50g39.9.1 Definition 50g39.9.2 Method of measuring the power level 50g39.9.3 Method of measuring the effective radiated power . 51g39.9.4 Limits 52g310 Duplex operation 52g310.0 Applicability . 52g310.1 Receiver desensitization (with simultaneous
28、transmission and reception) . 52g310.1.1 Definition 52g310.1.2 Method of measurement when the equipment operates with a duplex filter . 53g310.1.3 Method of measurement when the equipment operates with separate Tx and Rx antennas . 54g310.1.4 Limits 54g310.2 Receiver spurious response rejection (wit
29、h simultaneous transmission and reception) . 55g310.2.1 Definition 55g310.2.2 Method of measurement . 55g310.2.3 Limits 56g311 Testing for compliance with technical requirements 56g311.1 Test conditions, power supply and ambient temperatures 56g311.2 Interpretation of the measurement results 56g3Ann
30、ex A (normative): Radiated measurement 58g3ETSI ETSI EN 300 219 V2.1.1 (2016-08) 6 A.1 Test sites and general arrangements for measurements involving the use of radiated fields . 58g3A.1.0 General . 58g3A.1.1 Anechoic chamber 58g3A.1.2 Anechoic chamber with a conductive ground plane . 59g3A.1.3 Open
31、 Area Test Site (OATS) . 60g3A.1.4 Test antenna 61g3A.1.5 Substitution antenna . 61g3A.1.6 Measuring antenna . 62g3A.2 Guidance on the use of radiation test sites . 62g3A.2.0 General . 62g3A.2.1 Verification of the test site . 62g3A.2.2 Preparation of the EUT . 62g3A.2.3 Power supplies to the EUT .
32、62g3A.2.4 Volume control setting for analogue speech tests 62g3A.2.5 Range length . 63g3A.2.6 Site preparation 63g3A.3 Coupling of signals . 64g3A.3.1 General . 64g3A.3.2 Data signals 64g3A.3.3 Speech and analogue signals 64g3A.3.3.0 General 64g3A.3.3.1 Acoustic coupler description. 64g3A.3.3.2 Cali
33、bration 65g3A.4 Test fixture . 65g3A.4.1 Description 65g3A.4.2 Calibration 65g3A.4.3 Mode of use 66g3Annex B (normative): Specification for some particular measurement arrangements . 67g3B.1 Power measuring receiver specification . 67g3B.1.0 General . 67g3B.1.1 IF filter . 67g3B.1.2 Attenuation indi
34、cator 69g3B.1.3 RMS value indicator . 69g3B.1.4 Oscillator and amplifier 69g3B.2 Spectrum analyser specification . 69g3B.2.1 Adjacent and alternate channel power measurement 69g3B.2.2 Unwanted emissions measurement . 70g3B.3 Integrating and power summing device . 70g3Annex C (normative): Relationshi
35、p between the present document and the essential requirements of Directive 2014/53/EU . 71g3History 73g3ETSI ETSI EN 300 219 V2.1.1 (2016-08) 7 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to t
36、hese essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Late
37、st updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI W
38、eb server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commission
39、s standardisation request C(2015) 5376 final i.7 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/E
40、C i.5. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table C.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresp
41、onding essential requirements of that Directive, and associated EFTA regulations. National transposition dates Date of adoption of this EN: 21 March 2016 Date of latest announcement of this EN (doa): 30 June 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
42、31 December 2016 Date of withdrawal of any conflicting National Standard (dow): 31 December 2017 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of
43、 the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 300 219 V2.1.1 (2016-08) 8 1 Scope The present document applies to constant envelope angle modulation systems for use
44、 in the land mobile service, using the available bandwidth, operating on radio frequencies between 30 MHz and 1 GHz, with channel separations of 12,5 kHz, 20 kHz and 25 kHz intended for transmission and/or reception of signals used to initiate a specific response in the receiver. Table 1: Radiocommu
45、nications service frequency bands Radiocommunications service frequency bands Transmit 30 MHz to 1 000 MHz Receive 30 MHz to 1 000 MHz The present document applies to non-speech and to the non-speech part of combined speech/non-speech analogue equipment. In the present document, non-speech radio equ
46、ipment is defined as a radio equipment transmitting a signal to initiate a specific response in the receiver. The equipment shall comprise a transmitter and associated encoder and/or a receiver and associated decoder. The encoder and/or decoder may be a separate piece of equipment, in which case com
47、pliance to the present document covers the encoder and/or decoder in connection with the transmitter and/or receiver equipment. In the present document different requirements are given for the different radio frequency bands, channel separations, environmental conditions and types of equipment, wher
48、e appropriate. The types of equipment covered by the present document are as follows: Base Station: equipment fitted with an antenna socket; Mobile Station: equipment fitted with an antenna socket; Handportable stations: a) fitted with an antenna socket; or b) without an external antenna socket (int
49、egral antenna equipment) but fitted with a permanent internal or a temporary internal 50 Radio Frequency (RF) connector which allows access to the transmitter output and the receiver input. Handportable equipment without an external or internal RF connector and without the possibility of having a temporary internal 50 RF connector is not covered by the present document. Integral antenna equipment is covered by ETSI EN 300 341 i.1 (see the corresponding scope). The present document contains requirements to demonstrate that “. Radio equipment shall be so constru
