1、 ETSI EN 301 843-6 V2.1.1 (2016-03) ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services; Harmonised Standard covering the essential requirements of article 3.1b of the Directive 2014/53/EU; Part 6: Specific conditions for Earth Stations on board Vessels operating in
2、frequency bands above 3 GHz HARMONISED EUROPEAN STANDARD ETSI ETSI EN 301 843-6 V2.1.1 (2016-03) 2 Reference REN/ERM-EMC-351 Keywords EMC, harmonised standard, maritime, radio ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 3
3、48 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The con
4、tent of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Doc
5、ument Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.o
6、rg/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mech
7、anical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunication
8、s Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM l
9、ogo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 301 843-6 V2.1.1 (2016-03) 3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 6g33 Definitions, symbols a
10、nd abbreviations . 7g33.1 Definitions 7g33.2 Symbols 7g33.3 Abbreviations . 8g34 General and operational requirements 8g34.1 Environmental profile . 8g34.2 Arrangements for test signals . 8g34.2.0 General 8g34.2.1 Arrangements for test signals at the input of the transmitter 8g34.2.2 Arrangements fo
11、r test signals at the output of the transmitter 9g34.2.3 Arrangements for test signals at the input of the receiver . 9g34.2.4 Arrangements for test signals at the output of the receiver . 9g34.2.5 Arrangements for testing transmitter and receiver together (as a system) 9g34.3 Exclusion bands 9g34.4
12、 Narrow band responses of receivers . 9g34.5 Normal test modulation 9g35 Performance assessment . 9g35.1 General . 9g35.2 Equipment which can provide a continuous communication link 9g35.3 Equipment which does not provide a continuous communication link 10g35.4 Ancillary equipment . 10g35.5 Equipmen
13、t classification 10g35.6 Equipment configuration(s) 10g36 Performance criteria . 11g36.0 Performance criteria grades 11g36.1 Performance criteria A for continuous phenomena applied to transmitters and receivers 11g36.2 Performance criteria B for transient phenomena applied to transmitters and receiv
14、ers . 12g36.2.1 Performance criteria (BA) for transient phenomena applied to a grade A EUT 12g36.2.2 Performance criteria (BB) for transient phenomena applied to a grade B EUT 12g36.3 Performance criteria C applied to power supply failure . 13g36.4 Performance check . 13g36.5 Performance criteria fo
15、r equipment which does not provide a continuous communication link 13g36.6 Performance criteria for ancillary equipment tested on a stand alone basis . 13g37 Applicability overview . 13g37.1 Emission . 13g37.1.1 General 13g37.1.2 Special conditions . 13g37.2 Immunity 14g37.2.1 General 14g37.2.2 Spec
16、ial conditions . 14g3Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 15g3Annex B (informative): Examples of earth stations on board vessels in the scope of the present document . 16g3ETSI ETSI EN 301 843-6 V2.1.1 (2016-03) 4 B.0
17、 Definitions of Earth Stations on board Vessels equipment within the scope of the present document 16g3B.1 Earth Stations on board Vessels operating in the 11 GHz, 12 GHz and 14 GHz frequency bands allocated to the Fixed Satellite Service (FSS) 16g3B.2 Earth Stations on board Vessels operating in th
18、e 6/4 GHz frequency bands allocated to the Fixed Satellite Service (FSS) 16g3History 18g3ETSI ETSI EN 301 843-6 V2.1.1 (2016-03) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essentia
19、l IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates ar
20、e available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) wh
21、ich are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commissions standardisa
22、tion request C(2015) 5376 final i.3 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.1. Once t
23、he present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 of ETSI EN 301 843-1 1 confers, within the limits of the scope of the present document, a presumption of conformity with t
24、he corresponding essential requirements of that Directive, and associated EFTA regulations. The present document is part 6 of a multi-part deliverable. Full details of the entire series can be found in part 1 1. National transposition dates Date of adoption of this EN: 21 March 2016 Date of latest a
25、nnouncement of this EN (doa): 30 June 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 December 2016 Date of withdrawal of any conflicting National Standard (dow): 31 December 2017 Modal verbs terminology In the present document “shall“, “shall not“, “sh
26、ould“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation.
27、ETSI ETSI EN 301 843-6 V2.1.1 (2016-03) 6 1 Scope The present document together with ETSI EN 301 843-1 1, covers the assessment of Earth Stations on board Vessels (ESVs) transmitting above 3 GHz in the Fixed Satellite Service (FSS) as defined in annex B and ancillary equipment in respect of ElectroM
28、agnetic Compatibility (EMC). Technical specifications related to the antenna port and emissions from the enclosure port of Earth Stations on board Vessels are not included in the present document. Such technical specifications are found in the related product standards for the effective use of the r
29、adio spectrum. The present document specifies the applicable test conditions, performance assessment, and performance criteria for Earth Stations on board Vessels and the associated ancillary equipment. In case of differences (for instance concerning special conditions, definitions, abbreviations) b
30、etween the present document and ETSI EN 301 843-1 1, the provisions of the present document take precedence. The electromagnetic environment used in the present document to develop the technical specifications encompasses the electromagnetic environment onboard ships as identified in CENELEC EN 6094
31、5 i.2. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document
32、 (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their lon
33、g term validity. The following referenced documents are necessary for the application of the present document. 1 ETSI EN 301 843-1 (V2.1.1) (03-2016): “ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services; Harmonised Standard covering the essential requirements of art
34、icle 3.1b of the Directive 2014/53/EU; Part 1: Common technical requirements“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-speci
35、fic references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the app
36、lication of the present document but they assist the user with regard to a particular subject area. i.1 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio eq
37、uipment and repealing Directive 1999/5/EC. i.2 CENELEC EN 60945 (2002-10-01) + Corrigendum 1 (2008): “Maritime navigation and radiocommunication equipment and systems - General requirements - Methods of testing and required test results“. ETSI ETSI EN 301 843-6 V2.1.1 (2016-03) 7 i.3 Commission Impl
38、ementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the
39、Council. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ETSI EN 301 843-1 1 and the following apply: above-deck unit: part of the ESV intended to be installed above deck, as declared by the manufacturer, or as ind
40、icated in the user documentation NOTE 1: The above-deck unit usually comprises the following main parts: a) the antenna sub-system which converts the incident radiation field into a guided wave and vice versa; b) the Low Noise Block (LNB) down converter, which is a device that amplifies, with very l
41、ow internal noise, the received signals in the Radio Frequency (RF) band and converts them to intermediate frequencies; c) the up-converter and the power amplifier which convert from the intermediate frequency to RF and amplify the low level RF signals for transmission through the antenna subsystem;
42、 d) the stabilization and tracking subsystems that ensure pointing of the antenna main beam towards the satellite within the required accuracy. NOTE 2: The installation equipment (means of attachment) is outside the scope of the present document. However, the antenna structures and other components
43、directly mounted on the antenna and forming an integral part of it, are subject to the specifications of the present document. below-deck unit: part of the ESV equipment which is not part of the above-deck unit NOTE: This unit is installed inside the vessel and is connected to the above-deck unit. T
44、he connection cable between the above and below-deck units is considered part of the below-deck unit. carrier-off state: ESV is in this state when it is authorized by the Centralized Control and Monitoring Functions (CCMF) to transmit, but when it does not transmit any signal NOTE: The existence of
45、a carrier-off state depends on the system of transmission used. For ESV designed for continuous transmission mode there may be no carrier-off state. carrier-on state: ESV is in this state when it is authorized by the CCMF to transmit and when it transmits a signal transmission disabled state: ESV is
46、 in this state when it is not authorized by the CCMF to transmit transmission enabled state: ESV is in this state when it is authorized by the CCMF to transmit 3.2 Symbols For the purposes of the present document, the following symbols apply: emf electromotive force rms root mean square SINAD (Signa
47、l + Noise + Distortion) / (Noise + Distortion) ETSI ETSI EN 301 843-6 V2.1.1 (2016-03) 8 3.3 Abbreviations For the purposes of the present document, the following abbreviations apply: BA Performance criteria grade A BB Performance criteria grade B CCMF Centralized Control and Monitoring Functions EI
48、RP Equivalent Isotropically Radiated Power EMC ElectroMagnetic Compatibility ESV Earth Station on board a Vessel EUT Equipment Under Test FSS Fixed Satellite Service IF Intermediate Frequency LNB Low Noise Block converter QTMA Quality of Transmission Measurement Apparatus RF Radio Frequency 4 Genera
49、l and operational requirements 4.1 Environmental profile For the purposes of the present document, the test conditions of ETSI EN 301 843-1 1, clause 4, shall apply as appropriate. Further product type related test conditions for Earth Stations on board Vessels are specified in the present document. For emission and immunity tests the normal test modulation, test arrangements, etc., as specified in the present document, clauses 4.1 to 4.5 shall apply. For Earth Stations on board Vessels with or without ancillary equipment, and/or various telecommuni
