1、 ETSI TS 103 158 V1.1.1 (2014-11) Digital Enhanced Cordless Telecommunications (DECT); New Generation DECT; Light Data Services; Software Update Over The Air (SUOTA); Profile Test Specification (PTS) and Test Case Library (TCL) TECHNICAL SPECIFICATION ETSI ETSI TS 103 158 V1.1.1 (2014-11)2Reference
2、DTS/DECT-NG270 Keywords DECT, interoperability, interworking, packet mode, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Gra
3、sse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior w
4、ritten authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present docu
5、ment should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the foll
6、owing services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version
7、shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2014. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered
8、 for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 103 158 V1.1.1 (2014-11)3Content Intellectual Prop
9、erty Rights 5g3Foreword . 5g3Modal verbs terminology 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 6g33 Definitions, symbols and abbreviations . 7g33.1 Definitions 7g33.2 Symbols 7g33.3 Abbreviations . 8g34 Test method 8g34.1 Test platform 9g34.1.1 PP test pl
10、atform . 9g34.1.1.1 PP test platform main requirements 9g34.1.1.2 Test content for HTTP-based applications, Simple profile . 9g34.1.1.2.1 Test url and index page: index.html 9g34.1.1.2.2 Left page: pages/left.html 9g34.1.1.2.3 Center page: pages/center.html 9g34.1.1.2.4 Right page: pages/right.html
11、9g34.1.1.3 Test content for HTTP-based applications, Baseline profile . 10g34.1.1.3.1 Test url and index page: index.html 10g34.1.1.3.2 Left page: pages/left.html 10g34.1.1.3.3 Center page: pages/center.html 10g34.1.1.3.4 Right page: pages/right.html 10g34.1.2 FP test platform . 10g34.1.2.1 FP test
12、platform main requirements 10g34.1.2.2 Test content for software upgrade (TS_1 + MS) . 11g34.2 Hypothesis 12g34.3 Test groups . 12g34.3.1 Network features . 12g34.3.2 Application features 12g35 Test Cases (TCs) 12g35.1 TC definition conventions 13g35.1.1 Test equipment implementation requirements 13
13、g35.1.2 Definitions of used MACROs (PT and FT sides) . 14g35.1.2.1 Basic service MACROs (request from PP to FP) 14g35.1.2.1.1 Suota C-plane 14g35.1.2.1.2 Binary content download . 14g35.1.2.1 Handset version indication MACRO (request from PP to FP) 15g35.1.2.2 Handset version available MACRO (from F
14、P to PP) 15g35.1.2.3 HTTP related MACROS . 15g35.1.2.3.1 Submacros . 15g35.1.2.3.2 range request MACRO (from PP to FP) 16g35.1.2.3.3 HTTP range response MACRO (from FP to PP) 16g35.1.2.3.4 HTTP error MACRO (from FP to PP) 16g35.2 TC naming conventions 16g35.3 Portable Part TC purposes 17g35.3.1 List
15、 of New Generation DECT Part 4 PT tests cases 17g35.4 Fixed Part TC purposes 19g35.4.1 List of New Generation DECT Part 4 FT tests cases 19g36 Portable Part Test specification 22g3ETSI ETSI TS 103 158 V1.1.1 (2014-11)46.1 DPRS PT Procedures 22g36.2 NGLDS-N.1 General Light Data Service Procedures 28g
16、36.3 NGLDS-N.2 Software upgrade over the air, C-plane . 31g36.4 NGLDS-A.1 Binary content download 38g36.5 NGLDS-A.2 Software upgrade over the air . 39g36.6 NGLDS-A.3 HTTP based applications 46g37 Fixed Part Test specification 47g37.1 DPRS FT Procedures 48g37.2 NGLDS-N.1 General Light Data Service Pr
17、ocedures 55g37.3 NGLDS-N.2 Software upgrade over the air, C-plane . 57g37.4 NGLDS-A.1 Binary content download 60g37.5 NGLDS-A.2 Software upgrade over the air . 61g37.6 NGLDS-A.3 HTTP based applications 71g3Annex A (normative): Declarations on features and procedures supported 73g3A.1 Declarations fo
18、r portable part . 73g3A.1.1 Optional PT features . 73g3A.1.2 Extra information for PT testing . 73g3A.1.3 Optional or conditional PT procedures . 74g3A.2 Declarations for fixed part 75g3A.2.1 Optional FT features . 75g3A.2.2 Extra information for FT testing . 75g3A.2.3 Optional or conditional FT pro
19、cedures . 75g3Annex B (informative): List of NG-DECT Part 4 procedures . 76g3Annex C (normative): Configuration for testing . 78g3C.1 Portable part configuration to be declared by supplier . 78g3C.2 Fixed part internal configuration to be declared by supplier 78g3C.3 Test environment configuration t
20、o be declared by test house or supplier 78g3Annex D (normative): Amendments to other DECT specifications 79g3Annex E (informative): Bibliography . 80g3History 81g3ETSI ETSI TS 103 158 V1.1.1 (2014-11)5Intellectual Property Rights IPRs essential or potentially essential to the present document may ha
21、ve been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI stand
22、ards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not refe
23、renced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Digital Enhanced Cordless Telecommunications (DECT). The present document
24、 is the Test Specification for testing compliance with ETSI TS 102 527-4 5. “Digital Enhanced Cordless Telecommunications (DECT); New Generation DECT; Part 4: Light Data Services; Software Update Over The Air (SUOTA), content downloading and HTTP based applications“. The information in the present d
25、ocument is believed to be correct at the time of publication. However, DECT standardization is a rapidly changing area and it is possible that some of the information contained in the present document may become outdated or incomplete within relatively short time-scales. Modal verbs terminology In t
26、he present document “shall“, “shall not“, “should“, “should not“, “may“, “may not“, “need“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT al
27、lowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 103 158 V1.1.1 (2014-11)61 Scope The present document contains the Profile Test Specification (PTS) and the Test Case Library (TCL) for “New Generation DECT; Part 4“Digital Enhanced Cordless Telecommunications (DECT); New G
28、eneration DECT; Part 4: Light Data Services; Software Update Over The Air (SUOTA), content downloading and HTTP based applications“ The present document covers both the Portable (PT) and the Fixed (FT) Radio terminations. The Test Case Library (TCL) covers also some test cases for “DECT Digital Pack
29、et Radio Service“ i.4. This is done because such test cases are mandatory or especially relevant for New Generation DECT Part 4 (see ETSI TS 102 527-4 5). The objective of the present document is to provide a basis for approval tests of NG-DECT Part 4 5 equipment giving a high probability of air int
30、erface inter-operability between different manufacturers DECT equipment. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references,only the cited version applies. For non-specific references, the l
31、atest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publ
32、ication, ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are necessary for the application of the present document. 1 ETSI EN 300 175-5: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Part 5: Network (NWK) laye
33、r“. 2 ETSI EN 300 444: “Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP)“. 3 ETSI TS 102 527-1: “Digital Enhanced Cordless Telecommunications (DECT); New Generation DECT; Part 1: Wideband speech“. 4 ETSI TS 102 527-3: “Digital Enhanced Cordless Telecommunications (DE
34、CT); New Generation DECT; Part 3: Extended wideband speech services“. 5 ETSI TS 102 527-4: “Digital Enhanced Cordless Telecommunications (DECT); New Generation DECT; Part 4: Light Data Services; Software Update Over The Air (SUOTA), content downloading and HTTP based applications“. 6 ETSI TS 102 527
35、-5: “Digital Enhanced Cordless Telecommunications (DECT); New Generation DECT; Part 5: Additional feature set nr. 1 for extended wideband speech services“. 2.2 Informative references The following referenced documents are not necessary for the application of the present document but they assist the
36、user with regard to a particular subject area. i.1 World Wide Web Consortium Recommendation XHTML 1.1: “Module-based XHTML - Second Edition“ - 23 November 2010. NOTE: http:/www.w3.org/TR/2010/REC-xhtml11-20101123/. ETSI ETSI TS 103 158 V1.1.1 (2014-11)7i.2 ISO/IEC 9646-7:1995: “Information technolog
37、y - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements“. i.3 ETSI TS 102 841: “Digital Enhanced Cordless Telecommunications (DECT); New Generation DECT; Extended wideband speech services; Profile Test Specification (PTS) and T
38、est Case Library (TCL)“. i.4 ETSI EN 301 649: “Digital Enhanced Cordless Telecommunications (DECT); DECT Packet Radio Service (DPRS)“. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ETSI TS 102 527-5 6, ETSI TS 10
39、2 527-3 4, ETSI TS 102 527-1 3, ETSI EN 300 444 2 and the following apply: GAP (PP, FP, device or equipment): PP, FP or any of them compliant with ETSI EN 300 444 2. golden device: ideal example of a device used as reference device for compliance testing and against which later devices are tested an
40、d judged NG-DECT Part 1 Golden Device: Golden Device, such as the one administered by the DECT Forum, used for compliance testing of NG-DECT Part 1 3 equipment NG-DECT Part 1 (PP, FP, device or equipment), also shortened as Part 1 (PP, FP, device or equipment): PP, FP or any of them compliant with E
41、TSI TS 102 527-1 3 NG-DECT Part 3 (PP, FP, device or equipment), also shortened as Part 3 (PP, FP, device or equipment): PP, FP or any of them compliant with ETSI TS 102 527-3 4 NG-DECT Part 4 (PP, FP, device or equipment), also shortened as Part 4 (PP, FP, device or equipment): PP, FP or any of the
42、m compliant with ETSI TS 102 527-4 5 NG-DECT Part 5 (PP, FP, device or equipment), also shortened as Part 5 (PP, FP, device or equipment): PP, FP or any of them compliant with ETSI TS 102 527-5 6 provision mandatory, process mandatory: indicated feature service or procedure are implemented as descri
43、bed in the present document, and may be subject to testing provision optional, process mandatory: indicated feature, service or procedure may be implemented, and if implemented, the feature, service or procedure are implemented as described in the present document, and may be subject to testing NOTE
44、: The notation used is based on the notation proposed in ISO/IEC 9646-7 i.2. 3.2 Symbols For the purposes of the present document, the following symbols apply: C conditional to support (process mandatory) E Test Parameter used in parameterized tests for an HTTP Error I out-of-scope (provision option
45、al, process optional) not subject for testing M mandatory to support (provision mandatory, process mandatory) MSO Test Parameter used in parameterized tests for indicating the MS origin (manufacturer or 3rdparty) N/A not applicable (in the given context the present document makes it impossible to us
46、e this capability) O optional to support (provision optional, process mandatory) SUF Test Parameter used in parameterized tests for the (variable) suffix of the software version URLP Test Parameter used in parameterized tests for an URL Parameter ETSI ETSI TS 103 158 V1.1.1 (2014-11)83.3 Abbreviatio
47、ns For the purposes of the present document, the following abbreviations apply: BCD Binary Content Download CC Call Control CI Common Interface DECT Digital Enhanced Cordless Telecommunications DLC Data Link Control DS Download ServerFP Fixed PartFT Fixed radio Termination GAP Generic Access Profile
48、 HTTP HyperText Transfer Protocol IE Information Element IUT Implementation Under Test IWU InterWorking Unit IXIT Implementation eXtra Information for Testing LDS Light Data Services MAC Medium Access Control MS Management ServerNG New GenerationNG-DECT New Generation DECT NWK NetWorK PHL PHysical L
49、ayer PP Portable PartPT Portable radio Termination PTS Profile Test Specification RF Radio Frequency TCL Test Case Library TS Test System 4 Test method This clause describes the test method used to test the NG DECT Part 4 devices. g3DECT DLC DECT MAC DECT PHL Tester Test System Device Under Test DECT DLC DECT MAC DECT PHL DECT NWK IUT Application NWK PDUs Figure 1: New Generation DECT remote test method A tester (see figure 1) is located in a remote DECT test system. It controls and observes the behaviour of the Implemen
