ETSI PRTBR 043-1997 Satellite Earth Stations and Systems (SES) Very Small Aperture Terminal (VSAT) Transmit-Only Transmit-and-Receive Receive-Only Satellite Earth Stations Operatin_1.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

DIN EN ISO 8734-1998 Parallel pins of hardened and martensitic stainless steel (Dowel pins) (ISO 8734 1997) German version EN ISO 8734 1997《淬硬钢和马氏体不锈钢制直销（定位销）》.pdf

DIN EN ISO 8735-1998 Parallel pins with internal thread of hardened and martensitic stainless steel (ISO 8735 1997) German version EN ISO 8735 1997《淬硬钢和马氏体不锈钢制带内螺纹的等直径销》.pdf

DIN EN ISO 8739-1998 Grooved pins - Full-length parallel grooved with pilot (ISO 8739 1997) German version EN ISO 8739 1997《带槽销钉 带导向结构的全长度平行槽销钉》.pdf

DIN EN ISO 8740-1998 Grooved pins - Full-length parallel grooved with chamfer (ISO 8740 1997) German version EN ISO 8740 1997《带槽销钉 带倒角的全长度平行槽销钉》.pdf

DIN EN ISO 8741-1998 Grooved pins - Half-length reverse-taper grooved (ISO 8741 1997) German version EN ISO 8741 1997《带槽销钉 半长度倒锥槽销钉》.pdf

DIN EN ISO 8742-1998 Grooved pins - One-third-length centre grooved (ISO 8742 1997) German version EN ISO 8742 1997《带槽销钉 三分之一长度中心槽销钉》.pdf

DIN EN ISO 8743-1998 Grooved pins - Half-length centre grooved (ISO 8743 1997) German version EN ISO 8743 1997《带槽销钉 半长度中心槽销钉》.pdf

DIN EN ISO 8744-1998 Grooved pins - Full-length taper grooved (ISO 8744 1997) German version EN ISO 8744 1997《带槽销钉 全长度锥型槽销钉》.pdf

DIN EN ISO 8745-1998 Grooved pins - Half-length taper grooved (ISO 8745 1997) German version EN ISO 8745 1997《带槽销钉 半长度锥型槽销钉》.pdf