1、 ETSI EN 302 617-2 V2.1.1 (2015-12) Ground-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical mobile service using amplitude modulation; Part 2: Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU HARMONISED EUROPEAN STAND
2、ARD ETSI ETSI EN 302 617-2 V2.1.1 (2015-12) 2 Reference REN/ERM-JTFEA-18 Keywords aeronautical, AM, DSB, radio, testing, UHF ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lu
3、cratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the
4、 present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific netwo
5、rk drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the pr
6、esent document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as author
7、ized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2015. All rights reserved. DECTTM, PLUG
8、TESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Associati
9、on. ETSI ETSI EN 302 617-2 V2.1.1 (2015-12) 3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g3Executive summary 6g31 Scope 7g32 References 7g32.1 Normative references . 7g32.2 Informative references 7g33 Definitions and abbreviations . 8g33.1 Definitions 8g33.2 Abbr
10、eviations . 8g34 Technical requirements specifications . 8g34.1 Environmental profile . 8g34.2 Conformance requirements 9g34.2.1 Transmitter requirements 9g34.2.1.0 Applicability 9g34.2.1.1 Frequency error . 9g34.2.1.2 Carrier power (conducted) 9g34.2.1.3 Adjacent channel power 9g34.2.1.4 Conducted
11、spurious emissions 9g34.2.1.5 Intermodulation attenuation 9g34.2.1.6 Keying transient frequency behaviour 9g34.2.1.7 Cabinet Radiation 9g34.2.2 Receiver requirements 10g34.2.2.1 General 10g34.2.2.2 Sensitivity . 10g34.2.2.3 Adjacent channel rejection 10g34.2.2.4 Spurious response rejection . 10g34.2
12、.2.5 Intermodulation response rejection . 10g34.2.2.6 Blocking or desensitization . 10g34.2.2.7 Conducted spurious emissions 10g34.2.2.8 Cross modulation rejection . 10g34.2.2.9 Cabinet radiation . 10g35 Testing for compliance with technical requirements 11g35.1 Environmental conditions for testing
13、. 11g35.2 Interpretation of the measurement results 11g35.3 Radio test suites 12g35.3.1 Transmitter test specifications 12g35.3.1.1 Frequency error . 12g35.3.1.2 Carrier power (conducted) 12g35.3.1.3 Adjacent channel power 12g35.3.1.4 Conducted spurious emissions 12g35.3.1.5 Intermodulation attenuat
14、ion 12g35.3.1.6 Keying transient frequency behaviour 12g35.3.1.7 Cabinet Radiation 12g35.3.2 Receiver test specifications . 12g35.3.2.1 Sensitivity . 12g35.3.2.2 Adjacent channel rejection 13g35.3.2.3 Spurious response rejection . 13g35.3.2.4 Intermodulation response rejection . 13g35.3.2.5 Blocking
15、 or desensitization . 13g35.3.2.6 Conducted spurious emissions 13g35.3.2.7 Cross modulation rejection . 13g35.3.2.8 Cabinet Radiation 13g3ETSI ETSI EN 302 617-2 V2.1.1 (2015-12) 4 Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU .
16、14g3History 16g3ETSI ETSI EN 302 617-2 V2.1.1 (2015-12) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, a
17、nd can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the
18、ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Forew
19、ord This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared in reply to the Commissions standardisation request Commission Implementing Decision C(2015) 5376 final of 0
20、4.08.2015 to provide a means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment. Once the present document is cited in the Official Journal of the European Union u
21、nder that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. The pre
22、sent document is part 2 of a multi-part deliverable covering Ground-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical mobile service using amplitude modulation, as identified below: Part 1: “Technical characteristics and methods of measurement“; Part 2: “Harmonised St
23、andard covering the essential requirements of article 3.2 of the Directive 2014/53/EU“. National transposition dates Date of adoption of this EN: 3 December 2015 Date of latest announcement of this EN (doa): 31 March 2016 Date of latest publication of new National Standard or endorsement of this EN
24、(dop/e): 30 September 2016 Date of withdrawal of any conflicting National Standard (dow): 30 September 2017 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in cl
25、ause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 302 617-2 V2.1.1 (2015-12) 6 Executive summary The present document covers the essential requirements for
26、efficient use of radio spectrum by DSB AM ground base stations, with channel separations of 25 kHz intended for analogue speech. The present document includes necessary changes due to adaption to the new Radio Equipment Directive. ETSI ETSI EN 302 617-2 V2.1.1 (2015-12) 7 1 Scope The present documen
27、t applies to ground based transmitters, receivers and transceivers. These radio equipment types are capable of operating in all or any part of the aeronautical frequency band between 225 MHz and 399,975 MHz. The present document contains requirements to demonstrate that “. Radio equipment shall be s
28、o constructed that it both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference“ i.2. In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the Dire
29、ctive 2014/53/EU i.2 as well as essential requirements under the Single European Sky Interoperability Regulation (as amended) i.3 and related implementing rules and/or essential requirements under the EASA basic regulation 216/2008 i.5 may apply to equipment within the scope of the present document.
30、 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (incl
31、uding any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term
32、 validity. The following referenced documents are necessary for the application of the present document. 1 ETSI EN 302 617-1 (V1.1.1) (01-2009): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Ground-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical m
33、obile service using amplitude modulation; Part 1: Technical characteristics and methods of measurement“. 2 ETSI EN 300 113-1 (V1.6.2) (11-2009): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile service; Radio equipment intended for the transmission of data (and/or speech)
34、 using constant or non-constant envelope modulation and having an antenna connector; Part 1: Technical characteristics and methods of measurement“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. F
35、or specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term valid
36、ity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 ETSI TR 100 028 (all parts) (V1.4.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the mea
37、surement of mobile radio equipment characteristics“. i.2 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. ETSI
38、 ETSI EN 302 617-2 V2.1.1 (2015-12) 8 i.3 Regulation (EC) 552/2004 of the European Parliament and Council of 10 March 2004 on the interoperability of the European Air Traffic Management network (the interoperability Regulation), OJEU L96, 31.03.2004, p. 26-42 as amended by Regulation (EC) 1070/2009
39、of the European Parliament and of the Council of 21 October 2009, OJEU L300/34, 14/11/2009. i.4 ETSI TR 100 028-2 (V1.4.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics; Part 2“. i.5 Regulation (EC) 216/20
40、08 of the European Parliament and of the Council of 20 February 2008 on common rules in the field of civil aviation and establishing a European Aviation Safety Agency, and repealing Council Directive 91/670/EEC, Regulation (EC) No 1592/2002 and Directive 2004/36/EC. 3 Definitions and abbreviations 3
41、.1 Definitions For the purposes of the present document, the terms and definitions given in the Directive 2014/53/EU i.2 and the following apply: aeronautical mobile service: mobile service between aeronautical stations and aircraft stations, or between aircraft stations, in which survival craft sta
42、tions may participate conducted measurements: measurements which are made using a direct RF connection to the equipment under test environmental profile: range of environmental conditions under which equipment within the scope of the present document is required to comply with the provisions of the
43、present document ground base station: aeronautical station equipment, in the aeronautical mobile service, for use with an external antenna and intended for use at a fixed location radiated measurements: measurements which involve the measurement of a radiated field 3.2 Abbreviations For the purposes
44、 of the present document, the following abbreviations apply: AM Amplitude Modulation DSB Double Side Band EASA European Aviation Safety Agency EFTA European Free Trade Association RF Radio Frequency UHF Ultra High Frequency 4 Technical requirements specifications 4.1 Environmental profile The techni
45、cal requirements of the present document apply under the environmental profile for operation of the equipment, which shall be declared by the supplier, but as a minimum, shall be that specified in the test conditions contained in the present document. The equipment shall comply with all the technica
46、l requirements of the present document at all times when operating within the boundary limits of the declared operational environmental profile. ETSI ETSI EN 302 617-2 V2.1.1 (2015-12) 9 4.2 Conformance requirements 4.2.1 Transmitter requirements 4.2.1.0 Applicability All technical requirements in c
47、lause 4.2.1 shall only be applicable to transmitter equipment (including transceiver equipment). 4.2.1.1 Frequency error The frequency error as defined in clause 7.2 of ETSI EN 302 617-1 1 shall not exceed the values shown in table 1 of ETSI EN 302 617-1 1. The conformance test shall be as given in
48、clause 5.3.1.1. 4.2.1.2 Carrier power (conducted) The carrier power as defined in clause 7.3.1 of ETSI EN 302 617-1 1 shall conform to the requirements in clause 7.3.3 of ETSI EN 302 617-1 1. The conformance test shall be as given in clause 5.3.1.2. 4.2.1.3 Adjacent channel power Adjacent channel po
49、wer as defined in clause 7.5.1 of ETSI EN 302 617-1 1 shall conform to the requirements in clause 7.5.3 of ETSI EN 302 617-1 1. The conformance test shall be as given in clause 5.3.1.3. 4.2.1.4 Conducted spurious emissions Conducted spurious emissions as defined in clause 7.7.1 of ETSI EN 302 617-1 1 shall conform to the limits in clause 7.7.3, table 3 of ETSI EN 302 617-1 1. The conformance test shall be as given in clause 5.3.1.4. 4.2.1.5 Intermodulation attenuation Intermodulation attenuation as defined in clause 7.8.1 of ETSI EN 30
