1、ETSI TS 1 O1 871 -1 VI 2.1 (2003-04) Technical Specificafion Digital Enhanced Cordless Telecommunications (DECT); Application Specific Access Profile (ASAP); DECT Multimedia Access Profile (DMAP); Profile requirement list and profile specific Implementation Conformance Statement (ICs) proforma; Part
2、 1: Portable radio Termination (PT) 2 ETSI TS 101 871-1 V1.2.1 (2003-04) Reference RTS/DECT-040186- 1 Keywords access, data, DECT, ICs, interoperablility, multimedia, network, profile, radio, testing, voice ETSI 650 Route des Lucioles F-O6921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 O0 F
3、ax: +33 4 93 65 47 16 Siret No 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-prfecture de Grasse (06) No 7803/88 Important notice Individual copies of the present document can be downloaded from: http:lwmv.etsi .arq The present document may be made available in more t
4、han one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific netwo
5、rk drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at ha p:/pa rta I. etsi I a rgltbistat uslstatus .as p If you find errors
6、in the present document, send your comment to: Cori vriaht Notifica tion No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. O European Telecommunications Standards Institute 2003. All rights reserved.
7、 DECTTM, PLUGTESTSTMand UMTSTMare Trade Marks of ETSI registered for the benefit of its Members. TIPHONTM and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Or
8、ganizational Partners. ETSI 3 ETSI TS 101 871-1 V1.2.1 (2003-04) Contents Intellectual Property Rights . .5 Foreword . 5 1 Scope 6 2 References . .6 3 Definitions and abbreviations. . .7 Definitions 7 3.1 3.2 Abbreviations . 7 4 Conformance requirement . .7 5 Introduction for completing the ICs prof
9、orma . 8 General . 8 5.1 5.2 Purposes and structure 8 5.3 Abbreviations and conventions 8 Annex A (normative): DMAP Profile ICs Proforma for PT . 10 A. 1 Instruction for completing the ICs proforma . 1 O A.2 Identification of the implementation 1 O A.2.1 Date of the statement 10 A.2.2 Implementation
10、 Under Test (IUT) identification . 10 A.2.3 System Under Test (SUT) identification 11 A.2.4 Product supplier. . 11 Identification of the protocol 12 ICs proforma tables 13 11 . 12 n. A.2.5 Client A.3 A.3.1 A.3.2 Addenda implemented . A.4 Defect report numbers and amendments implemented . A.4.1 A.4.2
11、 A.4.3 A.4.3.1 A.4.3.2 A.4.3.3 A.4.3.4 A.4.3.5 A.4.3.6 A.4.3.7 A.4.4 A.4.4.1 A.4.4.2 A.4.4.3 A.4.4.4 A.4.4.5 A.4.4.6 A.4.4.7 A.4.4.8 A.4.4.9 A.4.5 A.4.5.1 A.4.5.2 A.4.6 A.4.6.1 Global statement of conformance . 13 General Application . 13 Voice services 13 General 13 Network layer . 13 Data link con
12、trol layer 13 Medium access control layer 13 Physical layer. . 13 Management Entity (ME) . 14 Application features. . 14 Data services 14 General 14 General requirements 14 Network layer . 15 15 . . . . . . . ETSI 4 ETSI TS 101 871-1 V1.2.1 (2003-04) A.4.6.2 Profile specific procedures for NWK layer
13、 . 17 Annex B (informative): Bibliography . 18 History 19 ETSI 5 ETSI TS 101 871-1 V1.2.1 (2003-04) Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly ava
14、ilable for ETSI members and non-members, and can be found in ETSI SR 000 3 14: “Intellectual Property Rights (7PRs); Essential, orpotentially Essential, IPRs notlJied to ETSI in respect ofETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web serv
15、er (5). All published ETSI deliverables shall include information which directs the reader to the above source of information. Foreword This Technical Specification (TS) has been produced by ETSI Project Digital Enhanced Cordless Telecommunications (DECT). The present document is part 1 of a multi-p
16、art deliverable covering the DECT Multimedia Access Profile (DMAP); Profile Inplementation Conformance Statement (ICs), as identified below: Part 1: Part 2: “Portable radio Termination (PT)“; “Fixed radio Termination (FT)“. Annex A contains the requirement lists for the PT DECT Multimedia Access Pro
17、file, Application Specific Access Profile. ETSI 6 ETSI TS 101 871-1 V1.2.1 (2003-04) 1 Scope The present document provides the Profile requirement list and profile specific Implementation Conformance Statement proforma for the Digital Enhanced Cordless Telecommunications Multimedia Access Profile (D
18、MAP), Application Specific Access Profile (ASAP) at the Portable radio Termination as defined in EN 301 650 i in compliance with the relevant requirements and in accordance with the relevant guidance given in ISO/IEC 9646-7 5. 2 Re fe re nces The following documents contain provisions which, through
19、 reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication andor edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply For a non-specific reference, the latest vers
20、ion applies. Referenced documents which are not found to be publicly available in the expected location might be found at p. il ETSI EN 30 1 650: “Digital Enhanced Cordless Telecommunications (DECT); DECT Multimedia Access Profile (DMAP); Application Specific Access Profile (ASAP)“. ETSI EN 300 175-
21、1 : “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Part 1 : Overview“. ETSI EN 300 444: “Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP)“. ISO/IEC 9646- 1 : “Information technology; Open Systems Interconnection; Conformance testing meth
22、odology and framework; Part 1 : General concepts“. ISO/IEC 9646-7: “Information technology; Open Systems Interconnection; Conformance testing methodology and framework; Part 7: Implementation Conformance Statements“. ETSI EN 30 1 649: “Digital Enhanced Cordless Telecommunications (DECT); DECT Packet
23、 Radio Service (DPRS)“. ETSI TS 101 869-1 : “Digital Enhanced Cordless Telecommunications (DECT); DECT Packet Radio Services (DPRS); Profile requirement list and profile specific Implementation Conformance Statement (ICs) proforma; Part 1 : Portable radio Termination (PT)“. ETSI EN 300 474- 1 : “Dig
24、ital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP); Profile requirement list and profile specific Implementation Conformance Statement (ICs) proforma; Part 1 : Portable radio Termination (PT)“. 21 31 41 51 61 71 SI ETSI 7 ETSI TS 101 871-1 V1.2.1 (2003-04) 3 3.1 Definitio
25、ns and abbreviations De fi nit ions For the purposes of the present document, the terms and definitions given in EN 300 175-1 2, ISO/IEC 9646-1 4, ISO/IEC 9646-7 5 and the following apply: Implementation Conformance Statement (ICs): statement made by the supplier of an implementation or system claim
26、ed to conform to a given specification, stating which capabilities have been implemented NOTE: The ICs can take several forms: protocol ICs, profile ICs, profile specific ICs, information object ICs, etc. ICs proforma: document, in the form of a questionnaire, which when completed for an implementat
27、ion or system becomes an ICs Protocol ICs (PICS): PICS for an implementation or system claimed to conform to a given protocol specification 3.2 Abbreviations For the purposes of the present document, the abbreviations defined in EN 301 650 i and ISO/IEC 9646-1 4 apply. 4 Conformance requirement The
28、supplier of a protocol implementation, which is claimed to conform to the portable termination specific requirements of EN 301 650 i, shall veriSl that his protocol implementation meets the requirements described in the present document. All the requirements described in TS 101 869-1 7 and EN 300 47
29、4-1 8 apply with the changes indicated in annex A. The clause A.4.2 and its subclauses indicate the general application support. The supplier of the implementation shall complete this part. The clause A.4.3 and its subclauses indicate the profile requirements list and the mandatory clauses for voice
30、 services. The supplier of the implementation, which is claimed to support these services, shall complete this part. The clause A.4.4 and its subclauses indicate the profile requirements list and the mandatory clauses for data services. The supplier of the implementation, which is claimed to support
31、 these services, shall complete this part The clause A.4.5 and its subclauses indicate the profile specific ICs proforma. The supplier of the implementation shall complete this part. An ICs, which conforms to the present document, shall be a conforming ICs proforma completed in accordance with the g
32、uidance for completion given in clause 5. ETSI 8 ETSI TS 101 871-1 V1.2.1 (2003-04) 5 Introduction for completing the ICs proforma 5.1 Gen eral The supplier of a protocol implementation that is claimed to conform to the portable termination specific requirements of EN 301 650 i shall veriSl that his
33、 particular layer protocol implementation meets the profile RL for each layer. For this, he shall complete a copy of the corresponding layer ICs proforma contained in TS 101 869-1 7 for data services and in EN 300 474-1 SI for voice services and updated with the requirements from aimex A. The profil
34、e Requirement List (profile RL) as defined in annex A is based on TS 101 869-1 7 for data services and on EN 300 474-1 SI for voice services. The profile RL is produced by copying selected tables from TS 101 869-1 7 or EN 300 474-1 SI, removing the column(s) to be completed by the supplier, and addi
35、ng a new set of columns giving the new profile requirements, both in terms of the status andor allowed values. The tables defiied in the present document, reference the tables either in TS 101 869-1 7 or in EN 300 474-1 SI, as relevant. 5.2 Purposes and structure The purpose of this ICs proforma is
36、to provide a mechanism whereby a supplier of an implementation of the Portable radio Termination (PT) of the EN 301 650 i may provide information about the implementation in a standardized manner. The ICs proforma is subdivided into clauses for the following categories of information: Identification
37、 of the implementation; Identification of the protocol; ICs proforma tables: Instruction for completing the ICs proforma; - Global statement of conformance; - Other specific clauses. 5.3 Ab b revi at i on s and convent i on s The ICs proforma contained in annex A is comprised of information in tabul
38、ar form in accordance with the guidelines presented in ISO/IEC 9646-7 5. Item column The item column contains a number, which identifies the item in the table. Item description column The item description column describes in free text each respective item (e.g. parameters, timers, etc.). It implicit
39、ly means “is supported by the implementation?“. Profile reference column The reference column gives reference to EN 301 650 i, except where explicitly stated otherwise. ETSI 9 ETSI TS 101 871-1 V1.2.1 (2003-04) Status column The following notations, defined in ISO/IEC 9646-7 5, are used for the stat
40、us column: M or m O or o X or x 0.i or 0.i Ci or ci I or i mandatory - the capability is required to be supported. optional - the capability may be supported or not (e.g. the capability is not allowed because the underlying DECT layers (service provider) cannot handle it or the requirement belongs t
41、o an application i.e. does not belong to the network layer). prohibited (excluded) - there is a requirement not to use this capability in the given context. qualified optional - for mutually exclusive or selectable options from a set. “i“ is an integer which identifies a unique group of related opti
42、onal items and the logic of their selection which is defied immediately following the table. conditional - the requirement on the capability (“m“, “o“, “x“ or “n/a“ depends on the support of other optional or conditional items. “i“ is an integer identiSling a unique conditional status expression whi
43、ch is defined immediately following the table or which is defined in a general condition table. out-of-scope - this capability is outside the scope of the given specification, and hence irrelevant and not subject to conformance testing. This status is in particular applicable for data fields, which
44、are reserved for future use. The structure of such fields has to be supported, but the value is undefined and thus to be ignored. Support column The support column shall be filled in by the supplier of the implementation. The following common notations, defined in ISO/IEC 9646-7 5, are used for the
45、support column: Y or y N or n N/A, n/a or - supported by the implementation not supported by the implementation no answer required (allowed only if the status is n/a, directly or after evaluation of a conditional status) Prerequisite line A prerequisite line takes the form: Prerequisite: . A prerequ
46、isite line before a clause or table title indicates that the whole clause or the whole table is not required to be completed if the predicate is FALSE. ETSI 10 ETSI TS 101 871-1 V1.2.1 (2003-04) Day Annex A (normative): DMAP Profile ICs Proforma for PT Month Year Notwithstanding the provisions of th
47、e copyright clause related to the text of the present document, ETSI grants that users of the present document may freely reproduce the ICs proforma in this annex so that it can be used for its intended purposes and may further publish the completed ICs. A.l Instruction for completing the ICs profor
48、ma The supplier of the implementation shall complete the ICs proforma in each of the spaces provided. In particular, an explicit answer shall be entered, in each of the support or supported column boxes provided, using the notation described in clause 5. A.2 Identification of the implementation A.2.
49、1 Date of the statement Identification of the Implementation Under Test (IUT) and the system in which it resides (the System Under Test (SUT) should be filled in so as to provide as much detail as possible regarding version numbers and configuration options. The product supplier information and client information should both be filled in if they are different. A person who can answer queries regarding information supplied in the ICs should be named as the contact person. A.2.2 Implementation Under Test (i UT) identificati
